Motion Detector Motion DET, Motion detect menu | Panasonic WV-CW864

●Motion Detector (MOTION DET)

1.Display SET UP MENU on the monitor screen by referring to page 16.

2.Move the cursor to MOTION DET and select ON or OFF by using the joystick.

The factory default setting is OFF.

3.If ON is selected, press the CAM (SET) key. The MOTION DETECT menu appears.

You can mask the areas in this menu.

4.Move the cursor to MASK SET and press the CAM (SET) key.

48 mask areas appear on the monitor screen.

Refer to the Light Control Setting on page 37 for masking opera- tions.

5.After masking areas, press the MON (ESC) key. The MOTION DETECT menu appears on the monitor screen.

6.Move the cursor to ALARM and select ON or OFF by using the joystick.

The factory default setting is OFF.

ON: The alarm signal is supplied while the display mode is acti- vated.

OFF: The alarm signal is not supplied while the display mode is activated.

7.Move the cursor to DISPLAY MODE.

Press the CAM (SET) key to see the present setting. The areas that detect the motions blink.

8.Move the cursor to LEVEL by using the joystick.

Obtain the optimum detection level by moving the joystick to the right or left.

Note: Repeat the above procedures until you obtain the adjusted results.

9.Move the cursor to RECOVER TIME by using the joystick. The factory default setting is 1 MIN.

You can select the following recover times.

OFF1MIN2MIN 3MIN 5MIN

60MIN 30MIN20MIN10MIN

10.Move the cursor to RET and press the CAM (SET) key to return to

SET UP.

Camera setting menu

SET UP
CAMERA ID		OFF
ALC/MANUAL		ALC
SHUTTER		OFF
AGC		ON(MID)
SENS UP		X2 AUTO
SYNC		INT
WHITE BAL		ATW1
MOTION DET		ON
AF MODE		MANUAL	S
RET	SPECIAL2

Motion detect menu

MOTION DETECT

LEVEL					••••••••
DISPLAY MODE					-			+
DISPLAY MODE
		ALARM			OFF
MASK SET
RECOVER TIME					1MIN
RET

43

Image 42

Panasonic WV-CW864 operating instructions Motion Detector Motion DET, Motion detect menu

Contents

Operating Instructions Contents Important Safety Instructions English Features Preface Preset Data Uploading or Downloading PrecautionsCamera Cleaning Do not attempt to disassemble the cam- era If Over Heat appears on the monitor screen Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun Consumables Construction Setup Setup Menu SET Key CAM SET Key Down Switch Focus Switch Zoom SwitchUp Switch Right Switch Left Switch Close CAM Setup F4 key Key for 2 sec Key for 2 seco Auto Mode Auto Mode Setup Menu DescriptionPresetting Home Position Home Position Local/Remote LOCAL/REMOTE Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Special 1 Menu Camera Electronic Sensitivity Enhancement Sens UP Shutter Speed ShutterGain Control AGC Synchronization Sync RS485 communication Menu Display Setting ProceduresSetup Menu Display Submenu Display Position Setting Position SET PresettingPreset Menu Display To Set Panning/Tilting Positions ZOOM/FOCUS setting menu Pan OffsetTo Set the Lens Zoom and Focus Positions To Copy a Preset ID from Another Position Preset Identification Setting Preset IDTo Enter a New Preset ID To Change an Entered Preset ID To Return to the Preset Setting Menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID Manual setting menu To Return to the Preset Number Set Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Setup Menu Deleting Preset Positions Home Position SettingSelf Return Setting Self Return Auto Mode Selection Auto Mode Auto PAN setting menu When the panning, tilting, zooming or focusing in the SEQ Auto Pan Key Setting Digital Flip Setting Digital Flip Local/Remote Setting LOCAL/REMOTE Special 1 Menu Setting SpecialPrivacy Zone Privacy Zone Zone Scale setting menu Proportional Pan/Tilt PROPO. P/T When on Nesw is selectedArea Title Nesw setting menu Area Title Area Title Direction User setting menu Setting on UserDisplay Position setting menu Area Title Editing Patrol-learn and Patrol Play Patrol To Quit EditingArea Title menu Patrol Play with a Controller Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller not Having the Patrol Key Alarm Input/Output Alarm IN/OUT Alarm I/O submenuCNT-CLS 1, 2 Output Password Lock Password Lock Password Verification Cleaning Cleaning New Password Preset Alarm Preset ALM Electronic Zoom EL-ZOOMImage Hold Image Hold Camera setting menu Camera SettingTo Display the Camera Setting Menu Camera Identification Camera ID Backlight compensation menu Turns to white Blinking Shutter Speed Setting Shutter Gain Control AGCElectronic Sensitivity Enhancement Sens UP Line-lock Sync Mode LL Synchronization SyncSync menu Auto-Tracing White Balance Mode ATW1/ATW2 ATW fine adjustment menuWhite Balance White BAL Automatic White Balance Control Mode AWC AWC fine adjustment menu Motion Detector Motion DET Motion detect menu Auto Focus Setting AF Mode Special 2 Menu SPECIAL2 Black Burst Setting Burst BW To Restore the Camera Default Position RefreshCamera Resetting Camera Reset RS485 Setup Initial Camera Communication ParametersChanging the Camera Communication Parameters Unit Number Unit Number Alarm Data Alarm DataDelay Time Delay Time Sub Address SUB Address Mounting the Camera InstallationPrecautions Ceiling mount Mounting the Bracket PreparationsDisassembling the Camera Waterproof Material X4 Screws Upper Base Setting the Switches RS485 Parameter Setup For Panasonic’s Protocol Unit Number Switch position Unit RS485 Setting Mounting the camera AC Power Supply Connection How to Assemble the Cable with the Accessory ConnectorConnections Alarm in Connections Alarm OUT ConnectionsRS485 Connection System Connections Power consumption SpecificationsSignal-to-noise ratio Prevention of Blooming and Smear Accessories Optional AccessoriesWV-7176E Appendix Shortcuts N0202-1032 V8QA5996BN Imprimé au Japon Regional Offices