Manuals / RAD Data comm / Computer Equipment / Network Card

RAD Data comm RIC-E1 operation manual Order from Cutter Networks Ph727-398-5252/Fax727-397-9610

Models: RIC-E1

1 99

Download 99 pages 62.9 Kb

Page 2

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 2

RAD Data comm RIC-E1 operation manual Order from Cutter Networks Ph727-398-5252/Fax727-397-9610

Contents

RIC-E1 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 RIC-E1 International Headquarters RAD Data Communications IncLimited Warranty General Safety Instructions Please observe the following precautionsConnection of DC Mains General Safety PracticesConnection of AC Mains Ports Safety Status IsdnElectromagnetic Compatibility EMC Canadian Emission Requirements Product Names SafetyManufacturers Name Manufacturers Address Supplementary InformationJumper Description Values Default Setting Installing RIC-E1Setting the Internal Jumpers Quick Start GuideTo connect cables Connecting the CablesOperating RIC-E1 Contents List of Figures Overview Power SupplyChapter Introduction VersionsPhysical Description ApplicationFunctional Description Functional Block DiagramDiagnostics Timing ReferenceDerived from three alternative sources Technical SpecificationsReceive, derived from the received signal Internal oscillatorPhysical DiagnosticsPower EnvironmentTechnical Specifications Site Requirements and Prerequisites Chapter Installation and SetupPackage Contents To install RIC-E1 Configuring RIC-E1Setting the Jumpers To set the jumpersRIC-E1 Jumper Locations RIC-E1 Jumper Settings Selecting the Impedance Connecting the InterfacesConnecting the E1 Line Closing the RIC-E1 CaseConnecting the AC Power Connecting the PowerConnecting the DTE Connecting the DC PowerInstallation and Setup Designation Color Function Front Panel IndicatorsChapter Operation Operating RIC-E1 Operating InstructionsTurning On Turning OffActivating Local Analog Loopback Chapter Troubleshooting DiagnosticsPerforming Local Analog Loopback Deactivating Local Analog Loopback TroubleshootingRIC-E1 Troubleshooting To activate the local analog loopback from RIC-E1/RTechnical Support Technical Support Chapter RIC-E1/R Card Line ConnectorDTE Connector ASM-MN-214 Card CageASM-MN-214 Rear Panel AC Supply Power SupplyPower Supply with Redundancy DC SupplyRIC-E1/R Front Panel IR-ETH or IR-ETHASM-MN-214 Front Panel RIC-E1/R PCB Layout RIC-E1/R Jumper Settings Installing the RIC-E1/R CardSetting Internal Jumpers and Switches Installing RIC-E1/R into the ASM-MN-214 Card Cage To install the RIC-E1/R card in the ASM-MN-214 card cageRIC-E1/R Card Appendix a Interface Connector Wiring V.35, X.21 and RS-530 Interface ConnectorsV.36 Interface Connector Signal Function 36, 37-Pin RS-530, 25-pin CircuitSignal Function 36, 37-pin RS-530, 25-pin Pin Circuit Line Interface ConnectorTable A-3. RJ-45 Line Interface Connector, Pin Assignment Pin FunctionAppendix a Interface Connector Wiring Introduction ContentsAppendix B IR-ETH Interface Module RIC-E1/R Card IR-ETH OptionsStandalone RIC-E1 Table B-1. RJ-45 PinoutFigure B-3. RIC-E1/R with IR-ETH Installation and Operation Table B-2. DIP Switch Settings Setting the DIP SwitchLED Indicators Link Connecting the LANTable B-4. IR-ETH LED Indicators, RIC-E1/R ACTContents Appendix C IR-ETH/V Interface ModuleIR-ETH/V Options Standalone RIC-E1RIC-E1 Throughput For example, MDI in OFF position, MDI is enabledMbps full duplex, 285 ∝s Data 00, 01, 02, …Moved by the user Table C-3. DIP Switch SW2 Settings Setting the DIP SwitchesTable C-2. DIP SW1 Switch Settings Section Name Description Possible Settings Factory SettingColor Function Table C-4. IR-ETH/V LED IndicatorsBackpressure and Flow Control Appendix D IR-IP Interface Module IntroductionAppendix D IR-IP Interface Module Protocols Connector 10BaseT Shielded RJ-45Standard Ieee 802.3/Ethernet Data Rate Frame Relay RFCRIC-E1/ IP Table D-1. IR-IP LEDs Functions Standalone RIC-E1 IR-IP LEDsIR-IP Controls Table D-2. IR-IP LEDs Functions RIC-E1/R CardTable D-3. IR-IP Controls Control Function Values Default SettingIR-IP Management Subsystem, General Table D-4 RJ-45 PinoutAccessing the IR-IP Management Subsystem Default IP Communication ParametersOutline of Preliminary Configuration Performing Preliminary ConfigurationRescue Configuration To allow the IR-IP configurationAssigning the Router LAN Interface Address Connecting the Telnet HostPreliminary Telnet Host Configuration IP Learning MechanismAssigning a LAN IP Address to a New IR-IP To view and edit the ARP table contentsTo configure the IP router LAN address What to Do If Changing the LAN IP Address of a Configured IR-IPAfter RIC-E1 is turned on, the ERR indicator does not light No ping replies from IR-IPStarting a Management Utility General Operating ProceduresIR-IP Management Utility Menu Structure of Management Utility Quick Setup MenuTo access the Quick Setup menu LAN IP Mask Default GatewayLAN IP Address WAN IP AddressTo configure the IR-IP as a Dhcp relay Read Protocol from DIP SwitchesOperation with Default Gateway Dhcp RelayTo access the Management Access menu Management Access MenuTelnet Password ProtocolTo access the Advanced Setup menu Advanced Setup MenuTelnet Inactivity Timeout To access the Device Identification menuDevice Name To access the Interface Parameters menuInterface Parameters Menu Contact PersonWAN Protocol Parameters Frame Relay Protocol Menu Header and Control Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Protocol Field CompressionMulticast IP Multicast Forwarding Figure D-17. Multicast IP MenuStatic Groups To access the Device Control menuDevice Control Viewing Error Log Screen New Software Download MenuResetting the Device Erasing ConfigurationResets Menu Resetting the LAN InterfaceTo access the Configuration and Connection screen Configuration and ConnectionTo access the View menu View MenuTo access the ARP Tables screen ARP TablesMulticast Groups Table Screen To access the Multicast Groups Table screenTo access the Statistics menu Displaying StatisticsDiagnostic Tools Ping Terminal To access the Diagnostic Tools menuUsing the Ping Function To ping a hostErasing IR-IP Software Erasing User’s ConfigurationTo erase the user’s configuration Desired positions, and then turn the RIC-E1 on againTo erase the application software Erasing Application SoftwareDownloading New Software Case, it is recommended to turn RIC-E1 off and then back onAppendix D IR-IP Interface Module Appendix E IR-X.21B Interface Module Rear PanelEXT Clock Mode Selecting the IR-X.21B TimingBuffer INT/LBT Clock ModeIR-X.21B Appendix E IR-X.21B Interface Module IP-IR Impedance, 2-4IndicatorsIndex IR-ETHRequirements, 2-1RIC-E1/R Card IR-IPLED Customer Response Form Excellent Good Fair Poor Very PoorError Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters