Panasonic AJ-HD1400E, J-HD1400P SYSTEM, (continued)

Setup menus (continued)

SYSTEM

No./Item		Description of setting
05	For setting whether to perform the various
ENCODER	adjustments for the video output signals using this
SEL	VTR or using an external encoder remote controller.
	0001	LOCAL :
	The various adjustments for the video output
	signals are performed using this VTR.
	0002	BOTH :
	The various adjustments for the video output
	signals are performed using both this VTR and an
	external encoder remote controller.
	<Notes>
	z For video adjustments, refer to “Video output signal
	adjustments” (page 35).
	z If the signals are adjusted with the external
	encoder remote controller, the adjusted values are
	reflected in the setup menu. However, the adjusted
	numerical values will not be stored unless about 1
	minute has elapsed after completion of the
	adjustment operation. If the unit is turned off after
	executing the adjustments with the external
	encoder remote controller, it is necessary to wait
	about 1 minute before turning off the power.
	z Settings in this menu are not effective for the
	IEEE1394 digital output.
06	For selecting what is to be controlled when the video
V LEVEL	output level is to be adjusted by an external encoder
CTRL	remote controller.
	0000	HD :
	The HD video output level can be adjusted.
	0001	SD :
	The SD video output level can be adjusted.
	0002	BOTH :
	Both the HD and SD video output levels can be
	adjusted.
	<Note>
	When “CMPST” is selected in menu No. 650 STYLE,
	the unit will be in the same state as when “BOTH” is
	selected, regardless of the settings in this item.
12	For adjusting the system phase of the HD SDI output
SYS H	signals. (in 13.5 ns increments).
(HD)	– :Phase advances.
	+ :Phase delays.
	0000	–1100
	:	:
	1100	0
	:	:
	2200	1100
	<Notes>
	z When menu item No. 25 SYSTEM FREQ is set to
	50i/25P, 25 (HD), 25(SD), 50 (HD) or 50 (SD), the
	setting range is from –1320 - 0 - 1320.
	z When menu item No. 25 SYSTEM FREQ is set to
	23/24, the setting range is from –1375 - 0 - 1375.
14	For adjusting the system phase of the analog
SYS SC	composite output and SD SDI output signals (total
(SD)	variable range of over ±180 degrees).
	– :Phase advances.
	+ :Phase delays.
	0000	–108
	:	:
	0108	0
	:	:
	0216	108

No./Item		Description of setting
15	For adjusting the system phase of the analog
VO SYS H	composite output signals (in 37 ns increments).
(SD)	– :Phase advances.
	+ :Phase delays.
	0000	–858
	:	:
	0858	0
	:	:
	1716	858
	<Note>
	The setting range is –864 to 0 to 864 when 50i/25P,
	25 (HD) or 25 (SD) is selected as the menu item
	No.25 SYSTEM FREQ setting.
16	For adjusting the system phase of the SD SDI output
SD SYS H	signals (in 37 ns increments).
(SD)	– :Phase advances.
	+ :Phase delays.
	0000	–858
	:	:
	0858	0
	:	:
	1716	858
	<Note>
	The setting range is –864 to 0 to 864 when 50i/25P,
	25 (HD) or 25 (SD) is selected as the menu item
	No.25 SYSTEM FREQ setting.
18	For adjusting the SCH (sub-carrier to horizontal)
SCH	phase of the analog composite output signals (4
COAR	positions in 90-degree increments).
(SD)	The SC phase changes, and the H phase remains
	unchanged.
	0000	0
	0001	90
	0002	180
	0003	270
19	For adjusting the SCH (sub-carrier to horizontal)
SCH FINE	phase of the analog composite output signals
(SD)	(variable range of over ±45 degrees).
	The SC phase changes, and the H phase remains
	unchanged.
	A range of ±180 degrees is covered by using this
	setting in combination with item No.18 SCH COAR
	(SD).
	0000	–32
	:	:
	0032	0
	:	:
	0064	32

20For adjusting the phase of the AUDIO output signals

AV	in relation to the video output signals (in 20.8 µs
PHASE	increments).
	– :Audio phase against image advance.
	+ :Audio phase against image delay.
	0000	–100
	:	:
	0100	0
	:	:
	0200	100

“_____” indicates the factory setting.

36