Nortel Networks 5399 Remote Access Concentrator Parameters

Nortel Networks 5399 Access Switch Hardware Installation Guide

Chapter2 Installingthe Model5399 Remote Access ConcentratorModule

2-18

Remote Access Concentrator Parameters

TheRemote Access Concentrator requires that youset certain parameters

from the ROMm onitorbefore booting the unit from a host. Once the

RemoteAccess Concentrator is booted, you can change these parameters

usingthe na utility. Any changes to these parameters will require the unit

to be rebooted to takeeffect. Ta ble 2- 4 providesa brief description of

theseparameters.

Table2-4. Server Parameters

Parame ter Description

Internetaddress Aunique 32-bit universal identifier that is

specifiedin dotted-decimal notation.

Subnetmask Defineswhich portion of the Internet address

isthe network (all ones), the subnet (all ones),

andthe host (all zeros) address.

Preferredload host address The Internet address of the host from which

youwant to boot.

Load/dumpgateway

Internetaddress TheInternet address of the router, for which

youwill be prompted, if the preferred load

hostis on a different network.

Broadcastaddress AnInternet address with a host id of all ones

(orall zeros for s upportof older 4.2 BSD

systems) to which all hosts on a part icular

subnetwill respond.

Typeof IP encapsulation Specifiesthe method for accessing the

physicaland network layer of the transmission

media.The default is: ethernet (forDIX

Ethernet-II).This parameter can also be set to

ieee802(alsoreferredtoasLLC/SNAP).

Broadcastflag Determineswhether the Remote Access

Concentratorwill broadcast for a load host if it

doesn’thave one.

Contents

Main ii Copyright 1999 Nortel Networks Trademarks Statement of Conditions USA Requirements Only European RequirementsOnly Page iv Canada Requirements Only FCC Part 68 Compliance Statement vi Nortel Networks NA Inc. Softw are License Agreement Page viii Contents Chapter1 Introduction Chapter2 Installingthe Model 5399 Remote Access Concentrator Module Chapter3 ROM MonitorCommands Page Figures Page Tabl es Page Preface Before YouBegin Text Conventions Hard-Copy TechnicalManuals How to Get Help Page Page Model 5399 Description Module Features System 5000 Common Management Bus System 5000 Backplane Ethernet Segment Banks System 5000 Service Port Management Firmware and Software Page Front Panel Nortel Networks 5399 Access Switch Hardware Installation Guide Chapter1 Introduction 1-8 Figure1-3. Model 5399 Remote Access Concentrator Front Panel Front Panel Components Annunciator The Annunciator backlights the model number of the module and Page Page Page Physical Characteristics Page Page Chapter 2 Installing the Model 5399 Remote Access Concentrator Module T Before you Begin Page Installing the Model 5399 Remote Access Concentrator Preparing for Hardware Installation Setting the Backplane Ethernet Segment Page Page Installing the Module into the Hub Page Page Page Testing the Installation LED Indicators Connecting a WAN Interface Page Connecting a Service Port Terminal Connecting the Terminal Page Initial Setup and Using the ROM Monitor Remote Access Concentrator Parameters Initializing the Remote Access Concentrator Page Page Page Booting the Remote Access Concentrator Auto-initializing the IP Address Parameters Page Page Manually Initializing the IP Address Parameters Booting Using BFS Page Booting Using TFTP 3. Issue the followingcommands to prepare the tftp dump file. 4. Enter the bootcommand. The boot command displaylooks similar to this: and the following message is displayed: Self-booting the Remote Access Concentrator Booting from a Windows NTHost Booting from Another Model 5399 Remote Access Concentrator Installing the Operational Software and Loading the Image Installing to and Loading from a UNIX Host Invoking the Console Monitor Chapter 3 ROM Monitor Commands T Command Descriptions Page addr The addr command display looks similar to this: The addr -d command display looks similar to this: Page Page boot Page Thestatus word ! ~XXXX~, where XXXX arefour hexadecimal digits, decodes as follows: The lowest nibble(bits 3 to 0) are a count of collisions during this transmission. For example: The boot command display (using bfs) looks similar to this: The next exampleshows a self boot. Page 3-13 Chapter 3 ROMMo nitor Commands NortelNetworks 5399 Access Switch HardwareInstallation Guide config erase Page image lat_key net ping ports sequence Page stats Page Page Chapter 4 TroubleshootingProcedures T Front Panel Alarms and LED Indicators Page Page Power-up and Boot Procedures Page Page Boot Failures Boot Error Report Page Correcting Remote Access Concentrator Parameters Load Server Host Not Responding Page Page Page Remote Access Concentrator Dumps Page Conditions for Replacing a Module Module Configuration Management Page Preparing for a Hot Swap Page Removing a Module Completing the Hot Swap Appendix A Port Pins and Signals T WAN Interface Ports 1 8 Page Appendix B Modem Upgrade Instructions T Contents of the Kit Required Tools Module Removal Instructions Modem Card Installatio n Instructions Page Removing Modem Cards Page Index A B C D I L M N O R S T U V W