Pioneer AVIC-Z1 operation manual UPDATING Updating

Message	When	What to do
UPDATING (Updating)	The selected channel is not included	Select another channel.
	in your subscription.
	Radio is being updated with the lat-	Wait until the encryption code is fully
	est encryption code.	updated.
Route calculation was not possible.	Route calculation has failed because	• Change the destination.
	of malfunction of map data, software,	• Consult the Pioneer Local dealer if
	hardware.	this message persists.
Route calculation was not possible	If the destination is too far.	• Set a destination closer to the start-
because the destination is too far.		ing point.
		• Set one or more waypoints.
Route calculation was not possible	The destination or waypoint(s) are	Set a destination [and waypoint(s)]
because the destination is too near.	too close.	farther from the starting point.

NAVI/AV

Route calculation was not possible due to traffic regulations.

•The destination or waypoint(s) are in a Control Traffic Zone (CTR) and the route calculation is hampered.

•Your vehicle is currently in a Con- trol Traffic Zone (CTR) and the route calculation is hampered.

•Set a destination and waypoint(s) outside the CTR if you know where the restricted area is.

•Try the destination or waypoint(s) away from the currently set points to some extent.

•Drive your vehicle to an unre- stricted area and reset the destina- tion and waypoint(s).

Route calculation was not possible	The destination, waypoint(s), or start-	• Set a destination and waypoint(s)
because no guidance can be pro-	ing point are in an area where no	on roads.
vided around the destination or the	road exists (e.g. a mountain) and the	• Reset the destination after you
starting point.	route calculation is impossible.	drive the vehicle to any road.
Route to destination cannot be cal-	The destination or waypoint(s) are in	Change the destination.
culated.	an isolated island, etc. without a ferry
	and the route calculation is impossi-
	ble. If there is no road connect to
	your starting point or destination,
	this message will appear.

Appendix

•Ferry could not be avoided.

•Toll road could not be avoided.

•Freeways could not be avoided.

•Toll roads, ferries and freeways could not be avoided.

•Toll roads and ferries could not be avoided.

•Toll roads and freeways could not be avoided.

•Ferries and freeways could not be avoided.

In case a ferry route, toll roads or freeways are included in the route to the destination or waypoints even though a route is set to avoid them. You can recognize these condition by icon.

➲“Checking and fixing the route” ➞ Page 30

If the current route is not desired, set destination or waypoints that do not pass through a ferry route, toll roads or freeways.

The address does not exist.	If the house number entered does	Re-enter the existing house number.
Do you want to continue?	not exist in the database for the spec-	Or, proceed to the next step without
	ified street.	entering the house number and set
		the main point of that street as your
		destination.
This area does not contain any POI’s	Facilities of the selected category do	Use another search method or move
of the selected type.	not exist in the surrounding areas.	to another location and perform the
		[Vicinity Search] again.
Failed to make the route profile.	In rarely case the route calculation	• Retry.
	error may occur.	• Consult the Pioneer Local dealer if
		this message persists.
There is no Traffic List.	There is no available traffic informa-	Move to the location where you can
	tion now.	receive the XM NavTraffic informa-
		tion, and then try the operation
		again.
There is no /Pictures/ folder.	Cannot load the image because the	Use the appropriate data after read-
Please create /Pictures/ folder and	Pictures folder is not found in the	ing “Limitations for import the pic-
store JPEG files in that Folder.	inserted disc.	ture” on page 97.

189