Panasonic AJ-HDX400E 4, 3

Chapter 4

Adjustments and settings for recording

50

4-9-2 Setup card operations

To format the setup card, save the setting data on the card or

read the saved data from the card, first perform a menu

operation to open the <CARD READ/WRITE> screen from the

FILE page.

Formatting the setup card

#

< CARD READ/WRITE >

R.SELECT :1

READ

W.SELECT :1

WRITE

CARD CONFIG

TITLE READ

TITLE:

1: ******** 5: ********

2: ******** 6: ********

3: ******** 7: ********

4: ******** 8: ********

CONFIG?

YES

#

NO

CONFIG OK

1Perform the menu operations, and display the “CARD

READ/WRITE” screen.

2Turn the JOG dial button to move the arrow (cursor) to

the CARD CONFIG item.

4To proceed with the formatting of the setup card, turn the

JOG dial button to move the arrow (cursor) to YES, and

press the JOG dial button. When the formatting of the

card is completed, the following message appears.

5Press the MENU button to exit the menu operations.

The setting menu is cleared, and the displays showing

the unit’s current statuses appear at the top and bottom of

the viewfinder screen.

<Note>

Data titles cannot be recognized when the setup card was

inserted while the CARD READ/WRITE screen was open.

Move the arrow (cursor) to the TITLE READ item, and

press the JOG dial button.

The data title is recognized, and the title is displayed.

3When the JOG dial button is pressed, the following

message appears on the screen.

If one of the following messages appears when the JOG dial button is

pressed, the card will not be formatted

Error message Remedial action

CONFIG NG NO CARD

(setup card has not been inserted)

Insert the card.

CONFIG NG ERROR

(the card cannot be formatted)

The card may be defective.

Replace it.

Saving the data settings on the card

1Perform the menu operations, and display the “CARD

READ/WRITE” screen.

2Turn the JOG dial button to move the arrow (cursor) to

the W.SELECT item and press the JOG dial button.

3Turn the JOG dial button to select a number from 1 to 8,

and press the JOG dial button.

Selecting the file No.

< CARD READ/WRITE >

R.SELECT :1

READ

#

W.SELECT :1

WRITE

CARD CONFIG

TITLE READ

TITLE:

1: ******** 5: ********

2: ******** 6: ********

3: ******** 7: ********

4: ******** 8: ********

CONFIG NG

WRITE PROTECT

Remove the card to cancel write

protect.

