Technical Support | RAD Data comm RIC-E1 instruction

RIC-E1Installation and Operation Manual		Chapter 4 Troubleshooting and Diagnostics

4.3 Technical Support

Technical support for this product can be obtained from the local distributor from whom it was purchased.

For further information, please contact the RAD distributor nearest you or one of RAD's offices worldwide.

Technical Support

4-3

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Page 31

Image 31

RAD Data comm RIC-E1 operation manual Technical Support

Contents

RIC-E1 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters RAD Data Communications Inc RIC-E1 Limited Warranty Please observe the following precautions General Safety Instructions Connection of AC Mains General Safety PracticesConnection of DC Mains Isdn Ports Safety Status Electromagnetic Compatibility EMC Canadian Emission Requirements Supplementary Information SafetyManufacturers Name Manufacturers Address Product Names Quick Start Guide Installing RIC-E1Setting the Internal Jumpers Jumper Description Values Default Setting Operating RIC-E1 Connecting the CablesTo connect cables Contents List of Figures Versions Power SupplyChapter Introduction Overview Application Physical Description Timing Reference Functional Block DiagramDiagnostics Functional Description Internal oscillator Technical SpecificationsReceive, derived from the received signal Derived from three alternative sources Environment DiagnosticsPower Physical Technical Specifications Package Contents Chapter Installation and SetupSite Requirements and Prerequisites To set the jumpers Configuring RIC-E1Setting the Jumpers To install RIC-E1 RIC-E1 Jumper Locations RIC-E1 Jumper Settings Closing the RIC-E1 Case Connecting the InterfacesConnecting the E1 Line Selecting the Impedance Connecting the DC Power Connecting the PowerConnecting the DTE Connecting the AC Power Installation and Setup Chapter Operation Front Panel IndicatorsDesignation Color Function Turning Off Operating InstructionsTurning On Operating RIC-E1 Performing Local Analog Loopback Chapter Troubleshooting DiagnosticsActivating Local Analog Loopback To activate the local analog loopback from RIC-E1/R TroubleshootingRIC-E1 Troubleshooting Deactivating Local Analog Loopback Technical Support Technical Support ASM-MN-214 Card Cage Line ConnectorDTE Connector Chapter RIC-E1/R Card ASM-MN-214 Rear Panel DC Supply Power SupplyPower Supply with Redundancy AC Supply IR-ETH or IR-ETH RIC-E1/R Front Panel ASM-MN-214 Front Panel Setting Internal Jumpers and Switches Installing the RIC-E1/R CardRIC-E1/R PCB Layout RIC-E1/R Jumper Settings To install the RIC-E1/R card in the ASM-MN-214 card cage Installing RIC-E1/R into the ASM-MN-214 Card Cage RIC-E1/R Card V.35, X.21 and RS-530 Interface Connectors Appendix a Interface Connector Wiring Signal Function 36, 37-Pin RS-530, 25-pin Circuit V.36 Interface Connector Pin Function Line Interface ConnectorTable A-3. RJ-45 Line Interface Connector, Pin Assignment Signal Function 36, 37-pin RS-530, 25-pin Pin Circuit Appendix a Interface Connector Wiring Appendix B IR-ETH Interface Module ContentsIntroduction Table B-1. RJ-45 Pinout IR-ETH OptionsStandalone RIC-E1 RIC-E1/R Card Figure B-3. RIC-E1/R with IR-ETH Installation and Operation LED Indicators Setting the DIP SwitchTable B-2. DIP Switch Settings ACT Connecting the LANTable B-4. IR-ETH LED Indicators, RIC-E1/R Link Appendix C IR-ETH/V Interface Module IR-ETH/V Options RIC-E1 Data 00, 01, 02, … For example, MDI in OFF position, MDI is enabledMbps full duplex, 285 ∝s Throughput Section Name Description Possible Settings Factory Setting Setting the DIP SwitchesTable C-2. DIP SW1 Switch Settings Moved by the user Table C-3. DIP Switch SW2 Settings Backpressure and Flow Control Table C-4. IR-ETH/V LED IndicatorsColor Function Introduction Appendix D IR-IP Interface Module Appendix D IR-IP Interface Module Frame Relay RFC Connector 10BaseT Shielded RJ-45Standard Ieee 802.3/Ethernet Data Rate Protocols RIC-E1/ IP Table D-2. IR-IP LEDs Functions RIC-E1/R Card IR-IP LEDsIR-IP Controls Table D-1. IR-IP LEDs Functions Standalone RIC-E1 Table D-4 RJ-45 Pinout Control Function Values Default SettingIR-IP Management Subsystem, General Table D-3. IR-IP Controls Default IP Communication Parameters Accessing the IR-IP Management Subsystem To allow the IR-IP configuration Performing Preliminary ConfigurationRescue Configuration Outline of Preliminary Configuration IP Learning Mechanism Connecting the Telnet HostPreliminary Telnet Host Configuration Assigning the Router LAN Interface Address To configure the IP router LAN address To view and edit the ARP table contentsAssigning a LAN IP Address to a New IR-IP No ping replies from IR-IP Changing the LAN IP Address of a Configured IR-IPAfter RIC-E1 is turned on, the ERR indicator does not light What to Do If IR-IP Management Utility General Operating ProceduresStarting a Management Utility To access the Quick Setup menu Quick Setup MenuMenu Structure of Management Utility WAN IP Address Default GatewayLAN IP Address LAN IP Mask Dhcp Relay Read Protocol from DIP SwitchesOperation with Default Gateway To configure the IR-IP as a Dhcp relay Protocol Management Access MenuTelnet Password To access the Management Access menu To access the Device Identification menu Advanced Setup MenuTelnet Inactivity Timeout To access the Advanced Setup menu Contact Person To access the Interface Parameters menuInterface Parameters Menu Device Name WAN Protocol Parameters Frame Relay Protocol Menu Protocol Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Header and Control Field Compression Multicast IP Figure D-17. Multicast IP Menu Multicast Forwarding Device Control To access the Device Control menuStatic Groups New Software Download Menu Viewing Error Log Screen Resetting the LAN Interface Erasing ConfigurationResets Menu Resetting the Device View Menu Configuration and ConnectionTo access the View menu To access the Configuration and Connection screen ARP Tables To access the ARP Tables screen Displaying Statistics To access the Multicast Groups Table screenTo access the Statistics menu Multicast Groups Table Screen To access the Diagnostic Tools menu Diagnostic Tools Ping Terminal To ping a host Using the Ping Function Desired positions, and then turn the RIC-E1 on again Erasing User’s ConfigurationTo erase the user’s configuration Erasing IR-IP Software Case, it is recommended to turn RIC-E1 off and then back on Erasing Application SoftwareDownloading New Software To erase the application software Appendix D IR-IP Interface Module Rear Panel Appendix E IR-X.21B Interface Module Selecting the IR-X.21B Timing EXT Clock Mode IR-X.21B INT/LBT Clock ModeBuffer Appendix E IR-X.21B Interface Module IR-ETH Impedance, 2-4IndicatorsIndex IP-IR LED IR-IPRequirements, 2-1RIC-E1/R Card Excellent Good Fair Poor Very Poor Customer Response Form Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters