Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic 59060-02 B manual C 8700.0013 Connection failure, fabric limited to two switches

Models: 59060-02 B

1 62

Download 62 pages 21.93 Kb

Page 53

(C) (8700.0013) (Connection failure, fabric limited to two switches)

A

3 – Event Messages Critical Events

(C)(8700.000F) (EPort) (Port: port_number) (Broadcast frame received & broadcast disabled, discarding broadcast frames.)

Meaning:	Broadcast is disabled and the switch has received a broadcast
	frame. Enable broadcast to receive broadcast frames.

(C)(8700.0010) (EPort) (Port: port_number) (Inter-Switch Link (ISL) unstable. ISL init will be held back until ISL up time is 5 seconds)

Meaning:	The ISL is unstable indicating that the media module or the cable is
	bad.

(C)(8700.0011) (Eport) (Port: port_number) (Connection failure, remote switch not compatible)

Meaning:	The remote switch is not compatible with the local switch. The
	E_Port cannot exchange switch capabilities with the remote switch.

(C)(8700.0012) (Eport) (Port: port_number) (Connection failure, fabric limited to two switches)

Meaning:	The switch cannot be connected to the fabric due to a license
	restriction.
(C) (8700.0013) (Connection failure, fabric limited to two switches)
Meaning:	The switch cannot be connected to the fabric due to license
	restriction.
(C) (8F00.000C) Fabric Status status
Meaning:	The severity of the fabric status has changed. The description field
	will show the reason for fabric status.
(C) (8F00.000D) Switch Status status
Meaning:	The severity of the switch status has changed. The description field
	will show the reason for the switch status.
(C) (8F00:000E) Link Status status
Meaning:	The severity of the link status has changed. The description field
	will show the reason for link status.

59060-02 B

3-41

Image 53

Q-Logic 59060-02 B manual C 8700.0013 Connection failure, fabric limited to two switches

Contents

S i m p l i f y Firmware VersionQLogic Fibre Channel Switch Event Message Guide Revision B Changes Document Revision HistoryDocument Sections Affected 1.3.3Introduction SectionSection 2 Events and Event Logging Event Messages59060-02 B QLogic Fibre Channel Switch Event Message GuidePage Intended Audience IntroductionRelated Materials SectionTraining Technical SupportAvailability Support Headquarters Contact InformationNorth American Region Europe, Middle East, and Africa Region59060-02 B 1 - Introduction Technical SupportEvents and Event Logging Displaying Events using the Event BrowserUnderstanding Severity Levels SectionDisplaying the Events Using the Command Line Interface Archiving and Downloading the Event Log Configuring the Event LogConfiguring Port Alarm Thresholds Event Messages Alarm Events„ Alarm Events „ Critical Events „ Warning Events SectionA1003.000D Fabric already locked by domain domainID A1003.000C Fabric Busy, failing lock request from domain domainIDA1003.000E Couldnt acquire lock from domain domainID A1003.0010 Segmenting, zoneset zonesetname not definedA1003.0013 Segmenting, zone zonename merge conflict A1003.0021 Failing remote zoning configuration, Zoneset is empty A1003.0029 No response received from switch with domain ID domainID A1003.0025 Error reading security setA1003.002A No response received from switch with domain ID domainID A1003.002B No response received from switch with domain ID domainIDA1003.0030 Zone Merge rejected by remote switch A1003.002F SW2 Zoning Not Supported by other switch, Isolating linkA1003.0031 Error reading zoneset from activate direct A1003.0033 No memory for command completionReconcile interoperability modes on the local and remote switches Remove zone sets from the local switch zoning database to allowRemove members from the zone on the local switch or the remote Remove zone members from the local switch or the remote switchA1003.003C Incompatible Zoning mode, Isolating link A remote switch sent a merge request that was not understoodA1003.0040 Zone Member type membertype unsupported zone membership must be defined by domainID and port numberA1003.0050 ISL group does not contain entry for this switch A1003.004D Port group does not contain entry for this switchA1003.004F No Zone Merge Response A1003.0048 Active Zone Set set if not already longer activeA1003.0052 ISL group does not contain entry for switch domainID A1003.0051 Domain ID for local switch does not match fabric bindingA1003.0054 Failure at remote switch A1003.0055 Problem on zoning save of following switches domainIDlistA1003.0064 UFC failure received from domain domainID A1004.0010 Eport Isolating due to Remote switch using same domain ID A1004.000B Eport Isolating due to Switch Administratively OfflineAn EPort isolated because each fabric has a switch with the same An EPort isolated because the remote switch has the sameA1004.0012 Eport Isolating due to ISL Security A1004.0011 Eport Isolating due to Remote switch isolatedA1004.0014 Eport Isolating due to TOV mismatch indicated on ELP A1004.0015 Eport Isolating due to Invalid AttachAn EPort isolated because the values for RATOV or EDTOV An attempt was made by a remote switch to connect through a portremote switch so that they are the same. Otherwise, contact your The switch with the specified worldwide name is not allowed to joinlicensing on the remote switch. Otherwise, contact your authorized A1004.0040 binding indicates this domain is reserved for deviceWWNbinding indicates it should use domainID A1004.0041A1004.0052 Eport Isolating due to Switch Binding failure A1004.0051 Blade IO bladenumber isolated due to startup problemlimited to 64. If this number is exceeded, the switch cannot enforce A1004.0048 Eport Isolating due to Port Binding failureA1005.0013 AdminState A1005.003B Warning - Debug logging filter level is set A1007.0001 NS Unspecified zoning enforcement error A1006.0005 Zoning enforcement error in NameserverA1007.0005 Security Authentication request was rejected by port A1007.0002 Security WWN deviceWWN not authorized to joinA1007.0008 Security ESA Response failure, failing security checks A1007.000C Security policy restrict mode, security db differs A1007.001C Security Bad Authentication Flags A1007.0025 Security feature not supported A1007.0029 Security protocol not using chap, unable to authenticate A1007.0030 Security protocol not using chap, unable to authenticate A1007.0038 Device devicewwn failed switch binding A1007.0034 Device devicewwn failed switch bindingAn attempt to change the fabric binding setting was rejected due to A1007.0033 Device deviceWWN failed port bindingA2000.0001 A3001.0001 Temp overwarm, sensorname sensor reads value C - ALARM SET A3014.0003 Blade bladeID set Down due to blade type mismatch switch. Contact technical support if a non-disruptive code load and A6001.0003 cmon switch failed NDCLAA6001.0001 cmon insufficient memory A6001.0002 cmon blade failed NDCLACritical Events C 8400.0005 Switch The switch is now performing a hotreset C 8400.0015 Switch The switch will be reset in several seconds C 8400.0045 Switch Upgrading License for 4G capability C 8400.004E Switch ntpdate synchronization lost C 8400.005D Switch Upgrading License for SANdoctor C 8400.006A Switch Upgrading License for Fabric Security A license has become available and ports that had been previously timeout value has been reconfigured. EPorts will be automaticallyC 8700.0013 Connection failure, fabric limited to two switches Warning Events W 8400.003D Switch Invalid user username attempted to log into switch Informative Events I 8200.0201 mserver Rejecting request commandcommand I 8300.0009 Zoning Reading zoning database, Checkpoint not permitted The temperature threshold at which the switch issues a failure The temperature threshold at which the switch issues a warningI 8400.0048 Switch A CIM edit session has been canceled I 8F00.0008 Switch Removed I 8F00.0007 Switch AddedI 8F00.000B Login Changed I 8F00.000D Switch Status status59060-02 B 3 - Event Messages Informative Events3-50