Ethernet Setting | NetComm NCT480 manual

Ethernet Setting

The Ethernet Interface allows you to manage the network Ethernet port.

NCT480 IP DSLAM has two GE interface for uplink/downlink purposes. The IP address associates with the uplink and downlink interface are only for system management purpose. The IP address assigned to the Ethernet ports must be in different subnets.

Figure 4-12 Ethernet Port Configuration Dialog

Select an Ethernet Port to show the parameters, edit the control value in text box and click ‘Apply’ to modify or click ‘Add’ to create a new Ethernet port.

Item

Description

Ethernet Port pull down menu	Select the Ethernet port from pull down menu.

IP Address	This specifies the network IP address of given Ethernet interface. This IP address is for
	system management use only.
	Valid values: Any valid class A/B/C address

Net Mask	This specifies the network mask configured for the interface.
	Valid values: 255.0.0.0 ~ 255.255.255.255

Is use DHCP	This indicates whether a DHCP client is to be triggered to obtain an IP address for this
	Ethernet interface.

Interface Type	The type of Ethernet interface, net or slave.

Actual Duplex Mode	The duplex mode use by the Ethernet interface.

Output Rate Limit	This parameter specifies the output rate limiting value to be applied on this interface. The
	unit is in Mbits/sec. This setting will have effect on receiving data rate of specified port.
	Valid values: 0 ~ 300 Mbps

Management VLAN ID	VLAN for management traffic on this interface. Nonzero value of this field is valid only if
	either ‘IP Address’ field is non-zero or ‘does use DHCP’ field is true. If no Management
	VLAN ID is specified (in the create operation) or its value is set to zero (either in create
	or modify operation) then the system shall use the value of ‘private VLAN ID’ associated
	with the bridge port created on this interface as the Management VLAN ID.
	In case the management VLAN (i.e. ‘Management VLAN ID’ or the associated ‘private
	VLAN ID’, if ‘Management VLAN ID’ is zero) does not exist on the system then IP based
	management on this management VLAN shall not happen on the interface till the
	corresponding VLAN is created with the Network side port as its member.
	Default values: 0
	Valid values: 0 ~ 4094

