Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 3088 user manual Reset Configuration To Factory Defaults

Models: 3088

1 48

Page 42

9.0 RESET CONFIGURATION TO FACTORY DEFAULTS

The conﬁguration can be reset to factory defaults from the software reset mode. This allows a user to recover from a forgotten password. To reset to the conﬁguration, follow these steps:

1.Power down the unit.

2.Set all DIP switches to the OFF position.

3.Connect a PC to the Console port.

4.Open a VT100 terminal emulator (such as HyperTerminal). Conﬁg- ure the emulator for 19,200 kbps/1 stop bit/no parity/X-ON X-OFF ﬂow control.

5.Power up the unit. The terminal should display the following mes- sage: “Reset Mode”.

6.Type the ‘*’ key. You will see a ‘: ‘ prompt.

7.Type the command ‘reset’.

8.When the command completes, the unit has been reset to factory conﬁguration.

9.Set the DIP switches to the desired conﬁguration. Power cycle the unit to begin using the new software.

Page 42

Image 42

Patton electronic 3088 user manual Reset Configuration To Factory Defaults

Contents

MODEL 3088 RocketLink-G NTU USER MANUALG.SHDSL Modem An ISO-9001 Certiﬁed CompanyConfiguration CONTENTSWarranty Information InstallationSpecifications 8.0 Model 3088 Software Upgrade FeatureReset Configuration to Factory Defaults Factory Replacement Parts and Accessories1.0 COMPLIANCE INFORMATION 1.1 RADIO AND TV INTERFERENCE 1.2 FCC PART 68 ACTA STATEMENT1.3 INDUSTRY CANADA NOTICE 1.4 CE NOTICE2.0 WARRANTY INFORMATION 2.1 SERVICETel +1 301 Email support@patton.com 3.1 FEATURES 3.0 GENERAL INFORMATION3.2 DESCRIPTION 4.0 CONFIGURATION Figure 1. Model 3088 3088/D version shownDescription DefaultParameter PossibleDescription DefaultParameter PossibleParameter 4.1 CONFIGURING THE DIP SWITCHESDefault Description4.2 SYSTEM RESET MODE Software UpgradesFactory Default Conﬁguration Reset to Factory Defaults4.3 DIP SWITCH SETTINGS PositionS1-8 SettingS1-8 TX Clock S1-7 - S1-1 Data RateS1-5 S1-7S1-6 S1-4Loops S2-5 - S2-4 Clock ModeClock Mode S2-6S2-3 Annex A/B S2-1 Front Panel SwitchesFront Panel Switches S2-3DSL Error Monitor Interval Time The length in seconds of an interval DSL Line Condition Good or Poor system set password password Sets the system password Help CommandsSystem Conﬁguration Commands system set circuitid circuitid Sets the circuit IDsystem show clockmode Shows the clock mode System Status CommandsStartup Delay DSL Conﬁguration Commandsdsl set lineprobe enableddisabled Enable or disable line probe dsl set annex ab Set the annexDSL Status Commands dsl show linkspeed Shows the actual DSL data rate minus DSL overhead dsl show linecond Shows the line condition good or poordsl show nmr Shows the noise margin ratio Example Command Line Interface Session Remote ConsoleThe dsl clear errcntrs command clears the error counters time dsl set pattern off dsl set loopback off logout password password dsl clear errcntrs dsl show errcntrs crc0 losw tx fifo fulldsl set pattern 511e dsl show testmode ber status in progress errors tx fifo empty tx fifo slip tx stuff rx fifo full rx fifo empty3096RC CO 3088 CP5.0 INSTALLATION 5.1 CONNECTING THE TWISTED PAIR INTERFACE5.2 CONNECTING THE MODEL 3088/CA SERIAL INTERFACE Connecting the Model 3088/CA V.35 to a “DTE” DeviceConnecting the Model 3088/CA V.35 to a “DCE” Device 5.3 CONNECTING THE MODEL 3088/D X.21 SERIAL INTERFACEConnecting the Model 3088/D X.21 to a “DCE” or “DTE” Device Opening the Case power supply section of the Model 3088. Fuse 5.4 CONNECTING POWERThere are no user-serviceable parts in the replacement should only be performed by quali6.0 OPERATION 6.1 POWER-UPPower Green 6.2 LED STATUS MONITORSTM/ER Red Term Green3088/D with the X.21 interface 6.3 TEST MODESPatterns Figure 13. Local Analog Loopback diagramFigure 14. Remote Digital Loopback diagram 7.1 ESTABLISHING A REMOTE CONSOLE SESSION How to Connect 7.0 REMOTE CONSOLE MANUAL INFORMATIONconsole connection system show status command shows that DSL link is not up How to Disconnectcommand logout is Console Remote console connection lost. The fol remote console Console Remote console connection established password Differences in Local and Remote Control Session Behaviorlogout Console Remote console connection lost Figure 17. Remote control session with LAL diagram Near End8.0 MODEL 3088 SOFTWARE UPGRADE FEATURE 9.0 RESET CONFIGURATION TO FACTORY DEFAULTS A.6 STATUS LEDS Power Green A.4 SERIAL CONNECTORA.5 DIAGNOSTICS APPENDIX AA.9 COMPLIANCE A.7 CONFIGURATIONA.8 POWER A.10 TRANSMISSION LINEA.15 ENVIRONMENT A.13 LINE INTERFACEA.14 G.SHDSL PHYSICAL CONNECTION RJ-45, 2-wire polarity insensitive pins 4 andFACTORY REPLACEMENT PARTS AND ACCESSORIES APPENDIX BModel # DescriptionSignal APPENDIX CPin # APPENDIX D Signal