Manuals / Brands / Communications / Telephone / Phonetics / Communications / Telephone

Phonetics 1108 8.2 Sensaphone 1108 BusinessSitter Edition

1 134

Download 134 pages, 1.92 Mb

8.2 Sensaphone 1108 BusinessSitter Edition

The Sensaphone 1108 BusinessSitter allows you to monitor and

check on the status of your facility from any cellular or ordinary

telephone. The Sensaphone 1108 BusinessSitter turns a device on

when an alarm occurs. You can also inquire about the status of the

device during a voice status report.

This Sensaphone edition contains a relay contact on the rear of

the unit (See Figure 3). The relay contact supports a normally

open relay.

When the Sensaphone detects an alarm condition, it closes this

relay, which then activates the device attached to the relay. The

relay remains closed throughout the alarm process, even while the

Sensaphone is making its alarm-response telephone calls out to

you. Reset of the alarm relay may occur either locally or remotely

via the telephone. This is discussed further in following sections.

The Sensaphone relay is a low voltage relay. Only voltages less

than 30 volts AC 2AMPS, or 30 volts DC 2AMPS may be

switched. For higher voltages, an additional high-voltage relay

would be required.

Always enlist the services of a licensed electrician

when working with high voltages.Improper wiring

can cause harm to you or your property.

NOTE: For safety reasons it is highly recommended that the unit

only be used to switch low voltage signals (30 volts or less). If

you intend to control higher voltages you must install the unit in

an NEC approved electrical panel or enclosure and have wiring

performed by a qualified electrician.

8.2.1 Switching the Output using the Keypad

To switch the output ON from the keypad:

