Onkyo TX-DS656 instruction manual Learning new control codes, To erase all the learned commands

Using the other remote controller functions with the supplied remote controller

SENDING/	SENDING/		SUBROOM		A/B-SUBROOM/
LEARNED	LEARNED		A B LEARN
					LEARN switch
indicator	POWER	SLEEP DIMMER	TEST	SUR
			TONE	MODE
		SOURCE SELECTOR		MULTI-CH
	DVD	VIDEO-1 VIDEO-2	VIDEO-3	INPUT
	TAPE-1 TAPE-2 TUNER		PHONO	C D
	PROGRAMMABLE AREA TV/ VIDEO				PROGRAMMABLE
	POWER	C H	VOLUME
	POWER			TV/ VCR	AREA TV/VIDEO
			TUNER		buttons
		GROUP	PRESET
	DISC	C D	TAPE
	SUBTITLE	DVD
	ON / OFF
		PAUSE	CH SEL
		/ STEP
	CURSOR
		ENTER	LEVEL	VOLUME
			MUTING
			/ REMOTE
			SPEAKER
	REMOTE CONTROLLER		RC-373M

4

1,6

2

3

5 to 10 cm

(2 to 4 inches)

1		SUBROOM
	A B LEARN

Switch to LEARN

1		SUBROOM
	A B LEARN

Switch to LEARN

VOLUME

2 POWER

The remote controller supplied with the TX-DS656 can learn functions available with other compo- nent's remote controllers.

The control codes for Onkyo cassette tape decks and CD players are already available with the supplied remote controller.

SENDING/LEARNED indicator

This indicator lights when the remote controller is transmitting a control command or learning other controller's functions. If the indicator does not light, replace the batteries.

A/B-SUBROOM/LEARN switch

A:Select this position to use the remote controller in the main

room.

B-SUBROOM:Select this position to use the remote controller in the sub-room.

LEARN: Select this position to have the supplied remote controller learn another remote controller's functions.

PROGRAMMABLE AREA TV/VIDEO buttons

Use these buttons to have the supplied remote controller learn another remote controller's function.

For TV: Power ON/OFF (POWER) and Channel selection (aCHs).

For VDP: Power ON/OFF (POWER), Playback (s), and Stop (e)

For VCR: Playback (s), Stop (e), Rewind (d), and Fast Forward (f)

Learning new control codes

1.Set the A/B-SUBROOM/LEARN selector switch to LEARN.

2.Place the head of your existing remote controller 2-4 inches (5-10 cm) from the head of this remote controller, laying both units on a table or another flat surface.

3.Press a button in the PROGRAMMABLE AREA of this remote controller to which you want to transfer the code.

The SENDING/LEARNED indicator lights.

4.Hold down the button for the function you want to transfer on the other remote controller until the SENDING/LEARNED indicator turns off.

5.Repeat steps 3 and 4 until all the required function are trans- ferred to the supplied remote controller.

6.Set the A/B-SUB ROOM/LEARN selector switch back to A.

Note:

•Some remote controllers use a single button to change codes, with the code changing each time the button is pressed. If you are using this type of controller, perform "learn" operations for each function individually, one function to one button on this remote controller.

•This remote controller transmits codes using infrared rays and can memorize the codes of other remote controllers that also use an infrared system; however,

depending on the system, there may be some rare occasions when memoriza- tion is not possible.

Changing the learned commands

Perform the whole procedure described in "Learning new control codes". The existing commands on the supplied remote controller are replaced with the newly learned commands.

To erase all the learned commands

1.Set the A/B-SUB ROOM/LEARN selector switch to LEARN.

2.While pressing the POWER button, hold down the VOLUME u button until the SENDING/LEARNED indicator turns off. All the commands stored in programmable area have been erased.

45