QLogic Fibre Channel Switch Event Message Guide
Firmware Version
S i m p l i f y
Document Revision History
Revision B Changes
Document Sections Affected
1.3.3
Section
Introduction
Section 2 Events and Event Logging
Event Messages
Page
QLogic Fibre Channel Switch Event Message Guide
59060-02 B
Introduction
Intended Audience
Related Materials
Section
Availability
Technical Support
Training
Contact Information
Support Headquarters
North American Region
Europe, Middle East, and Africa Region
1 - Introduction Technical Support
59060-02 B
Displaying Events using the Event Browser
Events and Event Logging
Understanding Severity Levels
Section
Displaying the Events Using the Command Line Interface
Configuring the Event Log
Archiving and Downloading the Event Log
Configuring Port Alarm Thresholds
Alarm Events
Event Messages
Alarm Events Critical Events Warning Events
Section
A1003.000C Fabric Busy, failing lock request from domain domainID
A1003.000D Fabric already locked by domain domainID
A1003.000E Couldnt acquire lock from domain domainID
A1003.0010 Segmenting, zoneset zonesetname not defined
A1003.0013 Segmenting, zone zonename merge conflict
A1003.0021 Failing remote zoning configuration, Zoneset is empty
A1003.0025 Error reading security set
A1003.0029 No response received from switch with domain ID domainID
A1003.002A No response received from switch with domain ID domainID
A1003.002B No response received from switch with domain ID domainID
A1003.002F SW2 Zoning Not Supported by other switch, Isolating link
A1003.0030 Zone Merge rejected by remote switch
A1003.0031 Error reading zoneset from activate direct
A1003.0033 No memory for command completion
Remove zone sets from the local switch zoning database to allow
Reconcile interoperability modes on the local and remote switches
Remove members from the zone on the local switch or the remote
Remove zone members from the local switch or the remote switch
A remote switch sent a merge request that was not understood
A1003.003C Incompatible Zoning mode, Isolating link
A1003.0040 Zone Member type membertype unsupported
zone membership must be defined by domainID and port number
A1003.004D Port group does not contain entry for this switch
A1003.0050 ISL group does not contain entry for this switch
A1003.004F No Zone Merge Response
A1003.0048 Active Zone Set set if not already longer active
A1003.0051 Domain ID for local switch does not match fabric binding
A1003.0052 ISL group does not contain entry for switch domainID
A1003.0054 Failure at remote switch
A1003.0055 Problem on zoning save of following switches domainIDlist
A1003.0064 UFC failure received from domain domainID
A1004.000B Eport Isolating due to Switch Administratively Offline
A1004.0010 Eport Isolating due to Remote switch using same domain ID
An EPort isolated because each fabric has a switch with the same
An EPort isolated because the remote switch has the same
A1004.0011 Eport Isolating due to Remote switch isolated
A1004.0012 Eport Isolating due to ISL Security
A1004.0014 Eport Isolating due to TOV mismatch indicated on ELP
A1004.0015 Eport Isolating due to Invalid Attach
An attempt was made by a remote switch to connect through a port
An EPort isolated because the values for RATOV or EDTOV
licensing on the remote switch. Otherwise, contact your authorized
The switch with the specified worldwide name is not allowed to join
remote switch so that they are the same. Otherwise, contact your
binding indicates this domain is reserved for deviceWWN
A1004.0040
binding indicates it should use domainID
A1004.0041
A1004.0051 Blade IO bladenumber isolated due to startup problem
A1004.0052 Eport Isolating due to Switch Binding failure
limited to 64. If this number is exceeded, the switch cannot enforce
A1004.0048 Eport Isolating due to Port Binding failure
A1005.0013
AdminState
A1005.003B Warning - Debug logging filter level is set
A1006.0005 Zoning enforcement error in Nameserver
A1007.0001 NS Unspecified zoning enforcement error
A1007.0005 Security Authentication request was rejected by port
A1007.0002 Security WWN deviceWWN not authorized to join
A1007.0008 Security ESA Response failure, failing security checks
A1007.000C Security policy restrict mode, security db differs
A1007.001C Security Bad Authentication Flags
A1007.0025 Security feature not supported
A1007.0029 Security protocol not using chap, unable to authenticate
A1007.0030 Security protocol not using chap, unable to authenticate
A1007.0034 Device devicewwn failed switch binding
A1007.0038 Device devicewwn failed switch binding
An attempt to change the fabric binding setting was rejected due to
A1007.0033 Device deviceWWN failed port binding
A2000.0001
A3001.0001 Temp overwarm, sensorname sensor reads value C - ALARM SET
A3014.0003 Blade bladeID set Down due to blade type mismatch
A6001.0003 cmon switch failed NDCLA
switch. Contact technical support if a non-disruptive code load and
A6001.0001 cmon insufficient memory
A6001.0002 cmon blade failed NDCLA
Critical Events
C 8400.0005 Switch The switch is now performing a hotreset
C 8400.0015 Switch The switch will be reset in several seconds
C 8400.0045 Switch Upgrading License for 4G capability
C 8400.004E Switch ntpdate synchronization lost
C 8400.005D Switch Upgrading License for SANdoctor
C 8400.006A Switch Upgrading License for Fabric Security
timeout value has been reconfigured. EPorts will be automatically
A license has become available and ports that had been previously
C 8700.0013 Connection failure, fabric limited to two switches
Warning Events
W 8400.003D Switch Invalid user username attempted to log into switch
Informative Events
I 8200.0201 mserver Rejecting request commandcommand
I 8300.0009 Zoning Reading zoning database, Checkpoint not permitted
The temperature threshold at which the switch issues a warning
The temperature threshold at which the switch issues a failure
I 8400.0048 Switch A CIM edit session has been canceled
I 8F00.0007 Switch Added
I 8F00.0008 Switch Removed
I 8F00.000B Login Changed
I 8F00.000D Switch Status status
3-50
3 - Event Messages Informative Events
59060-02 B