Manuals / Brands / Computer Equipment / Network Card / RAD Data comm / Computer Equipment / Network Card

RAD Data comm RIC-E1 Installing RIC-E1/R into the ASM-MN-214 Card Cage , Connecting the Interfaces

1 99

Download 99 pages, 3.88 Mb

RIC-E1 Installation and Operation Manual Chapter 5 RIC-E1/R Card

Installing the RIC-E1/R Card 5-7

Table 5-1. RIC-E1/R Jumper Settings (Cont.)

Jumper Description Values Default Setting

PNL SW, JP5 Enables activation of the

local analog loopback via

the front panel pushbutton

EN – The LLB can be activated via

the front panel

DIS – The LLB cannot be

activated via the front

panel

EN

Note: The JP5 jumper is not available for RIC-E1/R cards with IR-ETH and IR-ETH/V interface modules.

For RIC-E1/R with IR-IP interface module, the JP5 jumper serves for enabling or disabling the IP LEARN

pushbutton.

TX&RX CODE, JP6 Selects the data receive

and transmit coding

HDB3

AMI

HDB3

TIMING SEL, J2 Selects the clock reference RCV – Receive clock

EXT – External clock

INT – Internal clock

RCV

Note: Units with the IR-ETH, IR-ETH/V and IR-IP interface modules support only receive and internal clocks.

CHASS GND, J3 Controls the connection

between the RIC-E1/R

signal ground and the

frame (chassis) ground

CON – Signal ground is

connected to the frame

ground

DISCON – Signal ground is

disconnected from the

frame ground

CON

Installing RIC-E1/R into the ASM-MN-214 Card Cage

 To install the RIC-E1/R card in the ASM-MN-214 card cage:

1. Install the ASM-MN-214 card cage in the 19-inch rack.

2. Insert the RIC-E1/R card into one of the ASM-MN-214 slots.

3. Push the card into the cage until it is fully inserted into the edge connector

inside the rack.

4. Tighten the screws on front panel of the modem card.

Connecting the Interfaces

RIC-E1/R uses the ASM-MN-214 rear panel terminal block ports for the line

connections. The 25-pin D-type female connector serves as a DTE port.

1. Remove the protection cover from the terminal block connectors.

2. Connect the terminal block to the ASM-MN-214 terminal block connector.

3. Connect the line to the terminal block as follows: connect transmit pair to the

terminals marked XMT, the receive pair to the terminals marked RCV, and the

fifth screw to ground (optional).

