Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic user manual Configuration, Model 3088 3088/D version shown

Models: 3088

1 48

Download 48 pages 47.56 Kb

Page 8

4.0 CONFIGURATION

4.0 CONFIGURATION

The Model 3088 (see ﬁgure 1) has two conﬁguration modes, DIP switch and software.

Figure 1. Model 3088 (3088/D version shown)

DIP switch conﬁguration mode is entered by starting the unit with the DIP switches in any position other than all OFF or all ON. In DIP switch conﬁgu- ration mode, the DIP switch settings are read at system startup and used to conﬁgure the unit. Once the unit has started in DIP switch mode it will remain in DIP switch mode, and its settings cannot be changed. Console commands used to conﬁgure the unit will report that the unit is in DIP switch conﬁguration and will not change the conﬁguration. Likewise, EOC variables cannot be used to conﬁgure the device. Also note that changing the DIP switch settings while the unit is running will have no effect on the conﬁgura- tion as the DIP switches are only read on startup.

Software conﬁguration mode is entered by starting the unit with the DIP switches set to all ON. The system then reads any conﬁguration that might have been saved to FLASH. If no conﬁguration has been saved, then the factory defaults are loaded. The unit may be further conﬁgured by console commands or by EOC.

8

Image 8

Patton electronic user manual Configuration, Model 3088 3088/D version shown

Contents

USER MANUAL G.SHDSL ModemMODEL 3088 RocketLink-G NTU An ISO-9001 Certiﬁed CompanyCONTENTS Warranty InformationConfiguration Installation8.0 Model 3088 Software Upgrade Feature Reset Configuration to Factory DefaultsSpecifications Factory Replacement Parts and Accessories1.0 COMPLIANCE INFORMATION 1.1 RADIO AND TV INTERFERENCE 1.2 FCC PART 68 ACTA STATEMENT1.3 INDUSTRY CANADA NOTICE 1.4 CE NOTICETel +1 301 Email support@patton.com 2.0 WARRANTY INFORMATION2.1 SERVICE 3.2 DESCRIPTION 3.1 FEATURES3.0 GENERAL INFORMATION 4.0 CONFIGURATION Figure 1. Model 3088 3088/D version shownDefault ParameterDescription PossibleDefault ParameterDescription Possible4.1 CONFIGURING THE DIP SWITCHES DefaultParameter Description4.2 SYSTEM RESET MODE Software UpgradesConﬁguration Reset to Factory Defaults 4.3 DIP SWITCH SETTINGSFactory Default PositionSetting S1-8 TX ClockS1-8 S1-7 - S1-1 Data RateS1-7 S1-6S1-5 S1-4S2-5 - S2-4 Clock Mode Clock ModeLoops S2-6S2-1 Front Panel Switches Front Panel SwitchesS2-3 Annex A/B S2-3DSL Error Monitor Interval Time The length in seconds of an interval DSL Line Condition Good or Poor Help Commands System Conﬁguration Commandssystem set password password Sets the system password system set circuitid circuitid Sets the circuit IDsystem show clockmode Shows the clock mode System Status CommandsDSL Conﬁguration Commands dsl set lineprobe enableddisabled Enable or disable line probeStartup Delay dsl set annex ab Set the annexDSL Status Commands dsl show nmr Shows the noise margin ratio dsl show linkspeed Shows the actual DSL data rate minus DSL overheaddsl show linecond Shows the line condition good or poor The dsl clear errcntrs command clears the error counters Example Command Line Interface SessionRemote Console password dsl clear errcntrs dsl show errcntrs crc0 losw tx fifo full dsl set pattern 511e dsl show testmode ber status in progress errorstime dsl set pattern off dsl set loopback off logout password tx fifo empty tx fifo slip tx stuff rx fifo full rx fifo empty3096RC CO 3088 CP5.0 INSTALLATION 5.1 CONNECTING THE TWISTED PAIR INTERFACE5.2 CONNECTING THE MODEL 3088/CA SERIAL INTERFACE Connecting the Model 3088/CA V.35 to a “DTE” DeviceConnecting the Model 3088/D X.21 to a “DCE” or “DTE” Device Connecting the Model 3088/CA V.35 to a “DCE” Device5.3 CONNECTING THE MODEL 3088/D X.21 SERIAL INTERFACE Opening the Case 5.4 CONNECTING POWER There are no user-serviceable parts in thepower supply section of the Model 3088. Fuse replacement should only be performed by quali6.1 POWER-UP Power Green6.0 OPERATION 6.2 LED STATUS MONITORSTerm Green 3088/D with the X.21 interfaceTM/ER Red 6.3 TEST MODESFigure 14. Remote Digital Loopback diagram PatternsFigure 13. Local Analog Loopback diagram 7.1 ESTABLISHING A REMOTE CONSOLE SESSION How to Connect 7.0 REMOTE CONSOLE MANUAL INFORMATIONconsole connection command logout is Console Remote console connection lost. The fol system show status command shows that DSL link is not upHow to Disconnect logout Console Remote console connection lost remote console Console Remote console connection established passwordDifferences in Local and Remote Control Session Behavior Figure 17. Remote control session with LAL diagram Near End8.0 MODEL 3088 SOFTWARE UPGRADE FEATURE 9.0 RESET CONFIGURATION TO FACTORY DEFAULTS A.4 SERIAL CONNECTOR A.5 DIAGNOSTICSA.6 STATUS LEDS Power Green APPENDIX AA.7 CONFIGURATION A.8 POWERA.9 COMPLIANCE A.10 TRANSMISSION LINEA.13 LINE INTERFACE A.14 G.SHDSL PHYSICAL CONNECTIONA.15 ENVIRONMENT RJ-45, 2-wire polarity insensitive pins 4 andAPPENDIX B Model #FACTORY REPLACEMENT PARTS AND ACCESSORIES DescriptionPin # SignalAPPENDIX C APPENDIX D Signal