Server will | Nortel Networks NN44200-300 manual

50Chapter 5 Installing the server and connecting the peripheral devices

2Locate the MAC address label on the back of the chassis that identiﬁes the ELAN controller MAC address.

3Record the MAC address on the Conﬁguration Wizard worksheet that is provided in the Installation and Conﬁguration Task List (NN44200-306).

You need the MAC address to identify the ELAN when running the Conﬁguration Wizard to conﬁgure the CallPilot server.

4Connect an RJ-45 network cable from the ELAN hub or switch to the ELAN connector on the server.

Note: The ELAN hub or switch is optional if you use a cross-over network cable to make a direct point-to-point connection from the server to the switch. However, if you choose to establish a direct point-to-point ELAN connection, no other device can connect to the ELAN.

5At the switch, connect the ELAN network cable to an MAU (Ethernet) transceiver for a Meridian 1, or to the RJ45 ELAN connector for a CS1000. Then complete the connection from the transceiver to the switch.

DANGER

MAU model NTRH9069 is not suitable for installation in ducts, plenums, or other spaces used for environmental air. Do not install it above a false ceiling or below a raised ﬂoor, unless it can be conﬁrmed that these spaces are not used to convey environmental air.

—End—

What is next?

the server will

THEN

be connected to the Nortel server subnet

continue with "Connecting the server to the Nortel server subnet (optional)" (page 51)

not be connected to a Nortel server subnet

continue with installing the software feature dongle. See "Installing the Nortel software feature dongle" (page 52).

Nortel CallPilot

1002rp Server Hardware Installation

NN44200-300 01.01 Standard

5.0 23 February 2007

Copyright © 2007, Nortel Networks

Nortel Networks Conﬁdential

Image 50

Nortel Networks NN44200-300 manual Server will

Contents

1002rp Server Hardware Installation Trademarks Japan Vcci statement Information for JapanJapan Denan statement Page Publication History February Publication History Contents Contents Getting help over the phone from a Nortel Solutions Center Getting help from the Nortel Web site Getting help through a Nortel distributor or reseller This chapter Server featuresServer dimensions and weight Introduction Front panel features front view without the front bezel Environmental speciﬁcations Alarm board Rear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot assignments Reference Documents 1002rp server description Slot deﬁnition and slot numbering T1/SMDI Network connectivity BRD20 Sample network setup Meridian Sample network setup Communication Server Meridian 1 or Communication Server 1000 systems Switch connectivityCallPilot Elan subnet and Nortel server subnet setup Network requirements Remote access connectivity Supported peripheral devices DeviceDescription Installation overview Installation checklist Preparing for installation Conventions for warnings Unpacking the 1002rp server To unpack the equipment To remove the front bezel What is next?Removing the front bezel and server cover To remove the server cover Remove the front bezel see To remove the front bezel Inspecting the server interior To inspect the server interior To replace the front bezel after installation is complete Installation and Configuration End Preparing for installation Equipment handling guidelines Safety precautionsSafety information AC versus DC systems Installing the second power supply module AC or DCAbout the power supply module To install the power supply module DC wire gauge tables AWG Metric wire conversion DC rack cabling Power supply installation Rack power and grounding PDU power and grounding About the power distribution unitDC power distribution rationale Multiple PDUs PDU terminal blocks and wiring diagram DC power input Bringing power and ground into the PDU To bring DC power and ground into the PDU Installing the server To install the server Required equipment Modem DIP switchesPreparing the modem To set the modem DIP switches DIP Continue with Connecting peripherals to the server Connecting peripherals to the server To connect the modem to the server To connect the server to the Elan subnet Connecting the server to the Elan subnetMedia Access Control address Server will Connecting the server to the Nortel server subnet optional To connect the server to the Nortel server subnet Requirements Installing the Nortel software feature dongleTo install the software feature dongle Connecting the server to power Before you begin To connect the 1002rp AC server to power Plug the server AC power cord into the server rear panel To connect the 1002rp DC server to power To start the server Copyright 2007, Nortel Networks Ferrites secured to an external cable Index Index Tlan Index Page 1002rp Server Hardware Installation