Panasonic AJ-HD1400E, J-HD1400P DIF, (continued)

Setup menus (continued)

DIF

No./Item		Description of setting
880*1	For setting the transfer speed of the IEEE1394 digital
DIF SPEED	interface output.
	0000	S100 :
	100 Mbps
	0001	S200 :
	200 Mbps
	0002	S400 :
	400 Mbps
	<Note>
	When S100 has been selected as this item’s setting,
	DVCPRO HD format signals cannot be input or
	output.
882*1	For setting the input channel.
DIF IN CH	0000	0
	:	:
	0063	63
	The input channel is fixed at the channel
	corresponding to the number specified.
	0064	AUTO :
	The input channel is not fixed at the channel
	corresponding to the number specified. The input
	channel is initialized to 63 when the power is
	turned on.
883*1	For setting the output channel.
DIF OUT CH	0000	0
	:	:
	0063	63
	The input channel is fixed at the channel
	corresponding to the number specified.
	0064	AUTO :
	The output channel is not fixed at the channel
	corresponding to the number specified. The output
	channel is initialized to 63 when the power is
	turned on.
886*1	Menu item for expansion purposes. Normally, use
DIF CONFIG	DFLT as the setting.
	0000	DFLT
	0001	1
	:	:
	0255	255
890*1	For setting the audio channels to which the signals
DIF AUD OUT	from the IEEE1394 digital interface are to be output in
	the DV format when a DVCPRO HD tape or 50M
	format tape is played back or when a DV tape in 4ch
	mode is played by the audio signals and menu No.
	891 DIF DV AUDIO is set to “LOCK48.”
	0000	CH1/2 :
	CH1 and CH2
	0001	CH3/4 :
	CH3 and CH4
891*1	For setting forcible audio mode conversion when a DV
DIF DV	tape is played back and the audio signals are output
	in the DV format.
AUDIO
	0000	THRU :
	Normal setting (the signals simply pass through).
	0001	LOCK :
	Forcible conversion to the LOCK mode (no
	frequency conversion)
	0002	LOCK48 :
	Forcible conversion to 48kHz/2CH/LOCK.

No./Item		Description of setting
892*1	For setting how to reply when signals requesting a
DIF SIG CMD	confirmation of the format is sent from an external
	device connected by the IEEE1394 digital interface.
	0000	50M :
	DVDPRO50 is forcibly returned.
	0001	25M :
	DVDPRO is forcibly returned.
	0002	DV :
	DV is forcibly returned.
	0003	AUTO :
	The reply is the same format as the signal format
	output from the IEEE1394 digital interface.
	<Note>
	When the unit is connected to a non-linear editing
	system using 50M, 25M, and DV signal format, the
	non-linear editing system may not operate properly. In
	this case, set the value to reply with the format signal
	supporting the connected signal format and start the
	system.
894*1	For selecting channels that are adjusted with the
HD > DIF	audio volume control on the front panel and displayed
	on the audio level meter.
OUT
	0000	HD :
	DVCPRO HD
	0001	50M :
	DVCPRO50
	0002	DV :
	DV
895*1	For setting the format of the signals to be output from
50M > DIF	the IEEE1394 digital interface when a 50M format
	tape is played back.
OUT
	0000	50M :
	DVCPRO50
	0001	DV :
	DV
	<Note>
	When DV is selected as this item’s setting, the closed
	caption signals and time code (VITC) signals in the
	vertical blanking period are transmitted, but none of
	the other signals in the vertical blanking period are
	transmitted.
896*1	For setting the format of the signals to be output from
25M > DIF	the IEEE1394 digital interface when a 25M format
	tape is played back.
OUT
	0000	25M :
	DVCPRO
	0001	DV :
	DV
899*1	For setting whether the superimposed display is to be
DIF SUPER	output from the IEEE1394 digital interface when the
	format is converted (from HD to 50M, from HD to DV,
	from 50M to DV or from 25M to DV).
	0000	OFF :
	The superimposed text is not displayed.
	0001	ON :
	The superimposed text is displayed.
	<Note>
	Only TCR is displayed.

*1 Displayed menus may vary depending on the settings in menu No. 25 SYSTEM FREQ. For details, refer to “Menus which are displayed” (page 32).

“_____” indicates the factory setting.

53