RAD Data comm RIC-E1 specs

RIC-E1Installation and Operation Manual	Appendix C IR-ETH/V Interface Module

RIC-E1/R Card

Figure C-3illustrates the front panel of RIC-E1/R with IR-ETH/V.

PWR

LINK

ACT

100M

LOS

RIC-E1

Figure C-3. RIC-E1/R with IR-ETH/V

IR-ETH/V Options

C-3

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 53

RAD Data comm RIC-E1 operation manual

Contents

RIC-E1 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters RAD Data Communications Inc RIC-E1 Limited Warranty Please observe the following precautions General Safety Instructions Connection of DC Mains General Safety PracticesConnection of AC Mains Isdn Ports Safety Status Electromagnetic Compatibility EMC Canadian Emission Requirements Manufacturers Name Manufacturers Address SafetyProduct Names Supplementary Information Setting the Internal Jumpers Installing RIC-E1Jumper Description Values Default Setting Quick Start Guide To connect cables Connecting the CablesOperating RIC-E1 Contents List of Figures Chapter Introduction Power SupplyOverview Versions Application Physical Description Diagnostics Functional Block DiagramFunctional Description Timing Reference Receive, derived from the received signal Technical SpecificationsDerived from three alternative sources Internal oscillator Power DiagnosticsPhysical Environment Technical Specifications Site Requirements and Prerequisites Chapter Installation and SetupPackage Contents Setting the Jumpers Configuring RIC-E1To install RIC-E1 To set the jumpers RIC-E1 Jumper Locations RIC-E1 Jumper Settings Connecting the E1 Line Connecting the InterfacesSelecting the Impedance Closing the RIC-E1 Case Connecting the DTE Connecting the PowerConnecting the AC Power Connecting the DC Power Installation and Setup Designation Color Function Front Panel IndicatorsChapter Operation Turning On Operating InstructionsOperating RIC-E1 Turning Off Activating Local Analog Loopback Chapter Troubleshooting DiagnosticsPerforming Local Analog Loopback RIC-E1 Troubleshooting TroubleshootingDeactivating Local Analog Loopback To activate the local analog loopback from RIC-E1/R Technical Support Technical Support DTE Connector Line ConnectorChapter RIC-E1/R Card ASM-MN-214 Card Cage ASM-MN-214 Rear Panel Power Supply with Redundancy Power SupplyAC Supply DC Supply IR-ETH or IR-ETH RIC-E1/R Front Panel ASM-MN-214 Front Panel RIC-E1/R PCB Layout RIC-E1/R Jumper Settings Installing the RIC-E1/R CardSetting Internal Jumpers and Switches To install the RIC-E1/R card in the ASM-MN-214 card cage Installing RIC-E1/R into the ASM-MN-214 Card Cage RIC-E1/R Card V.35, X.21 and RS-530 Interface Connectors Appendix a Interface Connector Wiring Signal Function 36, 37-Pin RS-530, 25-pin Circuit V.36 Interface Connector Table A-3. RJ-45 Line Interface Connector, Pin Assignment Line Interface ConnectorSignal Function 36, 37-pin RS-530, 25-pin Pin Circuit Pin Function Appendix a Interface Connector Wiring Introduction ContentsAppendix B IR-ETH Interface Module Standalone RIC-E1 IR-ETH OptionsRIC-E1/R Card Table B-1. RJ-45 Pinout Figure B-3. RIC-E1/R with IR-ETH Installation and Operation Table B-2. DIP Switch Settings Setting the DIP SwitchLED Indicators Table B-4. IR-ETH LED Indicators, RIC-E1/R Connecting the LANLink ACT Appendix C IR-ETH/V Interface Module IR-ETH/V Options RIC-E1 Mbps full duplex, 285 ∝s For example, MDI in OFF position, MDI is enabledThroughput Data 00, 01, 02, … Table C-2. DIP SW1 Switch Settings Setting the DIP SwitchesMoved by the user Table C-3. DIP Switch SW2 Settings Section Name Description Possible Settings Factory Setting Color Function Table C-4. IR-ETH/V LED IndicatorsBackpressure and Flow Control Introduction Appendix D IR-IP Interface Module Appendix D IR-IP Interface Module Standard Ieee 802.3/Ethernet Data Rate Connector 10BaseT Shielded RJ-45Protocols Frame Relay RFC RIC-E1/ IP IR-IP Controls IR-IP LEDsTable D-1. IR-IP LEDs Functions Standalone RIC-E1 Table D-2. IR-IP LEDs Functions RIC-E1/R Card IR-IP Management Subsystem, General Control Function Values Default SettingTable D-3. IR-IP Controls Table D-4 RJ-45 Pinout Default IP Communication Parameters Accessing the IR-IP Management Subsystem Rescue Configuration Performing Preliminary ConfigurationOutline of Preliminary Configuration To allow the IR-IP configuration Preliminary Telnet Host Configuration Connecting the Telnet HostAssigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP To view and edit the ARP table contentsTo configure the IP router LAN address After RIC-E1 is turned on, the ERR indicator does not light Changing the LAN IP Address of a Configured IR-IPWhat to Do If No ping replies from IR-IP Starting a Management Utility General Operating ProceduresIR-IP Management Utility Menu Structure of Management Utility Quick Setup MenuTo access the Quick Setup menu LAN IP Address Default GatewayLAN IP Mask WAN IP Address Operation with Default Gateway Read Protocol from DIP SwitchesTo configure the IR-IP as a Dhcp relay Dhcp Relay Telnet Password Management Access MenuTo access the Management Access menu Protocol Telnet Inactivity Timeout Advanced Setup MenuTo access the Advanced Setup menu To access the Device Identification menu Interface Parameters Menu To access the Interface Parameters menuDevice Name Contact Person WAN Protocol Parameters Frame Relay Protocol Menu WAN Protocol Parameters PPP Protocol Authentication ProtocolHeader and Control Field Compression Protocol Field Compression Multicast IP Figure D-17. Multicast IP Menu Multicast Forwarding Static Groups To access the Device Control menuDevice Control New Software Download Menu Viewing Error Log Screen Resets Menu Erasing ConfigurationResetting the Device Resetting the LAN Interface To access the View menu Configuration and ConnectionTo access the Configuration and Connection screen View Menu ARP Tables To access the ARP Tables screen To access the Statistics menu To access the Multicast Groups Table screenMulticast Groups Table Screen Displaying Statistics To access the Diagnostic Tools menu Diagnostic Tools Ping Terminal To ping a host Using the Ping Function To erase the user’s configuration Erasing User’s ConfigurationErasing IR-IP Software Desired positions, and then turn the RIC-E1 on again Downloading New Software Erasing Application SoftwareTo erase the application software Case, it is recommended to turn RIC-E1 off and then back on Appendix D IR-IP Interface Module Rear Panel Appendix E IR-X.21B Interface Module Selecting the IR-X.21B Timing EXT Clock Mode Buffer INT/LBT Clock ModeIR-X.21B Appendix E IR-X.21B Interface Module Index Impedance, 2-4IndicatorsIP-IR IR-ETH Requirements, 2-1RIC-E1/R Card IR-IPLED Excellent Good Fair Poor Very Poor Customer Response Form Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters