Panasonic AJ-HD1400E, J-HD1400P manual 62

Error messages (continued)

Warning messages (continued)

Priority	Monitor display	Description	Corrective action	VTR operation
	E-00	This appears when the servo is not locked for three or		Operation
	(SERVO NOT		Check the tape.
		more seconds during playback or recording.		continues.
	LOCKED)
		(In 23.98/24 Hz mode)
		Display when the time code is recorded in DF mode. On
	E-93	the drop point of the time code, the video output is	Use the original tape recorded
		garbled and audio output is muted.		Operation
	(INVALID TC	Operation of VTR continues.	with the variable frame rate	continues.
	MODE)		camera.
		When using this unit to playback a tape recorded from a
		variable frame rate camera, it is necessary to record the
		time code in NDF mode.
		(In 23.98/24 Hz, 25 Hz, 50 Hz mode)
		Appear when the relationship between the active frame
		information and time code is not regular during playback.
	E-94	The video output may not be regular (not smooth).	Use the original tape recorded
		Operation of VTR continues.		Operation
	(TC SEQUENCE	The active frame information (top frame of the switched	with the variable frame rate	continues.
	UNMATCH)		camera.
		frame image) is recorded on the tape from a variable
		frame rate camera. To play it back with this unit, it is
		necessary to detect the 0 frame of the time code at the
		activation frame position.
	E-01	This appears when an envelope level approximately one-		Operation
		third of the normal level has been detected for more than	Clean the video heads.
	(LOW RF)			continues.
		one second during playback or recording.
	E-02	This appears when the error rate has increased to the		Operation
	(HIGH ERROR	extent that correction or interpolation was applied to	Clean the video heads.
				continues.
	RATE)	either the video or audio playback signals.
Low

Error messages

Monitor display	Description	Corrective action	VTR
			operation
	The unit switches to eject mode and if the cassette fails to move up
E-29	within 6 seconds, this error number flashes on the display.
	<Note>	Set the POWER switch to OFF
FRONT LOAD			STOP
MOTOR	If the cassette does not move down inside the machine even when 6	and then to ON again.
	seconds have elapsed since the cassette was inserted, the VTR is
	transferred to the eject mode.
	If the unloading operation is not completed within 6 seconds, this
E-31	error number flashes on the display.	Set the POWER switch to OFF
	<Note>		STOP
LOADING MOTOR	When the loading operation is not completed within 6 seconds, the	and then to ON again.
	VTR is transferred to the eject (unloading) mode.
E-35	If there is no response from the servo microcomputer for 1 second	Set the POWER switch to OFF
SERVO CONTROL			STOP
ERROR	or more, this error number flashes on the display.	and then to ON again.
E-37	If 10 seconds or more elapses and the servo microcomputer has not	Set the POWER switch to OFF
SERVO COMM	followed orders issued by the system control microcomputer, this		STOP
ERROR	error number flashes on the display.	and then to ON again.
E-38	This appears when the automatic reel and capstan rotation	Set the POWER switch to OFF
	adjustment, which is performed in the EJECT mode, has not been		STOP
SERVO FG ERROR	carried out properly when the unit’s power was switched on.	and then to ON again.
E-51	If the take-up reel rotates without engaging for a specific period of	Set the POWER switch to OFF
FRONT LOAD	time during the start or end processing operation while loading is		STOP
ERROR	underway (half position), this error number flashes on the display.	and then to ON again.
E-52	If the take-up reel fails to take up the tape while the tape is traveling
	in the state where the total amount of the tape has not yet been	Set the POWER switch to OFF
W-UP REEL NOT			STOP
ROTA	detected after the cassette was inserted, this error number flashes	and then to ON again.
	on the display.
	If there is an abnormally large discrepancy between the amount of
E-53	tape taken up by the take-up reel and the amount of tape supplied	Set the POWER switch to OFF
	by the supply reel while the tape is traveling after the total amount of		STOP
WINDUP ERROR	the tape begins to be detected, this error number flashes on the	and then to ON again.
	display.

62