Parts and their functions (continued)
Rear panel
| TC | HD/SD REF IN | VIDEO OUT |
|
|
|
| |
HD/SDI | IN |
| 1 | Y | PB |
|
|
|
|
|
|
|
|
|
|
| |
IN |
|
|
|
|
|
|
|
|
|
|
|
|
| PR |
|
|
|
OUT1 |
|
|
|
|
|
|
|
|
AUDIO OUT | OUT |
| 2 |
|
|
|
|
|
| AUDIO IN | (SUPER) |
|
|
|
|
| |
|
|
|
|
|
|
| ||
PUSH CH1 | PUSH CH2 | CH1 | CH2 | AUDIO | L |
|
|
|
OUT2 |
|
|
| MON |
|
|
|
|
|
|
| OUT |
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| DC OUT |
| AC IN |
|
|
|
|
|
| 12V 250mA |
|
|
SD/SDI |
|
|
|
| R |
|
|
|
PUSH |
|
|
|
| R | FUSE 250V T2.5AH |
|
|
PUSH |
|
|
| E |
|
| ||
|
|
|
|
| MO | F1 |
|
|
DVCPRO |
| ENCODER |
|
| R |
|
|
|
/DV |
|
|
| T |
|
|
| |
| REMOTE |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
L | R |
|
|
|
|
|
| SIGNAL |
MONITOR |
|
|
|
|
|
| DC IN | GND |
|
|
|
|
|
|
|
| |
AC IN inlet
This is the AC power inlet.
Connect the accessory power cable here.
When both an AC power supply and DC power supply have been connected, the AC power supply takes priority.
DC IN socket
This is the input connector for the DC 12V supply voltage.
Use an external DC power supply rated at DC 12 V/7 A (12 A peak or higher)
When the voltage has dropped to around 10.6V, the unit’s power is automatically turned off. (When
Even when the supply voltage is restored later, the power will not automatically come back on. The POWER switch must be set to OFF and then back to ON several seconds later.
| Pin No. | Signal | |
1 | 1 | Ground | |
2 | 2 | – | |
3 | |||
3 | – | ||
4 | |||
| 4 | +12 V |
External DC adapter
If an external DC power supply is used, then check the ratings of the external DC power supply so that they are compatible with those of this unit. Check the pin arrangements of the DC output terminal of the external DC power supply and those of the DC IN socket of this unit so that their polarities are correctly arranged.
If +12 V are supplied to the unit’s GND terminal by mistake, this may cause fire or injury.
If the polarities of the DC IN connectors of other devices are incorrect, and the other devices are connected to the unit by mistake, fire or personal injury may result.
<Notes>
zIf an external DC power supply is used, then make sure that the external DC power supply is first turned ON, then this unit is turned ON. Improper operation may result in a malfunction in the unit due to slow startup of the output voltage of the external DC power supply.
zIf input exceeds 18 V by mistake, the protection feature shuts down the power source at around 20 to 35 V. Change the voltage to the regular voltage, and the unit is available. An AC source cannot be connected to this terminal.
DC OUT socket
This is the DC 12V output socket.
Power is supplied from here to the external remote controller
The DC power cable is packed together with the AJ- A95.
|
| Pin No. | Signal | |
|
| 1 | Ground | |
2 | 3 | 2 | – | |
1 | 4 | |||
3 | – | |||
|
| |||
|
| 4 | +12 V |
Fuse holder
This holds the AC 250 V/2.5 A fuse (time lag type).
<Note>
Use the fuse specified by Panasonic.
14