NCT480 IP DSLAM User Guide	YML856 Rev3
70	www.netcomm.com.au

Image 70

NetComm NCT480 manual Ethernet Setting

Contents

User Guide NCT480 IP Dslam User Guide Contents System Installation Guide Front View Rear View Side View Alarm I/O Module Organization PrefacePurpose Conventions Product Overview Introduction to the NCT480 Features Field Applications NCT480 IP-DSLAM Service Applications NCT480 Link Aggregation Illustrate Service Provider Demarcation NCT480 System Overview Power LEDFault Front View 1 ~ 24 voice port connect to Pstn GE1/GE2Pots J1 Pots J2 Rear View Alarm I/O ModuleSide View Local Management System ManagementIP Network Management Preparing for Installation Safety Requirements Safety Guidelines Use caution when installing or modifying telephone lines General Maintenance Guidelines Preventing Electrostatic Discharge Damage Site Requirements Environmental Requirements Fan unit Air flow PowerCFM Cabling Rack Mounting Tools and Equipment Required Check Tools and Equipment Unpacking the NCT480 System Verifying ContentsInspecting for Damage Installing the NCT480 Installation Checklist Install the NCT480 Box Chassis NCT480 System Installation ProceduresMeasure Rack Space Connecting a Console Parameter Setting Connecting the RJ-21 Subscriber Line Interface Rear Panel RJ-21 Connector Cabling for NCT480 Connecting the RJ-45 Network Uplink Interface Front Panel RJ-45 Network Uplink Cabling for NCT480 Attach and Apply Power Front Panel AC Power Connection for NCT480 Earth Ground of NCT480 Hardware Specification System SpecificationsRJ-45 to RS-232 Female DB-9 adaptor cable NCT480 System Specification Software Specification Vlan 802.1Q MIB IF-MIBRFC 2515 ATM MIB RFC 3440 Adsl line MIB Reboot System Web Management Operation Guide Add Trunk Vlan Preface Login Window Getting Started Web Management Operation Window Overview NCT480 FW R2.32 Web Management Interface Operation Window System Menu General Information DnLink Ucast Addr Count Statistics InformationCPE Ucast Addr Count Net Ucast Addr Count User and Password User Name This specifies the user name to be created Bridge Mode Status of full Bridging Status Ports without doing a lookup in the forwarding table Backup Configuration Backup and RestoreRestore Configuration Browse… Upgrade Clear Firmware UpgradeClick this to clear the location of the file in this field Commit Configuration Commit and RebootReboot System Vpci VPI/VCI Restore Factory ConfigurationLlcmux Status and Performance DSL Status ATU-R Transmitted Blocks Agent was resetLayer Information Corrected Blocks Ethernet Statistics PVC Statistics Line 15min Performance Alarm I/O Status Line 1day Performance Deployment Menu Select port to be enabled or disabledAdmin status Display port status DSL Port DSL Profile Configuration DSL Profile Configuration Add DSL Profile Maximum SNR Margin Transmit power to get a noise margin below this limitPower Management Power Management mode Minimum SNR Margin 310 DSL Profile MappingMinimum Tx Rate Kbps Maximum Tx Rate Kbps Atuc Atur Default DSL Profile Setting DSL Alarm Profile LOSsec LOP sec ES sec Sesl sec Uasl sec Power Management Mode Power Management Forced State PVC Setting VPI VCI Add Port & PVC Vlan ID Set PPPoA MAC Set PPPoA MAC Dialog Route Setting 10 Display the Routing Table Ethernet Setting DHCP’ field is true Tagged PDU ManagementPriority Port Speed Use Dhcp Add Ethernet InterfaceNetwork Type Network Snmp Host AccessCommunity Community name This specifies the community name Community AccessSnmp Community Space Alarm I/O Control ‑18 Alarm I/O Control Dialog Ethernet valid values 1 ~ Access ControlMAC Limit DSL valid values 1 ~ Port ACL Configuration Dialog Port ACL Global ACL Deny MAC Address Source MAC address to be dropped Protocol Menu Vlan Port Trunk Vlan Setting Trunk Vlan Setting Dialog Add Trunk Vlan Values 0~4095 is reserved for priority tag, 4095 is reserved Vlan Mode Setting Network Scenario Vlan mode Can be used to meet custom Vlan stacking requirements Igmp Snooping VPI/VCI Dhcp & PPPoE Relay Spanning Tree Protocol Setting Dialog Spanning Tree Protocol Rapid Spanning Tree Protocol Hello Time Forward DelayBridge Forward Delay Hold Time Diagnostic Menu DSL Bin Information Virtual circuit for which information is desired ATM OAM TestPortvpi/vci Result ADSL2 Delt Test RtVBR Appendix a Abbreviations and AcronymsSCR SNR Snmp UAS UBR VCI VCL Vdsl Vlan VPI VTU-O VTU-R WAN ADSL/VDSL RJ-21 xDSL Connector Port Mapping Appendix B System Connector Pin-OutsTip None Tip Line /POTS Standard Telco Color ChartLine / Pots RJ-45 Management Ethernet Connector Pin-Outs TP0 + TP1 + TP2 + TP3 + GND Gndf Local Console Connector Pin-OutsTxD RxD DTE Ready DCE Ready Appendix C Legal & Regulatory Information Customer Information Product Warranty Limitations of Warranty 101 NCT480 IP Dslam User Guide 103 NCT480 IP Dslam User Guide 105 NCT480 IP Dslam User Guide 107 NCT480 IP Dslam User Guide 109 NCT480 IP Dslam User Guide 111 NCT480 IP Dslam User Guide 113 NCT480 IP Dslam User Guide 115 NCT480 IP Dslam User Guide 117 NCT480 IP Dslam User Guide 119 NCT480 IP Dslam User Guide 121 NCT480 IP Dslam User Guide 123 NCT480 IP Dslam User Guide 125 NCT480 IP Dslam User Guide 127 NCT480 IP Dslam User Guide 129 NCT480 IP Dslam User Guide 131 NCT480 IP Dslam User Guide 133 NCT480 IP Dslam User Guide 135 NCT480 IP Dslam User Guide 137 NCT480 IP Dslam User Guide 139 NCT480 IP Dslam User Guide 141 NCT480 IP Dslam User Guide 143 NCT480 IP Dslam User Guide 145 NCT480 IP Dslam User Guide 147 NCT480 IP Dslam User Guide 149 NCT480 IP Dslam User Guide 151 NCT480 IP Dslam User Guide 153 NCT480 IP Dslam User Guide 155 NCT480 IP Dslam User Guide 157 NCT480 IP Dslam User Guide 159 NCT480 IP Dslam User Guide 161 NCT480 IP Dslam User Guide 163 Contact Information