Manuals / Brands / Photography / Camcorder / Panasonic / Photography / Camcorder

Panasonic AJ-HDX400E 3-8 Normal playback and playback at different speeds, 3-7 Rec-review function

1 102

Download 102 pages, 2.16 Mb

Chapter 3 Recording and playback

26

3-8 Normal playback and playback atdifferent speeds

Black-and-white playback images can be viewed in the

viewfinder by pressing the PLAY button. When a color

monitor is connected to the unit’s VIDEO OUT connector and

an HD color video monitor is connected to its HD SDI

connector at the same time, the down-converted color

playback images from the VIDEO OUT connector can be

viewed on the color monitor while the HD high-quality images

from the HD SDI connector can be viewed on the HD color

video monitor.

≥In order to view these images, the OUTPUT SEL switch on

the side panel must be set to the VTR position.

In addition, when the FF and REW buttons are used, the

images can be played back at different speeds by establishing

the cue mode (PLAY + FF), review mode (PLAY + REW),

high-speed fast forward playback mode (FF) or high-speed

rewind playback mode (REW).

3-7 Rec-review function

When recording is temporarily stopped and the lens RET

button is pressed, the last two seconds of the tape are

automatically rewound, and the playback pictures on this part

of the tape appear on the viewfinder screen. This makes it

possible to check whether recording was performed properly.

After the two seconds of the tape have been played back, the

unit is again set to the recording start standby mode.

If the RET button is held down, a maximum of 10 seconds of

the tape is rewound and played back.

The RET button function can be allocated by opening the

<USER SW> screen from the OPERATION page and

selecting settings for the USER MAIN SW, USER1 SW and

USER2 SW items by performing menu operations.

<Notes>

≥The rec-review function cannot be used unless recording

lasts for one or more seconds.

≥If the OUTPUT SEL switch on the side panel is at the VTR

position during the rec-review operation, the rec-review

images are output not only to the viewfinder but to the video

output connectors (VIDEO OUT connector and HD SDI

connector) as well. Bear in mind that if back-up images are

being recorded by a backup VTR that has been connected,

these rec-review images will end up being recorded.

Direction of tape travel

Playback of recorded section

Recording section

2 to 10 sec.