1. Press STATUS.

2. Press 6.

6

CALIBRATE

STATUS

CONFIGURE

Chapter 8:Special Editions

105

Contents

Main Page IMPORTANT SAFETY INSTRUCTIONS CAUTION UL 60950 FCC Requirements Page Canadian Department of Communications Statement Page 1 YEAR LIMITED WARRANTY ix SensaphoneModel 1108 Users Manual x xi xii TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . iii Chapter 1: Introduction . . . . . . . . . . . . . . . . . 19 Chapter 2: Installation . . . . . . . . . . . . . . . . . . 21 Chapter 3: Quick Start. . . . . . . . . . . . . . . . . . 31 Chapter 4: Communications Programming. 39 Chapter 5: Alarm Programming . . . . . . . . . . 67 Chapter 6: Acknowledgment, Status Report & Remote Access . . . . . . . . . . . . 85 Chapter 7: Operation . . . . . . . . . . . . . . . . . . . 93 Chapter 8: Model 1108 Special Editions . . . 99 Page Page Chapter 1: Introduction Technical Support Chapter 2: Installation 2.1 Operating Environment 2.2 Mounting 2.3 Power Surge Protection 2.4 Power Supply and Battery Backup --- --- +++ +++ 2.6 Run Mode and Standby Mode 2.7 Telephone Line 2.8 The Microphone 2.9 Alert Inputs 2.10 Installing the Sensor 2.11 Multiple Sensors 2.12 Outdoor Wiring 2.13 Disconnecting the Model 1108 for Storage or Seasonal Use. Page Chapter 3: Quick Start 3.1 The Local Keypad 3.2 Preparation for Programming 3.3 Quick-Start Programming Steps Step 1: Set Configuration of Inputs Step 2: Set the ID Number Step 3: Set Dial-Out Telephone Numbers Step 4: Set Temperature Limits Page Page ActionResponse 3.4 Summary of the Alarm Dial-Out Process Programmable Feature Page Chapter 4: Communications Programming 4.1 The Unit ID Number 4.1.1 Programming the ID Number 4.1.2 Interrogating the ID Number 4.2 Dial-out Telephone Numbers 4.2.1 Programming Dial-out Telephone Numbers 4.2.2 Interrogating a Dial-out Telephone Number 4.2.3 Erasing a Telephone Number 4.3 Tone or Pulse Dialing 4.4 Special Dialing 4.4.1 Special Dialing Keys 4.4.2 Incorporating a Pause 4.4.3 Incorporating a Pound (#) or Asterisk (*) 4.4.4 Special Dialing to a Beeper or Pager Page Page 4.5 Rings Until Answer 4.5.1 Programming Rings Until Answer 4.5.2 Interrogating Rings Until Answer 4.5.3 Double Ring Compatibility 4.5.4 Interrogating Double Ring Compatibility 4.6 TAD (Telephone Answering Device) 4.6.1 TAD Enable/Disable 4.6.2 Using the TAD Feature 4.6.3 No TAD In Use 4.7 Listen-in Time 4.7.1 Programming the Listen-in Time 4.7.2 Interrogating the Listen-in Time 4.8 Call Delay 4.8.1 Programming the Call Delay 4.8.2 Interrogating Call Delay 4.9 Local Voice Mute 4.9.1 Enable/Disable Local Voice Mute 4.10 Voice Repetitions 4.10.1 Programming Voice Repetitions 4.10.2 Interrogating Voice Repetitions 4.11 Intercall Time 4.11.1 Programming Intercall Time 4.11.2 Interrogating Intercall Time 4.12 Maximum Number of Calls (Max Calls) 4.12.1 Programming Max Calls 4.12.2 Interrogating Max Calls 4.13 The Clock 4.13.1 Setting the Clock 4.13.2 Interrogating for the Current Time 4.14 The Security Code 4.14.1 Locking the Keypad 4.14.2 Unlocking the Keypad Page Page Chapter 5: Alarm Programming 5.1 Input Configuration 5.1.1 Programming Input Configuration 5.1.2 Verifying Input Configuration 5.2 Enable/Disable Inputs 5.2.1 Changing Enabled/Disabled Input Status 5.2.2 Verifying Enabled/Disabled Input Status 5.3 Input Recognition Time 5.3.1 Programming Input Recognition Time 5.3.2 Interrogating Input Recognition Time 5.4 Establishing High and Low Temperature Limits 5.4.1 Programming Temperature Limits for a Selected Input Page 5.4.2 Disabling Alarm Response to High or Low Temperature 5.4.3 Interrogating High and Low Temperature Limits 5.5 Temperature Scale 5.6 Temperature Calibration 5.6.1 Programming Temperature Calibration Page 5.6.2 Interrogating Temperature Calibration 5.7 Obtaining Current Temperature 5.8 AC Power Monitoring Enable/Disable 5.8.1 Enabling/Disabling the AC Power Alarm 5.9 AC Power Failure Recognition Time 5.9.1 Programming Power Failure Recognition Time 5.9.2 Interrogating Power Failure Recognition Time 5.10 Sound Alarm Monitoring 5.10.1 Programming Sound Alarm Sensitivity 5.10.2 Interrogating Sound Sensitivity 5.10.3 Programming High Sound Alarm Recognition Time 5.11 High Sound Alarm Enable/Disable 5.11.1 Changing Enabled/Disabled High Sound Alarm 5.12 Exit Delay Chapter 6: Acknowledgment, Status Report & Remote Access 6.1 Alarm Acknowledgment 6.1.1 Local Acknowledgment 6.1.2 Touch-ToneAcknowledgment 6.1.3 Callback Acknowledgment 6.2 Status Report 6.2.1 Example: Status Report, No Alarms 6.2.2 Example: Status Report, Existing Alarms 6.2.3 Example: Status Report, Disabled Inputs 6.2.4 Battery Condition 6.2.5 Remote Access by Touch-ToneTelephone Page Chapter 7: Operation 7.1 Alarm Detection, Dial-out and Acknowledgment Page Page Page Page 7.2 Example: A Dial-out Telephone Call Chapter 8: Model 1108 Special Editions 8.1 Sensaphone 1108 CottageSitter Edition 8.1.1 Switching the Output using the Keypad 8.1.2 Switching the Output over the Telephone 8.1.3 Heating up your Cottage or Cabin Remotely 8.1.4 The Dual Thermostat Concept Page 8.1.5 Controlling Lights or other devices 8.1.6 Relay Output Specifications 8.2 Sensaphone 1108 BusinessSitter Edition 8.2.1 Switching the Output using the Keypad 8.2.2 Switching the Output over the Telephone 8.2.3 Relay Output Specifications 8.3 Sensaphone 1108 RemoteControl Edition 8.3.1 Switching the Output using the Keypad 8.3.2 Switching the Output over the Telephone 8.3.3 Controlling Lights or other devices 8.3.4 Relay Output Specifications 8.4 Model 1118 Line Seizure Edition 8.4.1 How Line Seizure Works 8.4.2 Hookup to the Phone Line Appendix A: Weekly Testing Procedure Page Appendix B: Troubleshooting Error Messages Communications / Dial-out: Communications / Dial-out (continued): Page Temperature Monitoring: Sound Level Monitoring: Other Monitoring: Other Monitoring (continued): Page Page Parameter Description Key Sequence* Range Default Appendix C: 1108 QUICK REFERENCE * press [ENTER] after all Key Sequences starting with [SET] SPECIAL KEY FUNCTIONS: Parameter Description Key Sequence Response Default Activate Listen-in: [#] + [1] Activate Status Report: [#] + [2] Disconnect: [#] + [#] Appendix D: Accessories Page Appendix E: Specifications Alert Inputs Microphone Phone Interface LED Indicator Power Supply Environmental Physical Certifications Appendix F: Returning the Unit for Repair SERVICE DEPARTMENT Phonetics, Inc. 901 Tryens Road Aston, PA 19014