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Contents

Main Page RIC-E1 E1 Interface Converter Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Caution A Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Quick Start Guide 1. Installing RIC-E1 Setting the Internal Jumpers Connecting the Cables 2. Operating RIC-E1 RIC-E1 operates entirely unattended except when performing system tests. Contents List of Figures List of Tables Chapter 1 Introduction 1.1 Overview Versions DTE Interface Power Supply 1.2 Physical Description 1.3 Functional Description Functional Block Diagram Timing Reference Diagnostics 1.4 Technical Specifications Page Page Chapter 2 Installation and Setup 2.1 Site Requirements and Prerequisites 2.2 Package Contents 2.3 Configuring RIC-E1 Setting the Jumpers Figure 2-1. RIC-E1 Jumper Locations Table 2-1. RIC-E1 Jumper Settings Selecting the Impedance Closing the RIC-E1 Case Connecting the Interfaces Connecting the E1 Line Connecting the DTE Connecting the Power Connecting the AC Power Connecting the DC Power Page Chapter 3 Operation 3.1 Front Panel Indicators 3.2 Operating Instructions Chapter 4 Troubleshooting and Diagnostics 4.1 Performing Local Analog Loopback Activating Local Analog Loopback Deactivating Local Analog Loopback 4.2 Troubleshooting 4.3 Technical Support Page Chapter 5 RIC-E1/R Card 5.1 ASM-MN-214 Card Cage Line Connector DTE Connector Page 5.2 Power Supply AC Supply DC Supply Power Supply with Redundancy 5.3 RIC-E1/R Front Panel RIC-E1/ IP Page 5.4 Installing the RIC-E1/R Card Setting Internal Jumpers and Switches Figure 5-6 illustrates location of the internal jumpers on the RIC-E1/R PCB. Figure 5-6 RIC-E1/R PCB Layout Table 5-1. RIC-E1/R Jumper Settings Installing RIC-E1/R into the ASM-MN-214 Card Cage Connecting the Interfaces Page Appendix A Interface Connector Wiring A.1 V.35, X.21 and RS-530 Interface Connectors Table A-1. V.35, X.21 and RS-530 Interfaces, Pin Assignments (Cont.) A.2 V.36 Interface Connector Table A-2. Cable Converting between RS-530 and V.36 Interfaces, Pin Assignment (Cont.) A.3 Line Interface Connector Page Appendix B IR-ETH Interface Module Contents B.1 Introduction B.2 IR-ETH Options Page B.3 Technical Specifications B.4 Installation and Operation Setting the DIP Switch LED Indicators Connecting the LAN Appendix C IR-ETH/V Interface Module Contents C.1 Introduction C.2 IR-ETH/V Options Page C.3 Technical Specifications Bridge LAN Setting the DIP Switches Notes Reset RIC-E1 for changes in the flow control and LAN filtering switches to take effect. Table C-2. DIP SW1 Switch Settings Sections 2, 3, 7, and 8 of the SW1 DIP switch are factory-set and must not be moved by the user. LED Indicators Connecting the LAN Appendix D IR-IP Interface Module D.1 Introduction D.2 Technical Specifications D.3 Physical Description RIC-E1/IP IR-IP LEDs IR-IP Controls Table D-3. IR-IP Controls Table D-4 provides the pinout of the IR-IP RJ-45 connector. Table D-4. RJ-45 Pinout D.4 IR-IP Management Subsystem, General Accessing the IR-IP Management Subsystem Default IP Communication Parameters Rescue Configuration D.5 Performing Preliminary Configuration Outline of Preliminary Configuration Connecting the Telnet Host Preliminary Telnet Host Configuration Assigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP What to Do If ... D.6 IR-IP Management Utility General Operating Procedures Starting a Management Utility RIC-E1 Installation and Operation Manual Appendix D IR-IP Interface Module Quick Setup Menu D-13 D.7 Quick Setup Menu To access the Quick Setup menu: From the Main menu, type 1. The Quick Setup menu appears (Figure D-8). Figure D-8. Quick Setup Menu Order from: Cutter Networks LAN IP Address LAN IP Mask WAN IP Address DHCP Relay Read Protocol from DIP Switches Protocol D.8 Management Access Menu Telnet Password Telnet Inactivity Timeout D.9 Advanced Setup Menu Device Identification Menu Device Name Contact Person System Location Interface Parameters Menu LAN Status WAN Status WAN Throttle Aging Timeout WAN Protocol Parameters Frame Relay Protocol Menu Self Learn Maintenance Protocol DLCI CIR WAN Protocol Parameters PPP Protocol Header and Control Field Compression Protocol Field Compression Authentication Protocol Security Host/Guest Multicast IP Multicast Forwarding Static Groups D.10 Device Control New Software Download Menu Server IP Address File Name Total Timeout Start Operation Erasing Configuration Resets Menu Resetting the Device Resetting the LAN Interface Resetting the WAN Interface D.11 View Menu Configuration and Connection ARP Tables Multicast Groups Table Screen Displaying Statistics Figure D-27. WAN Statistics Screen D.12 Diagnostic Tools (Ping Terminal) This section provides information on the diagnostic tools provided with IR-IP. In the Main menu, type 6. The Diagnostic Tools menu appears (Figure D-28). Figure D-28. Diagnostic Tools Menu Using the Ping Function D.13 Erasing Users Configuration D.14 Erasing IR-IP Software Erasing Application Software Downloading New Software Page Appendix E IR-X.21B Interface Module Contents E.1 Introduction Application Rear Panel E.2 Selecting the IR-X.21B Timing EXT Clock Mode IR-X.21B RIC-E1 DTE INT/LBT Clock Mode IR-X.21B RIC-E1 DTE Page Index Page Customer Response Form Error Report