No recorded or already recorded section

Rec-pause

Rec-pause

Rec-review operation

Contents

Main WARNING: CAUTION: CAUTION VARNING ADVARSEL! Attention/Attentie Main Power Battery (Ni-Cd Battery) Batterij Voor Primaire Voeding (Nikkelcadmiumbatterij) To remove the battery/Verwijderen van de batterij Back-up Battery (Lithium Battery) Batterij Voor Reservegeheugen (Lithiumbatterij) Contents Chapter 1 General .................................... 6 Chapter 2 Parts and their functions ....... 9 Chapter 3 Recording and playback ...... 20 Chapter 4 Adjustments and settings for recording ............................... 27 Contents Chapter 6 Maintenance and inspections ........................... 69 Chapter 7 Menu description tables ...... 77 Chapter 8 Specifications ..................... 100 1-1 Features of the camera unit E-cinema camera unit featured Progressive drive Storage type high-sensitivity function Digital zoom function 1-2 Features of the VTR unit Video camera-recorder: AJ-HDX400 1-3 System configuration 2-1 Power supply and accessory mounting section 2-2 Audio function section (input system) 2-2 Audio function section (output system) 2-3 Shooting and recording/ playback function section Shooting and recording (camera unit) Shooting and recording (VTR unit) Page 2-4 Menu operation section 2-5 Time code related section 2-6 Warning/status display section 2-7 Display window and its displays Remaining tape and remaining battery charge and audio channel level displays Displays relating to the VTR units operations and modes h D Time code-related switch settings and display items 2-8 Viewfinder section @ 8 3645 2 1 Ejecting the cassette tape Ejecting the cassette when the battery has no charge To prevent accidental erasure 2 1 2 3 4 Procedure for shooting From adjusting the white balance and black balance to stopping the recording 1 2 2 3 4 5 1 2 PRE-RECORDING function 3-5 INTERVAL REC function Procedure for shooting in the ON modes of INTERVAL REC 1 2 When recording is to be suspended at any time When the recording is to be continued When the INTERVAL REC mode is to be exited 1 2 When the recording is to be continued When the ONE SHOT mode of INTERVAL REC is to be exited Checkpoints common to all INTERVAL REC modes 3-6 RETAKE function When the RETAKE function is to be exited 3-8 Normal playback and playback at different speeds 3-7 Rec-review function <Notes> 4-1 Adjusting the white balance and black balance 1 2 3 4 5 7 When there is no time to adjust the white balance When the white balance cannot be adjusted automatically Viewfinder screen displays relating to the white balance White balance memories 4-1-2 Adjusting the black balance 1 2 4 3 4-2 Setting the electronic shutter 1 2 Viewfinder screen displays relating to the shutter 4-3 Selecting the recording signals and recording system 4-2-3 1 2 Setting the synchro scan mode Items to be set and what is set 4-4 Selecting the audio input signals and adjusting their recording levels 1 2 3 CH3 and CH4 recording levels Tape continuity with the user bits 1 2 4 5 3 User bit memory function 4-5-2 Setting the internal clocks date and time 1 2 4 5 6 8 1 2 4 3 4-5-3 Setting the time code 1 2 4 3 Time code when the battery is replaced 4-5-4 Externally locking the time code Example of connections for external locking 1 7 9 4-6-2 Basic menu operations 1 Menu displays on the viewfinder screen 4-6 4-6-1 Menu configuration 3 6 7 5 4-6-3 Selecting the user menus 4-7 Viewfinder screen status displays 4-7-1 Viewfinder lamp displays Page Page Page Page Viewfinder screen display selection 2 flashes but only for as long as this mode remains selected. JShutter speed/mode 11/. 1/60 - 1/2000 4-7-6 Setting the camera ID 4-7-5 Setting the marker displays Setting change/adjustment result messages and display modes 4-7-4 Display modes and setting changes/adjustment result messages 4-7-7 Mode check screen displays 7 9 4-8 Menu-driven function setup 4-8-1 Setting the USER SW GAIN switching 4-8-2 Selecting the video output signals Setting items and details 4-8-3 Selecting the F.AUDIO LEVEL control function 4-8-4 Allocating functions to the USER MAIN, USER1 and USER2 buttons Setting items and what is set 4-8-5 Setting the color temperature manually 4-9 Data handling Setup card 4-9-1 Handling the setup card Inserting the setup card Removing the setup card 4 Saving the data settings on the card 3 5 7 8 6 9 Loading the data saved on the card 3 13 14 5 4-9-3 How to use the user data 7 Loading the user data Writing the setting data in the user area 1 4-9-4 Reading the setting data used for the scene files How to use the scene file data Writing the setting data used for the scene files Returning the setting data used for the scene files to the factory settings 9 7 Appending titles to the setting data used for the scene files 4-9-5 How to return the menus settings to the user standard settings Operation method without performing FILE menu operations 1 2 3 4-9-7 How to use the lens file data 5-1 Supplying the power 1 To use the battery pack, there is the following choice of makes of batteries: 5-1-1 Attaching the battery and setting the battery type Using the Anton Bauer battery pack 2 1 2 3 5-1-2 Using an AC power supply When the AJ-B75 AC adapter made by Panasonic is used 1 5-2 2 3 1 GND 2, 3 4 +12V Attaching the lens and performing the flange back and white shading adjustments 1 2 3 Page Adjusting the white shading of the lens 2 1 4 3 5 6 1 2 14 3 5 Page Page 5-3-3 When using an audio component 1 2 3 1 5-4 Mounting the unit on a tripod Detaching the unit from the tripod adapter Page 5-9 Attaching the FRONT AUDIO LEVEL control knob 6-1 Inspections prior to shooting 1 3, 4 6-1-1 Preparation for inspections 6-1-2 Inspecting the camera unit 2 Page 5. Inspection using external microphones 1 2 3 4 6. Inspections relating to the time code and user bits 1 2 3 4 5 7 6-2 Maintenance 6-2-5 6-2-1 Condensation 6-2-3 6-2-2 Head cleaning Page 5. HUMID 6-3 Warning system 3. TAPE END 6-3-1 Warning description tables 1. SLACK 4. REC WARNING 6. SERVO 8. WIRELESS RF 7. RF 9. BATTERY NEAR END 10. TAPE NEAR END 1 4 5 2 3 2, 5 3 7-1 Menu configuration How to interpret the menu lists 7-2 SYSTEM SETTING 7-2-1 SYSTEM MODE 7-2-3 OUTPUT SEL 7-2-2 REC FUNCTION 7-2-4 GENLOCK 7-3 PAINT 7-3-1 ROP 7-3-2 MATRIX 7-3-3 COLOR CORRECTION 7-3-4 LOW SETTING 7-3-5 MID SETTING 7-3-6 HIGH SETTING 7-3-7 ADDITIONAL DTL 7-3-8 SKIN TONE DTL R-Y B-Y Y 7-3-9 KNEE/LEVEL 7-3-12 $CAMERA SETTINGS 7-3-11 FLARE 7-3-10 GAMMA 7-4 VF 7-4-1 VF DISPLAYS 7-4-2 VF MARKER Zebra pattern display SPOTOFFON 109% 7-4-4 VF INDICATOR1 7-4-5 VF INDICATOR2 7-4-3 USER BOX 7-4-7 !LED 7-5-2 SHUTTER SPEED 7-5 OPERATION 7-5-1 CAMERA ID If READ FACTORY DATA is selected, this setting will be cleared. 7-4-6 MODE CHECK IND 7-5-3 SHUTTER SELECT 7-5-4 USER SW 7-5-5 SW MODE 7-5-6 WHITE BALANCE MODE 7-5-7 USER SW GAIN 7-5-8 IRIS 7-6 FILE 7-6-1 CARD READ/WRITE 7-6-2 CARD R/W SELECT 7-6-3 LENS FILE 7-6-4 SCENE 7-6-5 INITIALIZE 7-7 MAINTENANCE 7-7-1 SYSTEM CHECK 7-7-2 DIAGNOSTIC 7-7-3 LENS ADJ 7-8 VTR MENU 7-8-1 VTR FUNCTION 7-7-4 BLACK SHADING 7-7-5 WHITE SHADING 7-8-2 BATTERY/TAPE 7-8-3 BATTERY SETTING1 Page 7-8-4 BATTERY SETTING2 7-8-5 MIC/AUDIO1 7-8-6 MIC/AUDIO2 7-8-8 UMID SET/INFO 7-8-7 TC/UB 7-8-9 VTR DIAG 7-9 OPTION MENU 7-9-1 OPTION 7-9-2 DOWNCON SETTING Chapter 8 Specifications [GENERAL] [CAMERA UNIT] [VTR UNIT] Video System Chapter 8 Specifications Tape Transport System [CONNECTOR SECTION] Audio Input Connectors Audio Output Connectors Video Input Connector