RAD Data comm RIC-E1 D.2 Technical Specifications

RIC-E1 Installation and Operation Manual Appendix D IR-IP Interface Module

Technical Specifications D-3

xDSL. Users on the LAN who register with the IR-IP for an IP multicast group using

the IGsMP protocol filter IP multicast packets at wire-speed.

Management and advanced configuration of the IR-IP module are performed via

Telnet.

Application

Figure D-1 shows a typical application of the RIC-E1 interface converter equipped

with the IR-IP module.

RIC-E1

10BaseT LAN

G.703

Network

Figure D-1. Typical Application of RIC-E1 with IR-IP Module

D.2 Technical Specifications

Router LAN IP net Up to 256 hosts on LAN IP net

Filtering and

Forwarding

30 kbps / 35 kbps

Buffer 25 6 frames (maximum size – 1534 bytes)

Delay 1 frame

LAN Standard IEEE 802.3/Ethernet V2

Data Rate 10 Mbps (20 Mbps 10BaseT in full duplex topology)

Connector 10BaseT: Shielded RJ-45

WAN Protocols • PPP (PAP/CHAP)

• Frame Relay (RFC 1490)

• HDLC

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Contents

Main Page RIC-E1 E1 Interface Converter Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Caution A Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Quick Start Guide 1. Installing RIC-E1 Setting the Internal Jumpers Connecting the Cables 2. Operating RIC-E1 RIC-E1 operates entirely unattended except when performing system tests. Contents List of Figures List of Tables Chapter 1 Introduction 1.1 Overview Versions DTE Interface Power Supply 1.2 Physical Description 1.3 Functional Description Functional Block Diagram Timing Reference Diagnostics 1.4 Technical Specifications Page Page Chapter 2 Installation and Setup 2.1 Site Requirements and Prerequisites 2.2 Package Contents 2.3 Configuring RIC-E1 Setting the Jumpers Figure 2-1. RIC-E1 Jumper Locations Table 2-1. RIC-E1 Jumper Settings Selecting the Impedance Closing the RIC-E1 Case Connecting the Interfaces Connecting the E1 Line Connecting the DTE Connecting the Power Connecting the AC Power Connecting the DC Power Page Chapter 3 Operation 3.1 Front Panel Indicators 3.2 Operating Instructions Chapter 4 Troubleshooting and Diagnostics 4.1 Performing Local Analog Loopback Activating Local Analog Loopback Deactivating Local Analog Loopback 4.2 Troubleshooting 4.3 Technical Support Page Chapter 5 RIC-E1/R Card 5.1 ASM-MN-214 Card Cage Line Connector DTE Connector Page 5.2 Power Supply AC Supply DC Supply Power Supply with Redundancy 5.3 RIC-E1/R Front Panel RIC-E1/ IP Page 5.4 Installing the RIC-E1/R Card Setting Internal Jumpers and Switches Figure 5-6 illustrates location of the internal jumpers on the RIC-E1/R PCB. Figure 5-6 RIC-E1/R PCB Layout Table 5-1. RIC-E1/R Jumper Settings Installing RIC-E1/R into the ASM-MN-214 Card Cage Connecting the Interfaces Page Appendix A Interface Connector Wiring A.1 V.35, X.21 and RS-530 Interface Connectors Table A-1. V.35, X.21 and RS-530 Interfaces, Pin Assignments (Cont.) A.2 V.36 Interface Connector Table A-2. Cable Converting between RS-530 and V.36 Interfaces, Pin Assignment (Cont.) A.3 Line Interface Connector Page Appendix B IR-ETH Interface Module Contents B.1 Introduction B.2 IR-ETH Options Page B.3 Technical Specifications B.4 Installation and Operation Setting the DIP Switch LED Indicators Connecting the LAN Appendix C IR-ETH/V Interface Module Contents C.1 Introduction C.2 IR-ETH/V Options Page C.3 Technical Specifications Bridge LAN Setting the DIP Switches Notes Reset RIC-E1 for changes in the flow control and LAN filtering switches to take effect. Table C-2. DIP SW1 Switch Settings Sections 2, 3, 7, and 8 of the SW1 DIP switch are factory-set and must not be moved by the user. LED Indicators Connecting the LAN Appendix D IR-IP Interface Module D.1 Introduction D.2 Technical Specifications D.3 Physical Description RIC-E1/IP IR-IP LEDs IR-IP Controls Table D-3. IR-IP Controls Table D-4 provides the pinout of the IR-IP RJ-45 connector. Table D-4. RJ-45 Pinout D.4 IR-IP Management Subsystem, General Accessing the IR-IP Management Subsystem Default IP Communication Parameters Rescue Configuration D.5 Performing Preliminary Configuration Outline of Preliminary Configuration Connecting the Telnet Host Preliminary Telnet Host Configuration Assigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP What to Do If ... D.6 IR-IP Management Utility General Operating Procedures Starting a Management Utility RIC-E1 Installation and Operation Manual Appendix D IR-IP Interface Module Quick Setup Menu D-13 D.7 Quick Setup Menu To access the Quick Setup menu: From the Main menu, type 1. The Quick Setup menu appears (Figure D-8). Figure D-8. Quick Setup Menu Order from: Cutter Networks LAN IP Address LAN IP Mask WAN IP Address DHCP Relay Read Protocol from DIP Switches Protocol D.8 Management Access Menu Telnet Password Telnet Inactivity Timeout D.9 Advanced Setup Menu Device Identification Menu Device Name Contact Person System Location Interface Parameters Menu LAN Status WAN Status WAN Throttle Aging Timeout WAN Protocol Parameters Frame Relay Protocol Menu Self Learn Maintenance Protocol DLCI CIR WAN Protocol Parameters PPP Protocol Header and Control Field Compression Protocol Field Compression Authentication Protocol Security Host/Guest Multicast IP Multicast Forwarding Static Groups D.10 Device Control New Software Download Menu Server IP Address File Name Total Timeout Start Operation Erasing Configuration Resets Menu Resetting the Device Resetting the LAN Interface Resetting the WAN Interface D.11 View Menu Configuration and Connection ARP Tables Multicast Groups Table Screen Displaying Statistics Figure D-27. WAN Statistics Screen D.12 Diagnostic Tools (Ping Terminal) This section provides information on the diagnostic tools provided with IR-IP. In the Main menu, type 6. The Diagnostic Tools menu appears (Figure D-28). Figure D-28. Diagnostic Tools Menu Using the Ping Function D.13 Erasing Users Configuration D.14 Erasing IR-IP Software Erasing Application Software Downloading New Software Page Appendix E IR-X.21B Interface Module Contents E.1 Introduction Application Rear Panel E.2 Selecting the IR-X.21B Timing EXT Clock Mode IR-X.21B RIC-E1 DTE INT/LBT Clock Mode IR-X.21B RIC-E1 DTE Page Index Page Customer Response Form Error Report