International Headquarters | RAD Data comm RIC-E1 guide

www.rad.com

INTERNATIONAL HEADQUARTERS:

24Raoul Wallenberg Street, Tel Aviv 69719, Israel, Tel: 972-3-6458181 Fax: 972-3-6498250, 972-3-6474436, Email: market@rad.com

U.S. HEADQUARTERS:

900 Corporate Drive, Mahwah, N.J. 07430, Tel: (201) 529-1100

Toll Free: 1-800-444-7234, Fax: (201) 529-5777, Email: market@radusa.com

Publication No. 269-200-12/04

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 99

RAD Data comm RIC-E1 operation manual International Headquarters

Contents

RIC-E1 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters RAD Data Communications Inc RIC-E1 Limited Warranty Please observe the following precautions General Safety Instructions General Safety Practices Connection of AC MainsConnection of DC Mains Isdn Ports Safety Status Electromagnetic Compatibility EMC Canadian Emission Requirements Supplementary Information SafetyManufacturers Name Manufacturers Address Product Names Quick Start Guide Installing RIC-E1Setting the Internal Jumpers Jumper Description Values Default Setting Connecting the Cables Operating RIC-E1To connect cables Contents List of Figures Versions Power SupplyChapter Introduction Overview Application Physical Description Timing Reference Functional Block DiagramDiagnostics Functional Description Internal oscillator Technical SpecificationsReceive, derived from the received signal Derived from three alternative sources Environment DiagnosticsPower Physical Technical Specifications Chapter Installation and Setup Package ContentsSite Requirements and Prerequisites To set the jumpers Configuring RIC-E1Setting the Jumpers To install RIC-E1 RIC-E1 Jumper Locations RIC-E1 Jumper Settings Closing the RIC-E1 Case Connecting the InterfacesConnecting the E1 Line Selecting the Impedance Connecting the DC Power Connecting the PowerConnecting the DTE Connecting the AC Power Installation and Setup Front Panel Indicators Chapter OperationDesignation Color Function Turning Off Operating InstructionsTurning On Operating RIC-E1 Chapter Troubleshooting Diagnostics Performing Local Analog LoopbackActivating Local Analog Loopback To activate the local analog loopback from RIC-E1/R TroubleshootingRIC-E1 Troubleshooting Deactivating Local Analog Loopback Technical Support Technical Support ASM-MN-214 Card Cage Line ConnectorDTE Connector Chapter RIC-E1/R Card ASM-MN-214 Rear Panel DC Supply Power SupplyPower Supply with Redundancy AC Supply IR-ETH or IR-ETH RIC-E1/R Front Panel ASM-MN-214 Front Panel Installing the RIC-E1/R Card Setting Internal Jumpers and SwitchesRIC-E1/R PCB Layout RIC-E1/R Jumper Settings To install the RIC-E1/R card in the ASM-MN-214 card cage Installing RIC-E1/R into the ASM-MN-214 Card Cage RIC-E1/R Card V.35, X.21 and RS-530 Interface Connectors Appendix a Interface Connector Wiring Signal Function 36, 37-Pin RS-530, 25-pin Circuit V.36 Interface Connector Pin Function Line Interface ConnectorTable A-3. RJ-45 Line Interface Connector, Pin Assignment Signal Function 36, 37-pin RS-530, 25-pin Pin Circuit Appendix a Interface Connector Wiring Contents Appendix B IR-ETH Interface ModuleIntroduction Table B-1. RJ-45 Pinout IR-ETH OptionsStandalone RIC-E1 RIC-E1/R Card Figure B-3. RIC-E1/R with IR-ETH Installation and Operation Setting the DIP Switch LED IndicatorsTable B-2. DIP Switch Settings ACT Connecting the LANTable B-4. IR-ETH LED Indicators, RIC-E1/R Link Appendix C IR-ETH/V Interface Module IR-ETH/V Options RIC-E1 Data 00, 01, 02, … For example, MDI in OFF position, MDI is enabledMbps full duplex, 285 ∝s Throughput Section Name Description Possible Settings Factory Setting Setting the DIP SwitchesTable C-2. DIP SW1 Switch Settings Moved by the user Table C-3. DIP Switch SW2 Settings Table C-4. IR-ETH/V LED Indicators Backpressure and Flow ControlColor Function Introduction Appendix D IR-IP Interface Module Appendix D IR-IP Interface Module Frame Relay RFC Connector 10BaseT Shielded RJ-45Standard Ieee 802.3/Ethernet Data Rate Protocols RIC-E1/ IP Table D-2. IR-IP LEDs Functions RIC-E1/R Card IR-IP LEDsIR-IP Controls Table D-1. IR-IP LEDs Functions Standalone RIC-E1 Table D-4 RJ-45 Pinout Control Function Values Default SettingIR-IP Management Subsystem, General Table D-3. IR-IP Controls Default IP Communication Parameters Accessing the IR-IP Management Subsystem To allow the IR-IP configuration Performing Preliminary ConfigurationRescue Configuration Outline of Preliminary Configuration IP Learning Mechanism Connecting the Telnet HostPreliminary Telnet Host Configuration Assigning the Router LAN Interface Address To view and edit the ARP table contents To configure the IP router LAN addressAssigning a LAN IP Address to a New IR-IP No ping replies from IR-IP Changing the LAN IP Address of a Configured IR-IPAfter RIC-E1 is turned on, the ERR indicator does not light What to Do If General Operating Procedures IR-IP Management UtilityStarting a Management Utility Quick Setup Menu To access the Quick Setup menuMenu Structure of Management Utility WAN IP Address Default GatewayLAN IP Address LAN IP Mask Dhcp Relay Read Protocol from DIP SwitchesOperation with Default Gateway To configure the IR-IP as a Dhcp relay Protocol Management Access MenuTelnet Password To access the Management Access menu To access the Device Identification menu Advanced Setup MenuTelnet Inactivity Timeout To access the Advanced Setup menu Contact Person To access the Interface Parameters menuInterface Parameters Menu Device Name WAN Protocol Parameters Frame Relay Protocol Menu Protocol Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Header and Control Field Compression Multicast IP Figure D-17. Multicast IP Menu Multicast Forwarding To access the Device Control menu Device ControlStatic Groups New Software Download Menu Viewing Error Log Screen Resetting the LAN Interface Erasing ConfigurationResets Menu Resetting the Device View Menu Configuration and ConnectionTo access the View menu To access the Configuration and Connection screen ARP Tables To access the ARP Tables screen Displaying Statistics To access the Multicast Groups Table screenTo access the Statistics menu Multicast Groups Table Screen To access the Diagnostic Tools menu Diagnostic Tools Ping Terminal To ping a host Using the Ping Function Desired positions, and then turn the RIC-E1 on again Erasing User’s ConfigurationTo erase the user’s configuration Erasing IR-IP Software Case, it is recommended to turn RIC-E1 off and then back on Erasing Application SoftwareDownloading New Software To erase the application software Appendix D IR-IP Interface Module Rear Panel Appendix E IR-X.21B Interface Module Selecting the IR-X.21B Timing EXT Clock Mode INT/LBT Clock Mode IR-X.21BBuffer Appendix E IR-X.21B Interface Module IR-ETH Impedance, 2-4IndicatorsIndex IP-IR IR-IP LEDRequirements, 2-1RIC-E1/R Card Excellent Good Fair Poor Very Poor Customer Response Form Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters