Model 3088 Software Upgrade Feature | Patton electronic instruction

8.0 MODEL 3088 SOFTWARE UPGRADE FEATURE

The 3088 is software upgradeable through the console port. Software images will be available in Intel Hex ﬁle format.

The software upgrade feature is available either by powering up the 3088 will all dipswitches set to the “Off” position, or by entering the “system upgrade” command on the command line interface. The software upgrade takes approximately 5 minutes to complete. The 3088 will print ‘.’ to the screen while the software upgrade is in process. When the soft- ware upgrade completes, it will print a message stating that it is complete and the number of errors, if any, that occurred.

Errors may occur during the software upgrade if the image is corrupt or if there is a disruption in the console port connection. The 3088 will print a message to the console port if it encounters any errors. In the event of an error, the portions of the old image may have been overwritten, and the unit may not be able to boot into operational mode. However, the unit may still boot into the software upgrade, so a new software image can still be loaded to bring the unit back to an operational state.

Here is the software upgrade procedure:

1.Obtain a software image Hex ﬁle.

2.Turn off the 3088.

3.Switch all DIP switches to the “Off” position.

4.Turn on the 3088.

5.Transfer the software image hex ﬁle through the console (8 bits/no parity/1 stop bit/XON-XOFF ﬂow control).

6.When the transfer completes, turn the 3088 off.

7.Set the DIP switches for the proper conﬁguration.

8.Turn on the 3088. It is now running the upgraded software.

41

Image 41

Patton electronic user manual Model 3088 Software Upgrade Feature

Contents

User Manual Contents Remote Console Manual Information Operation FCC Part 68 Acta Statement Compliance Information Radio and TV Interference CE Notice Industry Canada Notice Tel +1 301 Email support@patton.com Warranty InformationService Description FeaturesGeneral Information Model 3088 3088/D version shown Configuration Parameter Description Possible Default Values OFF, LAL Configuring the DIP Switches Parameter Description Possible Default Software Upgrades System Reset Mode Position Function Factory Default Conﬁguration Reset to Factory DefaultsDIP Switch Settings S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps S1-8 TX Clock Setting DescriptionS1-7 S1-1 Data Rate 1920 S2-5 S2-4 Clock Mode S2-6 SettingS2-5 S2-4 Clock Mode Description Loops S2-3 Annex A/B S2-1 Front Panel SwitchesS2-3 Annex S2-2 Line ProbePage CRC DSL Line Condition Good or Poor System Conﬁguration Commands Help Commands System Status Commands System show clockmode Shows the clock mode Startup Delay Interval Interval totint DSL Conﬁguration Commands DSL Status Commands Page Remote Console Example Command Line Interface Session Rocketlink Plug ‘N’ Play 3096RC Connecting the Twisted Pair Interface Installation Connecting the Model 3088/CA V.35 to a DTE Device Connecting the Model 3088/CA Serial Interface Connecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 Serial Interface Opening the Case Connecting the Model 3088/D to X.21 DTE or DCE Connecting Power Power Green POWER-UPOperation LED Status Monitors 3088/D with the X.21 interface Term GreenTM/ER Red Test Modes Patterns Local Analog Loopback diagram Establishing a Remote Console Session How to ConnectRemote Console Manual Information Page How to Disconnect System show status command shows that DSL link is not up Differences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Diagnostics Serial ConnectorAppendix a Clocking Modes Compliance PowerTransmission Line Line Coding Environment Line Interface14 G.SHDSL Physical Connection Model # Description Appendix B Appendix C Pin # Signal Appendix D Pin Signal