Panasonic AJ-HD1400E, J-HD1400P (continued), Displaying the warning information

Error messages (continued)

Displaying the warning information

zA warning message appears when a warning has occurred. “NO WARNING” appears when a warning has not occurred.

zWhen more than one warning has occurred simultaneously, move the joystick up or down to check the description of each warning.

Warning messages

Priority	Monitor display	Description	Corrective action	VTR operation
High		If condensation is detected, the error number flashes and
		the unit transfers to eject mode. The drum rotates after
		the cassette is ejected to eliminate the condensation.
		Once the unit is released from condensation status, the
	E-20	error message display is cleared and the VTR is able to
		be used.	Leave the power on and wait.	EJECT
	(DEW)
		z If condensation is detected in the eject mode, the drum
		starts rotating as soon as it is detected.
		z If condensation is detected when the cassette has
		been inserted, the drum rotation is stopped, and after
		the tape is ejected, the drum starts rotating.
	E-95	(When “SLTC” is selected in menu No. 032 REC REF)
		Appear when a time code for a signal input into the HD	Check the time code	Operation
	(INVALID	SDI IN connector is not stepping at the standard rate in
			information of the input signal.	continues.
	EMBEDDED TC)	synchronizing the image frames to be recorded with the
		time code.
			If the cable connection is in	Signal input
	E-92		loop status, reconnect to 1 to	and output
		Display if the IEEE1394 digital interface connection status	1.	through the
	(1394 INITIAL
		is irregular	If not using the loop	IEEE1394
	ERROR)
			connection, turn the POWER	digital interface
			switch OFF > ON.	is stopped.
	E-04	This appears when the signals supplied from the	Check that the 1394 input has	No recording o
	(UNKNOWN SIG)	IEEE1394 digital interface are not DVCPRO/DV format	been connected properly.	perations are
		signals.		possible.
	E-90	This appears when the initialization process fails during	Check the input signal.	Operation
	(NOT 1X 100M SIG)	communication via the IEEE1394 digital interface.		continues.*1
		This appears when the compressed video signals
	E-16	supplied from the IEEE1394 digital interface are irregular	Check the 1394 input signals.It	Operation
		signals.	is possible that playback
	(INVALID VIDEO
		z This warning appears only during recording operations.	signals of an unrecorded tape	continues.*1
	SIG)
		In such cases, no signals are recorded on the tape,	are being input.
		and only erasure of existing signals is performed.
	E-17	This appears when the audio signals supplied from the	Check the 1394 input signals.It
		IEEE1394 digital interface are irregular signals.	is possible that signals other	Operation
	(INVALID AUDIO	z This warning appears only during recording operations.	than 1x playback signals are
				continues.*2
	SIG)	In such cases, the signals are recorded with the audio	being input from a VTR or
		signals muted.	other device.
		This appears when the time code information supplied
	E-18	from the IEEE1394 digital interface is irregular	Check the time code of the	Operation
		information.
			device which is supplying the
	(INVALID TC SIG)	z This warning appears only during recording operations.		continues.*3
		In such cases, the internally generated time code is	time code.
		recorded.
	E-14	This appears when the signals supplied to the IEEE1394		Operation
		digital interface are at variance from the system format	Check the input signal.
	(NO MATCH SIG)			continues.*1
		which is set by this unit.
	E-10	This appears when the fan motor has shut down.	Check the fan for foreign	Operation
		z The power automatically turns off if 5 minutes pass with
	(FAN STOP)		matter.	continues.
		the fan stopped.
		This appears when a blank section lasting for more than
		one second on the tape has been detected during
	E-09	playback.	Check the tape. It is possible
		A blank section is identified as such when all the following		Operation
	(NO RF)	conditions are met:	that an unrecorded tape has	continues.
			been loaded.
		z There are no output signals from any of the heads.
		z The playback data cannot be read.
		z There is no CTL signal (DV/DVCAM tapes excluded).

*1 This error message always appears in the EE mode.

In such a case, black signals are recorded as the video signals, and the audio signals are muted. *2: This error message always appears in the EE mode.

In such a case, the audio signals are muted.

*3: This error message always appears in the EE mode.

In such a case, the time code of the time code generator inside this unit is recorded as the time code signal.

61