Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 3088 user manual Operation, Remote Console Manual Information, Specifications

Models: 3088

1 48

Download 48 pages 47.56 Kb

Page 3

6.0	Operation	33
6.1	Power-up	33
6.2	LED Status Monitors	33
	Power (Green)	33
	DSL (Green)	33
	Term (Green)	34
	TM/ER (Red)	34
6.3	Test Modes	34
	Loopbacks	34
	Patterns	35
7.0 Remote Console Manual Information		36
7.1 Establishing a Remote Console Session		36
	How to Connect	36
	How to Disconnect	38
	Differences in Local and Remote Control Session Behavior	39
8.0 Model 3088 Software Upgrade Feature		41
9.0	Reset Configuration to Factory Defaults	42
A	Specifications	43
A.1	Clocking Modes	43
A.2	DTE Rate	43
A.3	Serial Interface	43
A.4	Serial Connector	43
A.5	Diagnostics	43
A.6	Status LEDs	43
	Power (Green)	43
	DSL (Green)	43
	Term (Green)	44
	TM/ER (Red)	44
A.7	Configuration	44
A.8	Power	44
A.9	Compliance	44
A.10 Transmission Line		44
A.11 Line Coding		44
A.12 Line Rates (DSL line)		44
A.13 Line Interface		45
A.14 G.SHDSL Physical Connection		45
A.15 Environment		45
B	Factory Replacement Parts and Accessories	46
C	Model 1088/CA Interface Pin Assignments	47
D	Model 3088/D Interface Pin Assignments	48

3

Image 3

Patton electronic Operation, Remote Console Manual Information, Model 3088 Software Upgrade Feature, Specifications

Contents

An ISO-9001 Certiﬁed Company USER MANUALG.SHDSL Modem MODEL 3088 RocketLink-G NTUInstallation CONTENTSWarranty Information ConfigurationFactory Replacement Parts and Accessories 8.0 Model 3088 Software Upgrade FeatureReset Configuration to Factory Defaults Specifications1.2 FCC PART 68 ACTA STATEMENT 1.0 COMPLIANCE INFORMATION 1.1 RADIO AND TV INTERFERENCE1.4 CE NOTICE 1.3 INDUSTRY CANADA NOTICE2.0 WARRANTY INFORMATION 2.1 SERVICETel +1 301 Email support@patton.com 3.1 FEATURES 3.0 GENERAL INFORMATION3.2 DESCRIPTION Figure 1. Model 3088 3088/D version shown 4.0 CONFIGURATIONPossible DefaultParameter DescriptionPossible DefaultParameter DescriptionDescription 4.1 CONFIGURING THE DIP SWITCHESDefault ParameterSoftware Upgrades 4.2 SYSTEM RESET MODEPosition Conﬁguration Reset to Factory Defaults4.3 DIP SWITCH SETTINGS Factory DefaultS1-7 - S1-1 Data Rate SettingS1-8 TX Clock S1-8S1-4 S1-7S1-6 S1-5S2-6 S2-5 - S2-4 Clock ModeClock Mode LoopsS2-3 S2-1 Front Panel SwitchesFront Panel Switches S2-3 Annex A/BDSL Error Monitor Interval Time The length in seconds of an interval DSL Line Condition Good or Poor system set circuitid circuitid Sets the circuit ID Help CommandsSystem Conﬁguration Commands system set password password Sets the system passwordSystem Status Commands system show clockmode Shows the clock modedsl set annex ab Set the annex DSL Conﬁguration Commandsdsl set lineprobe enableddisabled Enable or disable line probe Startup DelayDSL Status Commands dsl show linkspeed Shows the actual DSL data rate minus DSL overhead dsl show linecond Shows the line condition good or poordsl show nmr Shows the noise margin ratio Example Command Line Interface Session Remote ConsoleThe dsl clear errcntrs command clears the error counters tx fifo empty tx fifo slip tx stuff rx fifo full rx fifo empty password dsl clear errcntrs dsl show errcntrs crc0 losw tx fifo fulldsl set pattern 511e dsl show testmode ber status in progress errors time dsl set pattern off dsl set loopback off logout password3088 CP 3096RC CO5.1 CONNECTING THE TWISTED PAIR INTERFACE 5.0 INSTALLATIONConnecting the Model 3088/CA V.35 to a “DTE” Device 5.2 CONNECTING THE MODEL 3088/CA SERIAL INTERFACEConnecting the Model 3088/CA V.35 to a “DCE” Device 5.3 CONNECTING THE MODEL 3088/D X.21 SERIAL INTERFACEConnecting the Model 3088/D X.21 to a “DCE” or “DTE” Device Opening the Case replacement should only be performed by quali 5.4 CONNECTING POWERThere are no user-serviceable parts in the power supply section of the Model 3088. Fuse6.2 LED STATUS MONITORS 6.1 POWER-UPPower Green 6.0 OPERATION6.3 TEST MODES Term Green3088/D with the X.21 interface TM/ER RedPatterns Figure 13. Local Analog Loopback diagramFigure 14. Remote Digital Loopback diagram 7.0 REMOTE CONSOLE MANUAL INFORMATION 7.1 ESTABLISHING A REMOTE CONSOLE SESSION How to Connectconsole connection system show status command shows that DSL link is not up How to Disconnectcommand logout is Console Remote console connection lost. The fol remote console Console Remote console connection established password Differences in Local and Remote Control Session Behaviorlogout Console Remote console connection lost Near End Figure 17. Remote control session with LAL diagram8.0 MODEL 3088 SOFTWARE UPGRADE FEATURE 9.0 RESET CONFIGURATION TO FACTORY DEFAULTS APPENDIX A A.4 SERIAL CONNECTORA.5 DIAGNOSTICS A.6 STATUS LEDS Power GreenA.10 TRANSMISSION LINE A.7 CONFIGURATIONA.8 POWER A.9 COMPLIANCERJ-45, 2-wire polarity insensitive pins 4 and A.13 LINE INTERFACEA.14 G.SHDSL PHYSICAL CONNECTION A.15 ENVIRONMENTDescription APPENDIX BModel # FACTORY REPLACEMENT PARTS AND ACCESSORIESSignal APPENDIX CPin # Signal APPENDIX D