Setup menus (continued)

TAPE PROTECT

No./Item

 

Description of setting

 

 

400

For setting the time to be taken before the unit is set

STILL TIMER

in the tape protection mode when it is left standing in

 

the STOP or STILL status.

 

(Units: S = seconds, min = minutes)

 

0000

0.5S

 

0001

5S

 

0002

10S

 

0003

20S

 

0004

30S

 

0005

40S

 

0006

50S

 

0007

1min

 

0008

2min

 

<Note>

 

 

When a DV, DVCAM or an unused tape is used, or a

 

DVCPRO HD/DVCPRO50/DVCPRO tape is used in

 

the EE mode, any setting above 2 (10S) will result in

 

a setting time of 10 seconds.

 

 

401

For setting the operation to be performed in the tape

SRC

protection mode when the unit is left standing in the

PROTECT

STILL status (JOG/VAR/SHTL).

 

0000

STEP :

 

STEP FWD

 

0001

HALF :

 

STANDBY OFF (HALF LOADING)

 

<Note>

 

 

When STEP FWD is selected, the unit is

 

automatically transferred to the standby OFF (half

 

loading) mode when the unit is left standing in the

 

STOP mode for a total of 30 minutes (or 1 minute for

 

DV or DVCAM tape).

 

 

402

For setting the cylinder operation in the standby OFF

DRUM

(half loading) mode.

STDBY

0000

OFF

 

The cylinder stops rotating.

 

0001

ON

 

The cylinder continues to rotate.

403For setting the operation to be performed in the tape

STOP protection mode when the unit is left standing in the

PROTECT STOP status.

0000

STEP :

STEP FWD

0001

HALF :

STANDBY OFF (HALF LOADING)

<Note>

 

When STEP FWD is selected, the unit is

automatically transferred to the standby OFF (half

loading) mode when the unit is left standing in the

STOP mode for a total of 30 minutes (or 1 minute

for DV or DVCAM tape).

“_____” indicates the factory setting.

TIME CODE

No./Item

 

 

Description of setting

 

 

 

500*1

For setting whether to output the VITC signal at the

VITC BLANK

position which is set using menu items No.501 VITC

 

POS-1 and No.502 VITC POS-2.

 

 

0000

BLANK :

 

 

 

The VITC signal is not output.

 

 

0001

 

THRU :

 

 

 

The VITC signal is output.

 

 

<Note>

 

 

 

 

 

This setting takes effect only with the SD output

 

(analog composite output and SD SDI output).

 

 

501*1*2

For setting the position where the VITC signal is to be

VITC POS-1

inserted.

 

 

<625 mode>

 

 

<525 mode>

 

 

 

0000

 

10L

0000

7L

 

:

 

:

:

:

 

0006

 

16L

0004

11L

 

:

 

:

:

:

 

0010

 

20L

0015

22L

 

<Notes>

 

 

 

 

 

z The same line as the one selected by menu item

 

No.502 VITC POS-2 and No.692 UMID POS

 

cannot be selected.

 

 

 

z This setting takes effect only with the SD output

 

(analog composite output and SD SDI output).

 

 

502*1*2

For setting the position where the VITC signal is to be

VITC POS-2

inserted.

 

 

<625 mode>

 

 

<525 mode>

 

 

 

0000

 

10L

0000

7L

 

:

 

:

:

:

 

0008

 

18L

0008

13L

 

:

 

:

:

:

 

0010

 

20L

0015

22L

 

<Notes>

 

 

 

 

 

z The same line as the one selected by menu item

 

No.501 VITC POS-1 and No.692 UMID POS

 

cannot be selected.

 

 

 

z This setting takes effect only with the SD output

 

(analog composite output and SD SDI output).

 

 

503*1

For setting the synchronization of the internal time

TCG MODE

code generator.

 

 

 

0000

 

SW :

 

 

 

When the TCG switch on the front panel is set to

 

REGEN or PRESET, the selection is complied.

 

0001

 

AUTO :

 

 

 

REGEN or PRE is automatically selected

 

depending on the operation mode.

 

 

When editing (including a chained shot):

 

REGEN is selected.

 

 

 

Other than the above: PRE is selected.

 

 

504*1

For setting the operation mode in which the internal

RUN MODE

time code generator runs.

 

 

 

0000

 

REC :

 

 

 

The generator runs only while recording is in

 

progress.

 

 

 

0001

 

FREE :

 

 

 

The generator runs while the power is on

 

regardless of the unit’s operation mode.

 

 

505*1

For setting the signal to be regenerated when the

TCG REGEN

TCG (time code generator) is in the regeneration

 

mode.

 

 

 

 

 

0000

TC&UB :

 

 

 

Both the time code and user bits are regenerated.

 

0001

 

TC :

 

 

 

Only the time code is regenerated.

 

 

0002

 

UB :

 

 

 

Only the user bits is regenerated.

 

 

 

 

 

 

 

*1 Displayed menus may vary depending on the settings in menu No. 25 SYSTEM FREQ. For details, refer to “Menus which are displayed” (page 32).

*2 Even if the RESET button is pressed while pressing the SEARCH button, the value may not return to the factory setting.

45