Drive a Type / Drive B Type, Video, Cga | Multi-Tech Systems RAS96

4 BIOS Setup Utility

You can use the IDE HDD Auto Detection option in the main menu to automatically enter the specifications for your hard disk. If you wish to configure your drive manually, press PAGE UP or PAGE DOWN to select User. Enter your drive’s specifications in the drive table. The hard disk will not work properly if you enter improper information.

If you select User, you will need to know the following information. Enter the information directly from the keyboard and press ENTER. This information should be included in the documentation from your hard disk vendor or the system manufacturer.

CYLS	Number of cylinders.
HEAD	Number of heads.
PRECOMP	Write precompensation.
LANDZ	Landing zone.
SECTORS	Number of sectors.
MODE	IDE mode: Normal, for drives under 528 MN; LBA, for larger drives
	that support Logical Block Addressing (most IDE drives over 528
	MB); Large, for drives over 528 MB that do not support LBA
	(uncommon); and Auto, for autoselection on boot-up (default).

If a hard disk has not been installed, select None and press ENTER.

Drive A Type / Drive B Type

This category identifies the types of floppy disk drives that have been installed in the computer.

None

360K, 5.25 in 1.2M, 5.25 in 720K, 3.5 in 1.44M, 3.5 in 2.88M, 3.5 in

No floppy drive installed.

5.25-inch PC-type standard drive, 360-kilobyte capacity.

5.25-inch AT-type high-density drive, 1.2-megabyte capacity. 3.5-inch drive, 720-kilobyte capacity.

3.5-inch drive, 1.44-megabyte capacity (default – drive A).

3.5-inch drive, 2.88-megabyte capacity.

Video

The category selects the type of video adapter used for the primary system monitor. Although secondary monitors are supported, you do not have to select the type in Setup.

EGA/VGA	Enhanced Graphics Adapter/ Video Graphics Array. For EGA,
	VGA, SEGA, SVGA or PGA monitor adapters (default).
CGA 40	Color Graphics Adapter, power-up in 40 column mode.
CGA 80	Color Graphics Adapter, power-up in 80 column mode.
MONO	Monochrome adapter, includes high resolution monochrome
	adapters.

CommPlete Communications Server

25

Image 31

Multi-Tech Systems RAS96 manual Drive a Type / Drive B Type, Video, Cga

Contents

RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Iii Important Safety Instructions Table of Contents Appendix C Post Codes Solving ProblemsPage Introduction Manual Organization Introduction Appendix D Approved Memory Technical SpecificationsAppendix B Post Messages Appendix C Post Codes Humidity range 20-90% noncondensing RASCard Description RAS96 RASCard Memory Banks Jumpers J17 Watchdog TimerJ14, J15, J16, J18 CPU Frequency Selection Internal Connectors J35 Video External ConnectorsJ2 Power Connector J22 E1 Alarm E1 Status LEDs LED IndicatorsFront Panel Ethernet Status LEDs Power Switch SwitchesReset Switch Page Installation Pre-Installation Notes Safety WarningsInstallation Procedure Installation Page Bios Setup Utility Starting Setup Case of Problems Using SetupGetting Help Power Management Setup Standard Cmos SetupBios Features Setup Chipset Features Setup Password Setting PCI Configuration SetupLoad Bios Defaults IDE HDD Auto Detection Load Setup Defaults Exit Without Saving Save and Exit Setup Hard Disks Standard Cmos SetupDate Time Video Drive a Type / Drive B TypeCGA Memory Halt On Virus Warning Bios Features SetupEnabled Disabled Boot Up NumLock Status Quick Power On Self TestBoot Sequence Boot Up Floppy Seek Typematic Rate Chars/Sec Typematic Rate SettingGate A20 Option Memory Parity Check C8000 Cffff Shadow/DC000 Dffff Shadow Typematic Delay MsecVideo Bios Shadow Security Option System Bios Cacheable Chipset Features SetupDram Timing Memory Hole At 15M-16M Video Bios CacheableBit I/O Recovery Time IDE HDD Block Mode PCI Bursting On-Chip Primary PCI IDEPCI Concurrancy PCI Streaming Power Management Power Management Setup HDD Power Down Doze ModeStandby Mode Suspend Mode Drive Ports Accessed Power Down ActivitiesCOM Ports Accessed LPT Ports Accessed Slot x Using INT# PCI Configuration Setup1st/2nd/3rd/4th Available IRQ PCI IDE IRQ Map to PCI IRQ Activated by Enter Password Password SettingPage E1 Daughter Cards E1 Overview Specifications E1 Glossary E1 Basics Dnis digits Signaling OptionsE1 Frame Formats E1 Line Coding Country Selection E1 Facility Termination Pin Signal Test Modes RJ-11 Alarm JackPCB Description E1 Line Monitoring Jack Line Coding Configuration of the E1 Daughter CardOrdering an E1 Line Channelized E1 line with 30 DS-0 channels E1 Frame Format Factory Defaults To Configure the E1 Daughter Card Command Example E1 Commands RAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Status LEDs E1 Command Messages Functional Description Solving Problems RASCard has no video Troubleshooting COM1 port does not respond correctly Invalid time, date or setupKeyboard does not respond to key strokes Memory Upgrade Calling Technical Support Diagnostic Tests RAS96 RASCard User Guide Appendixes Keyboard Connector J11 Appendix a Connector PinoutsVideo Connector J35 E1 Alarm Connector J22 COM1 Connector J3 Drive Power Connector J13 Pin Floppy Disk Drive Connector J27 IOCS16 Hard Disk Connector J6 Figure A-7. IDE connector IDE Connector J21 Appendix B Post Messages Error MessagesPost Beep Memory parity Error at Memory Address Error atMemory Verify Error at Offending Segment Code Name Description Appendix C Post Codes Post Codes E1-EF Capacity Speed Type Manufacturer Part Number Usable MB Appendix D Approved Memory Appendix E Regulatory Information EMC, Safety and Terminal Directive Compliance