PCI Configuration Setup | Multi-Tech Systems RAS96 specification

4 BIOS Setup Utility

PCI Configuration Setup

This setup page allows you to set up your computer for efficient energy levels. See page 37.

Password Setting

Change, set, or disable the password. The password allows you to limit access to the system and the Setup Utility, or just to the Setup Utility. See page 39.

Load BIOS Defaults

The BIOS defaults have been set by the manufacturer. They provide settings that provide the minimum requirements for your system to operate.

CommPlete Communications Server

21

Image 27

Multi-Tech Systems RAS96 manual PCI Configuration Setup, Password Setting, Load Bios Defaults

Contents

RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Iii Important Safety Instructions Table of Contents Appendix C Post Codes Solving ProblemsPage Introduction Manual Organization Introduction Appendix D Approved Memory Technical SpecificationsAppendix B Post Messages Appendix C Post Codes Humidity range 20-90% noncondensing RASCard Description RAS96 RASCard Memory Banks J17 Watchdog Timer JumpersJ14, J15, J16, J18 CPU Frequency Selection Internal Connectors J35 Video External ConnectorsJ2 Power Connector J22 E1 Alarm E1 Status LEDs LED IndicatorsFront Panel Ethernet Status LEDs Switches Power SwitchReset Switch Page Installation Safety Warnings Pre-Installation NotesInstallation Procedure Installation Page Bios Setup Utility Starting Setup Using Setup Case of ProblemsGetting Help Power Management Setup Standard Cmos SetupBios Features Setup Chipset Features Setup PCI Configuration Setup Password SettingLoad Bios Defaults IDE HDD Auto Detection Load Setup Defaults Exit Without Saving Save and Exit Setup Hard Disks Standard Cmos SetupDate Time Drive a Type / Drive B Type VideoCGA Memory Halt On Virus Warning Bios Features SetupEnabled Disabled Boot Up NumLock Status Quick Power On Self TestBoot Sequence Boot Up Floppy Seek Typematic Rate Chars/Sec Typematic Rate SettingGate A20 Option Memory Parity Check C8000 Cffff Shadow/DC000 Dffff Shadow Typematic Delay MsecVideo Bios Shadow Security Option Chipset Features Setup System Bios CacheableDram Timing Memory Hole At 15M-16M Video Bios CacheableBit I/O Recovery Time IDE HDD Block Mode PCI Bursting On-Chip Primary PCI IDEPCI Concurrancy PCI Streaming Power Management Power Management Setup HDD Power Down Doze ModeStandby Mode Suspend Mode Drive Ports Accessed Power Down ActivitiesCOM Ports Accessed LPT Ports Accessed PCI Configuration Setup Slot x Using INT#1st/2nd/3rd/4th Available IRQ PCI IDE IRQ Map to PCI IRQ Activated by Enter Password Password SettingPage E1 Daughter Cards E1 Overview Specifications E1 Glossary E1 Basics Dnis digits Signaling OptionsE1 Frame Formats E1 Line Coding Country Selection E1 Facility Termination Pin Signal Test Modes RJ-11 Alarm JackPCB Description E1 Line Monitoring Jack Line Coding Configuration of the E1 Daughter CardOrdering an E1 Line Channelized E1 line with 30 DS-0 channels E1 Frame Format Factory Defaults To Configure the E1 Daughter Card Command Example E1 Commands RAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Status LEDs E1 Command Messages Functional Description Solving Problems RASCard has no video Troubleshooting Invalid time, date or setup COM1 port does not respond correctlyKeyboard does not respond to key strokes Memory Upgrade Calling Technical Support Diagnostic Tests RAS96 RASCard User Guide Appendixes Appendix a Connector Pinouts Keyboard Connector J11Video Connector J35 E1 Alarm Connector J22 COM1 Connector J3 Drive Power Connector J13 Pin Floppy Disk Drive Connector J27 IOCS16 Hard Disk Connector J6 Figure A-7. IDE connector IDE Connector J21 Error Messages Appendix B Post MessagesPost Beep Memory Address Error at Memory parity Error atMemory Verify Error at Offending Segment Code Name Description Appendix C Post Codes Post Codes E1-EF Capacity Speed Type Manufacturer Part Number Usable MB Appendix D Approved Memory Appendix E Regulatory Information EMC, Safety and Terminal Directive Compliance