Contents

Main WARNING: CAUTION: CAUTION VARNING ADVARSEL! Attention/Attentie Main Power Battery (Ni-Cd Battery) Batterij Voor Primaire Voeding (Nikkelcadmiumbatterij) To remove the battery/Verwijderen van de batterij Back-up Battery (Lithium Battery) Batterij Voor Reservegeheugen (Lithiumbatterij) Contents Chapter 1 General .................................... 6 Chapter 2 Parts and their functions ....... 9 Chapter 3 Recording and playback ...... 20 Chapter 4 Adjustments and settings for recording ............................... 27 Contents Chapter 6 Maintenance and inspections ........................... 69 Chapter 7 Menu description tables ...... 77 Chapter 8 Specifications ..................... 100 1-1 Features of the camera unit E-cinema camera unit featured Progressive drive Storage type high-sensitivity function Digital zoom function 1-2 Features of the VTR unit Video camera-recorder: AJ-HDX400 1-3 System configuration 2-1 Power supply and accessory mounting section 2-2 Audio function section (input system) 2-2 Audio function section (output system) 2-3 Shooting and recording/ playback function section Shooting and recording (camera unit) Shooting and recording (VTR unit) Page 2-4 Menu operation section 2-5 Time code related section 2-6 Warning/status display section 2-7 Display window and its displays Remaining tape and remaining battery charge and audio channel level displays Displays relating to the VTR units operations and modes h D Time code-related switch settings and display items 2-8 Viewfinder section @ 8 3645 2 1 Ejecting the cassette tape Ejecting the cassette when the battery has no charge To prevent accidental erasure 2 1 2 3 4 Procedure for shooting From adjusting the white balance and black balance to stopping the recording 1 2 2 3 4 5 1 2 PRE-RECORDING function 3-5 INTERVAL REC function Procedure for shooting in the ON modes of INTERVAL REC 1 2 When recording is to be suspended at any time When the recording is to be continued When the INTERVAL REC mode is to be exited 1 2 When the recording is to be continued When the ONE SHOT mode of INTERVAL REC is to be exited Checkpoints common to all INTERVAL REC modes 3-6 RETAKE function When the RETAKE function is to be exited 3-8 Normal playback and playback at different speeds 3-7 Rec-review function <Notes> 4-1 Adjusting the white balance and black balance 1 2 3 4 5 7 When there is no time to adjust the white balance When the white balance cannot be adjusted automatically Viewfinder screen displays relating to the white balance White balance memories 4-1-2 Adjusting the black balance 1 2 4 3 4-2 Setting the electronic shutter 1 2 Viewfinder screen displays relating to the shutter 4-3 Selecting the recording signals and recording system 4-2-3 1 2 Setting the synchro scan mode Items to be set and what is set 4-4 Selecting the audio input signals and adjusting their recording levels 1 2 3 CH3 and CH4 recording levels Tape continuity with the user bits 1 2 4 5 3 User bit memory function 4-5-2 Setting the internal clocks date and time 1 2 4 5 6 8 1 2 4 3 4-5-3 Setting the time code 1 2 4 3 Time code when the battery is replaced 4-5-4 Externally locking the time code Example of connections for external locking 1 7 9 4-6-2 Basic menu operations 1 Menu displays on the viewfinder screen 4-6 4-6-1 Menu configuration 3 6 7 5 4-6-3 Selecting the user menus 4-7 Viewfinder screen status displays 4-7-1 Viewfinder lamp displays Page Page Page Page Viewfinder screen display selection 2 flashes but only for as long as this mode remains selected. JShutter speed/mode 11/. 1/60 - 1/2000 4-7-6 Setting the camera ID 4-7-5 Setting the marker displays Setting change/adjustment result messages and display modes 4-7-4 Display modes and setting changes/adjustment result messages 4-7-7 Mode check screen displays 7 9 4-8 Menu-driven function setup 4-8-1 Setting the USER SW GAIN switching 4-8-2 Selecting the video output signals Setting items and details 4-8-3 Selecting the F.AUDIO LEVEL control function 4-8-4 Allocating functions to the USER MAIN, USER1 and USER2 buttons Setting items and what is set 4-8-5 Setting the color temperature manually 4-9 Data handling Setup card 4-9-1 Handling the setup card Inserting the setup card Removing the setup card 4 Saving the data settings on the card 3 5 7 8 6 9 Loading the data saved on the card 3 13 14 5 4-9-3 How to use the user data 7 Loading the user data Writing the setting data in the user area 1 4-9-4 Reading the setting data used for the scene files How to use the scene file data Writing the setting data used for the scene files Returning the setting data used for the scene files to the factory settings 9 7 Appending titles to the setting data used for the scene files 4-9-5 How to return the menus settings to the user standard settings Operation method without performing FILE menu operations 1 2 3 4-9-7 How to use the lens file data 5-1 Supplying the power 1 To use the battery pack, there is the following choice of makes of batteries: 5-1-1 Attaching the battery and setting the battery type Using the Anton Bauer battery pack 2 1 2 3 5-1-2 Using an AC power supply When the AJ-B75 AC adapter made by Panasonic is used 1 5-2 2 3 1 GND 2, 3 4 +12V Attaching the lens and performing the flange back and white shading adjustments 1 2 3 Page Adjusting the white shading of the lens 2 1 4 3 5 6 1 2 14 3 5 Page Page 5-3-3 When using an audio component 1 2 3 1 5-4 Mounting the unit on a tripod Detaching the unit from the tripod adapter Page 5-9 Attaching the FRONT AUDIO LEVEL control knob 6-1 Inspections prior to shooting 1 3, 4 6-1-1 Preparation for inspections 6-1-2 Inspecting the camera unit 2 Page 5. Inspection using external microphones 1 2 3 4 6. Inspections relating to the time code and user bits 1 2 3 4 5 7 6-2 Maintenance 6-2-5 6-2-1 Condensation 6-2-3 6-2-2 Head cleaning Page 5. HUMID 6-3 Warning system 3. TAPE END 6-3-1 Warning description tables 1. SLACK 4. REC WARNING 6. SERVO 8. WIRELESS RF 7. RF 9. BATTERY NEAR END 10. TAPE NEAR END 1 4 5 2 3 2, 5 3 7-1 Menu configuration How to interpret the menu lists 7-2 SYSTEM SETTING 7-2-1 SYSTEM MODE 7-2-3 OUTPUT SEL 7-2-2 REC FUNCTION 7-2-4 GENLOCK 7-3 PAINT 7-3-1 ROP 7-3-2 MATRIX 7-3-3 COLOR CORRECTION 7-3-4 LOW SETTING 7-3-5 MID SETTING 7-3-6 HIGH SETTING 7-3-7 ADDITIONAL DTL 7-3-8 SKIN TONE DTL R-Y B-Y Y 7-3-9 KNEE/LEVEL 7-3-12 $CAMERA SETTINGS 7-3-11 FLARE 7-3-10 GAMMA 7-4 VF 7-4-1 VF DISPLAYS 7-4-2 VF MARKER Zebra pattern display SPOTOFFON 109% 7-4-4 VF INDICATOR1 7-4-5 VF INDICATOR2 7-4-3 USER BOX 7-4-7 !LED 7-5-2 SHUTTER SPEED 7-5 OPERATION 7-5-1 CAMERA ID If READ FACTORY DATA is selected, this setting will be cleared. 7-4-6 MODE CHECK IND 7-5-3 SHUTTER SELECT 7-5-4 USER SW 7-5-5 SW MODE 7-5-6 WHITE BALANCE MODE 7-5-7 USER SW GAIN 7-5-8 IRIS 7-6 FILE 7-6-1 CARD READ/WRITE 7-6-2 CARD R/W SELECT 7-6-3 LENS FILE 7-6-4 SCENE 7-6-5 INITIALIZE 7-7 MAINTENANCE 7-7-1 SYSTEM CHECK 7-7-2 DIAGNOSTIC 7-7-3 LENS ADJ 7-8 VTR MENU 7-8-1 VTR FUNCTION 7-7-4 BLACK SHADING 7-7-5 WHITE SHADING 7-8-2 BATTERY/TAPE 7-8-3 BATTERY SETTING1 Page 7-8-4 BATTERY SETTING2 7-8-5 MIC/AUDIO1 7-8-6 MIC/AUDIO2 7-8-8 UMID SET/INFO 7-8-7 TC/UB 7-8-9 VTR DIAG 7-9 OPTION MENU 7-9-1 OPTION 7-9-2 DOWNCON SETTING Chapter 8 Specifications [GENERAL] [CAMERA UNIT] [VTR UNIT] Video System Chapter 8 Specifications Tape Transport System [CONNECTOR SECTION] Audio Input Connectors Audio Output Connectors Video Input Connector