RAD Data comm RIC-E1 Setting the DIP Switches

RIC-E1 Installation and Operation Manual Appendix C IR-ETH/V Interface Module

Installation and Operation C-5

Setting the DIP Switches

Configure the IR-ETH/V module by setting the DIP switches SW1 and SW2 in

accordance with Figure C-4, Table C-2 and Table C-3.

Reset RIC-E1 for changes in the flow control and LAN filtering switches to take effect.

Table C-2. DIP SW1 Switch Settings

Section Name Description Possible Settings Factory Setting

1 MDI Enables or disables

automatic MDI/MDIX

crossover

ON – Automatic MDI/MDIX crossover

is disabled

OFF – Automatic MDI/MDIX

crossover is enabled

OFF

2, 3 NC – – –

FLC Enables or disables flow

control (full duplex) /

backpressure (half

duplex)

4

Note: Flow Control (full duplex) is active

only if autonegotiation is enabled

ON – Flow control/Backpressure is

enabled

OFF – Flow control/Backpressure is

disabled

ON

5 FIL

Enable or disable LAN

filtering

ON – LAN filtering is disabled

OFF – LAN filtering is enabled

OFF

6 FP

Enable or disable fault

propagation

ON – Fault propagation is disabled

OFF – Fault propagation is enabled

ON

Note: When fault propagation is enabled, the LAN interface shuts down if a failure is detected on the E1 line.

When fault propagation is disabled, the link integrity is not influenced by the E1 behavior.

7, 8 NC

Sections 2, 3, 7, and 8 of the SW1 DIP switch are factory-set and must not be

moved by the user.

Table C-3. DIP Switch SW2 Settings

Section Name Description Possible Settings Factory Setting

1 100 Selects the LAN speed ON – LAN speed is set to 10 Mbps

OFF – LAN speed is set to 100 Mbps

OFF

2 AN Controls the LAN

autonegotiation

ON – LAN autonegotiation is disabled

OFF – LAN autonegotiation is enabled

OFF

3 FDX Selects the LAN duplex

mode

ON – LAN half duplex mode

OFF – LAN full duplex mode

OFF

4, 5, 6 NC

• Sections 4, 5, and 6 of the SW2 DIP switch are factory-set an d must not be

moved by the user.

• When autonegotiation is enabled, LAN speed and LAN duplex mode are

configured automatically (sections 1 and 3 are disabled).

