5.MENU/DIAG button

MENU button

Press this button to open the MENU. Press again to return to the previous screen.

DIAG (SHIFT+MENU) button

Press to show information about this unit. Press again to return to the previous screen. However, this function is not available while thumbnails or play lists are displayed.

Information about this unit include [HOURS METER], [WARNING], [UMID] and [DIF]. Use the SET button to switch among them.

[WARNING]:

Shows warning

 

information.

 

 

[HOURS METER]:

Shows the unit serial

 

number, the number of

 

hours it has been on, and

 

the number of times it has

 

been switched on and off.

 

 

[UMID]:

Shows UMID information

 

for the current video.

 

 

[DIF];

Shows various information

 

on the current DIF (the

 

IEEE 1394 interface).

 

 

6.IN/SLOT CLIP/PF1 button

Use these functions to create play lists. Press the ENTRY button and this button simultaneously when registering an event (when the PLAY LIST button and the EVENT button are both on) to set an event IN point. Hold down this button and press the RESET button to cancel the IN point of the selected event.

➝Refer to the Section “Using Play List” (page 61).

•Press the SHIFT button and this button simultaneously while thumbnails are displayed to switch the clip display between SELECTED and specific SLOT.

•Press the ENTRY button and this button simultaneously when the PLAY LIST button is off to register a cue-up point.

•Press this button after the PF button when the THUMBNAIL and PLAY LIST buttons are off to obtain access to the setup menu registered using the PF1 button.

7.TRIM–/SLOT SELECT– button

Hold down the IN, OUT, or SPLIT button and press this button in the play list mode to shift the IN, OUT, or SPLIT point 1 frame forward.

Hold down the SHIFT button and this button simultaneously when the PLAY LIST button is off to

move to the previous recording slot position.Pressing this button when the unit is in slot 1 results in a move to slot 6.

8. ENTRY/CLIP (LIST/PF2 button)

Use these functions to create play lists.

 

Pressing the IN, OUT or SPLIT button simultaneous

 

 

with this button while registering an event (the PLAY

Introduction

LIST and EVENT buttons are on), allows you to set the

 

IN, OUT and SPLIT points.

 

• Pressing the SHIFT button simultaneous with this

 

button in the play list mode allows you to add a clip

 

selected from a thumbnail display to the play list.

 

• Press this button after the PF button when the

 

THUMBNAIL and PLAY LIST buttons are off to obtain

 

access to the setup menu registered using the PF2

 

button.

 

9. TRIM+/SLOT SELECT+ button

 

Hold down the IN, OUT, or SPLIT button and press this

 

button in the play list mode to shift the IN, OUT, or

 

SPLIT point 1 frame backward.

 

While the PLAY LIST button is off, hold down the SHIFT

 

button and this button simultaneously to move to the

 

previous recording slot position. Pressing this button

 

when the unit is in slot 6 results in a move to slot 1.

 

10.OUT/ALL CLIP/PF3 button

 

Use these functions to create play lists. Press the

 

ENTRY button and this button simultaneously when

 

registering an event (when the PLAY LIST button and

 

the ENTRY button are both on) to set an event OUT

 

point.

 

Hold down this button and press the RESET button to

 

cancel the OUT point of the selected event.

 

➝For details, refer to “Using Play List” (page 61).

 

• Press the SHIFT button and this button

 

simultaneously while thumbnails are displayed to

 

return the clip display to ALL.

 

• Press the ENTRY button and this button

 

simultaneously when the PLAY LIST button is off to

 

register a cue-up point.

 

• Press this button after the PF button when the

 

THUMBNAIL and PLAY LIST buttons are off to obtain

 

access to the setup menu registered using the PF3

 

button.

 

11.SHIFT button

 

Use this button together with the FF, REW and SET

 

buttons.

 

Introduction: Control Reference Guide 21