Setup menus (continued)

BASIC (continued)

No./Item

 

Description of setting

 

 

030*1

For setting the field frequency.

HD

0000

59/23 :

The field frequency is set to 59.94/23.98 Hz.

FREQUENCY

0001

60/24 :

 

The field frequency is set to 60/24 Hz.

 

<Note>

 

 

The field frequency which is set here takes effect only

 

when there is no input which supports the OUT REF

 

setting.

 

 

If there is an input which supports the setting, the

 

field frequency is consistent with the field frequency

 

of input.

 

 

 

031*1

For selecting the video output reference.

OUT REF

0000

AUTO :

The REF signal (HD/SD) which is input to the REF

 

 

connector is automatically identified and serves as

 

the reference.

 

If no signal is supplied to the REF connector, the

 

HD serial input signal serves as the reference.

 

If neither the REF input signal nor HD serial input

 

signal is supplied, the unit’s internal reference is

 

used.

 

 

0001

INPUT :

 

The input signal serves as the reference.

 

If this signal is not available, the unit’s internal

 

reference is used.

 

0002

HD REF :

 

The HD REF input signal serves as the reference.

 

If this signal is not available, the unit’s internal

 

reference is used.

 

0003

SD REF :

 

The SD REF input signal serves as the reference.

 

If this signal is not available, the unit’s internal

 

reference is used.

 

0004

E-AUTO :

 

When the editing mode is selected, the state is the

 

same as when set to “INPUT.”

 

When any mode other than the editing mode is

 

selected, the state is the same as when set to

 

“AUTO.”

 

For details, refer to “Reference signals” (page 16).

 

 

032*1

Select the reference to synchronize the image frames

REC REF

for recording.

0000

NORMAL :

 

 

The video signal which is input is automatically

 

identified and serves as the reference.

 

0001

SLTC :

 

The time code which is input to the HD SDI IN

 

connector isidentified and serves as the reference.

 

<Note>

 

 

When the SLTC is selected, the following settings are

 

necessary to validate the settings for this item.

 

z Menu No. 25 SYSTEM FREQ: 59/60

 

z Menu No. 020 SYS FORMAT: 720p

 

z INPUT SELECT button on the front panel: HDSDI

 

 

 

Formats for playback

Depending on how the menu item No.020 SYS FORMAT, No.022 PB FORMAT and No.023 FORMAL SEL settings are combined, the formats of the tapes played back by the unit differ as shown in the table below.

022.

020.

023.

Playback format

PB FORMAT

SYS FORMAT

FORMAT SEL

 

 

 

 

 

 

 

 

 

 

 

HD_LP

DVCPRO HD-LP (1080i)

 

 

 

 

 

 

HD_SP

DVCPRO HD (1080i)

 

 

 

 

 

1080i

50M

DVCPRO50 (422)

 

 

 

 

25M

DVCPRO (411)

 

 

 

 

 

 

 

 

DV

DV

 

 

 

 

MANUAL

 

DVCAM

DVCAM

 

 

 

 

HD_LP

DVCPRO HD-LP (720p)

 

 

 

 

 

 

 

 

HD_SP

DVCPRO HD (720p)

 

 

 

 

 

720P

50M

DVCPRO50 (422)

 

 

 

 

25M

DVCPRO (411)

 

 

 

 

 

 

 

 

DV

DV

 

 

 

 

 

 

DVCAM

DVCAM

 

 

 

 

 

If AUTO is selected as the

DVCPRO HD-LP

 

menu item No.022 PB

(1080i/720p),

 

FORMAT setting, the

DVCPRO HD (1080i/

 

format applying when the

720p), DVCPRO50

 

format is not yet detected

(422), DVCPRO (411),

 

(when the tape inserted)

DVCPROP (420p), DC

AUTO

follows the menu item

or DVCAM format is

 

No.023 FORMAL SEL

detected automatically.

 

setting.

 

 

 

However, if “DV” or

 

 

“DVCAM” is selected,

 

 

operation proceeds as if

 

 

“HD_LP” is selected.

 

 

 

 

 

<Notes>

zWhen the tape is ejected, the format follows the one selected by menu item No.020 SYS FORMAT setting.

zDVCPRO P playback is not possible.

*1 Displayed menus may vary depending on the settings in menu No. 25 SYSTEM FREQ. For details, refer to “Menus which are displayed” (page 32).

“_____” indicates the factory setting.

39