Note

Notes

Note

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Contents

Main Page RIC-E1 E1 Interface Converter Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Caution A Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Quick Start Guide 1. Installing RIC-E1 Setting the Internal Jumpers Connecting the Cables 2. Operating RIC-E1 RIC-E1 operates entirely unattended except when performing system tests. Contents List of Figures List of Tables Chapter 1 Introduction 1.1 Overview Versions DTE Interface Power Supply 1.2 Physical Description 1.3 Functional Description Functional Block Diagram Timing Reference Diagnostics 1.4 Technical Specifications Page Page Chapter 2 Installation and Setup 2.1 Site Requirements and Prerequisites 2.2 Package Contents 2.3 Configuring RIC-E1 Setting the Jumpers Figure 2-1. RIC-E1 Jumper Locations Table 2-1. RIC-E1 Jumper Settings Selecting the Impedance Closing the RIC-E1 Case Connecting the Interfaces Connecting the E1 Line Connecting the DTE Connecting the Power Connecting the AC Power Connecting the DC Power Page Chapter 3 Operation 3.1 Front Panel Indicators 3.2 Operating Instructions Chapter 4 Troubleshooting and Diagnostics 4.1 Performing Local Analog Loopback Activating Local Analog Loopback Deactivating Local Analog Loopback 4.2 Troubleshooting 4.3 Technical Support Page Chapter 5 RIC-E1/R Card 5.1 ASM-MN-214 Card Cage Line Connector DTE Connector Page 5.2 Power Supply AC Supply DC Supply Power Supply with Redundancy 5.3 RIC-E1/R Front Panel RIC-E1/ IP Page 5.4 Installing the RIC-E1/R Card Setting Internal Jumpers and Switches Figure 5-6 illustrates location of the internal jumpers on the RIC-E1/R PCB. Figure 5-6 RIC-E1/R PCB Layout Table 5-1. RIC-E1/R Jumper Settings Installing RIC-E1/R into the ASM-MN-214 Card Cage Connecting the Interfaces Page Appendix A Interface Connector Wiring A.1 V.35, X.21 and RS-530 Interface Connectors Table A-1. V.35, X.21 and RS-530 Interfaces, Pin Assignments (Cont.) A.2 V.36 Interface Connector Table A-2. Cable Converting between RS-530 and V.36 Interfaces, Pin Assignment (Cont.) A.3 Line Interface Connector Page Appendix B IR-ETH Interface Module Contents B.1 Introduction B.2 IR-ETH Options Page B.3 Technical Specifications B.4 Installation and Operation Setting the DIP Switch LED Indicators Connecting the LAN Appendix C IR-ETH/V Interface Module Contents C.1 Introduction C.2 IR-ETH/V Options Page C.3 Technical Specifications Bridge LAN Setting the DIP Switches Notes Reset RIC-E1 for changes in the flow control and LAN filtering switches to take effect. Table C-2. DIP SW1 Switch Settings Sections 2, 3, 7, and 8 of the SW1 DIP switch are factory-set and must not be moved by the user. LED Indicators Connecting the LAN Appendix D IR-IP Interface Module D.1 Introduction D.2 Technical Specifications D.3 Physical Description RIC-E1/IP IR-IP LEDs IR-IP Controls Table D-3. IR-IP Controls Table D-4 provides the pinout of the IR-IP RJ-45 connector. Table D-4. RJ-45 Pinout D.4 IR-IP Management Subsystem, General Accessing the IR-IP Management Subsystem Default IP Communication Parameters Rescue Configuration D.5 Performing Preliminary Configuration Outline of Preliminary Configuration Connecting the Telnet Host Preliminary Telnet Host Configuration Assigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP What to Do If ... D.6 IR-IP Management Utility General Operating Procedures Starting a Management Utility RIC-E1 Installation and Operation Manual Appendix D IR-IP Interface Module Quick Setup Menu D-13 D.7 Quick Setup Menu To access the Quick Setup menu: From the Main menu, type 1. The Quick Setup menu appears (Figure D-8). Figure D-8. Quick Setup Menu Order from: Cutter Networks LAN IP Address LAN IP Mask WAN IP Address DHCP Relay Read Protocol from DIP Switches Protocol D.8 Management Access Menu Telnet Password Telnet Inactivity Timeout D.9 Advanced Setup Menu Device Identification Menu Device Name Contact Person System Location Interface Parameters Menu LAN Status WAN Status WAN Throttle Aging Timeout WAN Protocol Parameters Frame Relay Protocol Menu Self Learn Maintenance Protocol DLCI CIR WAN Protocol Parameters PPP Protocol Header and Control Field Compression Protocol Field Compression Authentication Protocol Security Host/Guest Multicast IP Multicast Forwarding Static Groups D.10 Device Control New Software Download Menu Server IP Address File Name Total Timeout Start Operation Erasing Configuration Resets Menu Resetting the Device Resetting the LAN Interface Resetting the WAN Interface D.11 View Menu Configuration and Connection ARP Tables Multicast Groups Table Screen Displaying Statistics Figure D-27. WAN Statistics Screen D.12 Diagnostic Tools (Ping Terminal) This section provides information on the diagnostic tools provided with IR-IP. In the Main menu, type 6. The Diagnostic Tools menu appears (Figure D-28). Figure D-28. Diagnostic Tools Menu Using the Ping Function D.13 Erasing Users Configuration D.14 Erasing IR-IP Software Erasing Application Software Downloading New Software Page Appendix E IR-X.21B Interface Module Contents E.1 Introduction Application Rear Panel E.2 Selecting the IR-X.21B Timing EXT Clock Mode IR-X.21B RIC-E1 DTE INT/LBT Clock Mode IR-X.21B RIC-E1 DTE Page Index Page Customer Response Form Error Report