Tally settings, „„Settings on remote cameras | Panasonic AWRP120GJ

Tally settings

The unit can receive the tally information of the switcher and other external devices from the TALLY/GPI connector (TALLY input) on the rear panel and two network lines.

To enable turning on the camera status indicators on the unit and the tally lamps on the remote cameras based on the received tally information, you need to configure the following settings.

Registering the camera numbers that will correspond to the tally inputs

Setting is required to use TALLY IN1 to TALLY IN10 signals from the TALLY/GPI connector (TALLY input) on the rear panel.

Refer to the relevant explanation in this section.

Registering the camera numbers that will correspond to the image inputs of the switcher

Setting is required to use tally information received via the network. Refer to “Setting linking with a switcher” (page 31).

Setting the sending of tally information from the unit to remote cameras

Refer to the relevant explanation in this section.

Settings on remote cameras

Setting is required on the remote camera to enable turning on the tally lamp.

Refer to the operating instructions for the remote camera.

Registering the camera numbers that will correspond to the tally inputs

1. Press the MENU button..

2. Open TALLY menu [44]..

3. Turn the F1 dial to select the TALLY input connector number..

1.TALLY IN1

CAM1

Input connector number : Select form TALLY IN1 to TALLY IN10

4.Turn the F2 dial to select the corresponding camera number, and then press the F2 dial to confirm the selection..

Camera number : Select from CAM1 to CAM100.

Setting the sending of tally information from the unit to remote cameras

1.Press the MENU button..

2.Open CAMERA SETUP menu [24]..

3.Turn the F1 dial to display the “3.  TALLY OUT” item..

3.TALLY OUT

Off

4.Turn the F2 dial to select “On” or “Off”, and then press the F2 dial to confirm the selection..

On	: Sends tally information to remote cameras.
Off	: Does not send tally information to remote cameras.

39

Image 39

Panasonic AWRP120GJ operating instructions Tally settings, „„Settings on remote cameras, Tally IN1, Tally OUT

Contents

Operating Instructions Illustrations and screen images in this manual About trademarks and registered trademarksCopyrights Abbreviations Contents How to turn on the power of the remote cameras How to turn on and off the power of the remote cameras „„Turning off the power of all the cameras How to turn off the power of the remote camerasTurning off the power one camera at a time Turning off the power of multiple cameras Bars button Making image adjustments for the selected remote cameraColor adjustment section ZzR and B pedestal Automatically adjusting the white balance Setting the gainSetting the pedestal Setting the white balance Automatically adjusting the black balance Setting the black balanceManually adjusting the white balance R and B gain settings Auto tracking white adjustment ATW Setting the shutter speed Setting the detailAdjusting the shutter speed Setting the shutter mode AW‑HE50 Setting the shooting mode Scene 1 to Scene Selecting an ND filter with the User buttons User 1 to User Setting an ND filterND Filter ND1 Operate the OSD menu Hold down the Camera OSD button to turn on its indicatorHold down the Camera OSD button to turn off its indicator Operating the osd menu of a remote camera Pmem Operating preset memory PmemZzLighting of number button indicators ZzChanging pages Registering preset memory Store Recalling preset memory RecallDeleting preset memory Delete Iris Scope Mode aScope settings and recalled items Recalled item Setting Speed PM GRP1 Mode Separate Operating preset memory groups Pmem GroupSetting the operation mode SEPARATE/ ALL Creating preset memory groups Pressing a button to recall a preset memory group Recalling preset memory groupsRegistering the preset memory to recall when in ALL mode PM GRP1 Mode ALL 3m50s Remained Operating tracing memory TmemRegistering tracing memory Store CAM1 Tmem Press Stop button Recalling tracing memory RecallStandby Recall Recalling Restoring Restoring tracing memory RestoreStandby Restore Deleting tracing memory Delete Recalled item Setting Setting the items to recall when recalling tracing memory T Curv Configuring the remote camera operation settingsSetting the PAN/TILT lever inclination and speed „„Operation of Speed dial Setting the zooming direction Setting the pan, tilt, zoom, and focus operation directionsSetting the panning direction Setting the tilting direction Speed with Z Off Setting the minimum lens zoom start speedSetting the focusing direction MIN Speed Setting procedure „„When AW-HE50, AW-HE60, or AW-HE120„„When other remote camera Controlling a heater or fan Returning a remote cameras to its home positionControlling a defroster Controlling a wiper Button indicator on or blinking Configuring the unit operation settingsEnabling or disabling operation with the Enable buttons Press the Enable button Enabling or disabling menu operation Disabling Menu operationEnabling Menu operation LCD Backligh T Off Switching the focus operation and iris operationSetting the LCD panel backlight FOCUS/IRIS Standard USER1 Assigning functions to the User buttons INPUT1 Setting linking with a switcher„„Settings for the connection between unit and switcher „„Settings on the switcher BUS AUX Buscont functionEnabling or disabling the Buscont function Buscont Enabling or disabling the Camera Select function Setting the Focus Assist functionFocus Assist function Camera Select view function T/Z Control CAM Tally IP functionEnabling or disabling the Tally IP function Tallyip CAM INF Caminfformat CAM INF AlarmCAM INF function Enabling or disabling the CAM INF function Load Memory card operationsZzMemory cards Save Saving data to a memory card Save Initializing a memory card Init Deleting the files saved to a memory card Delete Loading data from a memory card Load Tally OUT Tally settings„„Settings on remote cameras Tally IN1 Checking alarm information Displaying alarm informationPower No Alarm ALL Setup Returning the unit to the factory default state InitializeSetting items stored on the unit Setup Returning the unit to the factory default state Setting items stored on the unitInitialize ALL AW‑RP120 CAM OUT1 Registering camera numbers to CAM OUT1 to CAM OUT10 Installing the software Setup Software Enter the IP addresses in the IP address boxes Registering the unit in Setup Software Settings for connecting with the remote cameras and switcher Displaying the Setting tab Initializing the IP addresses Executing auto IP settingAcquiring the connection settings Changing the connection destination IP addresses Setting user authentication Enter the same password as above in the Retype password boxClicking Refresh clears the user name and password Campinp POS Campinp ModeOperations of AW-HE2 Campinp CTL Dial/button Setting item Remote camera Table of setting items dedicated dials and buttons Table of setting items menus VideoFilm Table of setting items menus SW Setup SW CTL Operation lock When starting up and switching camera groupsPreset memory Messages IP connection settings Memory cardMessages Xx Menu Index Index プロフェッショナルAVビジネスユニット