Manuals / Runco / Computer Equipment / Computer Monitor

Runco CW-42i manual » Wide Screen Operation with Computer Signals, Within 3 seconds, ANAMPHC mode

Models: CW-42i

1 70

Download 70 pages 841 b

Page 19

» Wide Screen Operation with Computer Signals

Aspect Ratio Controls

» Wide Screen Operation with Computer Signals

Switch to the wide screen mode to expand the 4:3 image to ﬁll the entire screen.

1.Press the ASPECT button on the remote control.

2.Within 3 seconds...

Press the ASPECT button again.

The screen size switches as follows:

STD (4:3) ANAMPHC LTR BOX

STD 4:3 mode (4:3 or SXGA 5:4)

Active

Image

Area

The picture has the same size as the normal computer image.

ANAMPHC mode

Active Image Area

The image is expanded in the horizontal direction.

LTR BOX mode

Active Image Area

When wide signals are input.

Information

■ Supported resolution

See page 61 for details on the display output of the various VESA signal standards supported by the monitor.

■When 853 (848) dot x 480 line wide VGA *signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are input.

Select an appropriate setting for RGB SELECT mode referring to the “Table of Signals Supported” on page 61. * “IBM PC/AT” and “VGA” are registered trademarks of IBM, Inc. of the United States.

NOTE:

Do not leave the displayed in 4:3 mode for an extended period. This can cause a phosphor burn-in.

17

Image 19

Runco CW-42i manual » Wide Screen Operation with Computer Signals, Within 3 seconds, STD 43 mode 43 or SXGA, ANAMPHC mode

Contents

with CW-42iOWNER’S OPERATING MANUAL Flat Panel Plasma Display MonitorPage Installation TABLE OF CONTENTSLimited Warranty How to Attach Options to the Plasma MonitorOptions » The features you’ll enjoy includeContents of the package INTRODUCTION» Warnings and Safety Precautions » PrecautionsIMPORTANT INFORMATION Recommendations to avoid or minimize phosphor burn-in » Plasma monitor cleaning procedureNOTE BURN-INS ARE NOT COVERED BY THE WARRANTY » To avoid damage and prolong operating lifeTO AVOID IMAGE BURN-IN LIMITED WARRANTYWHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTYRIGHTS, LIMITS AND EXCLUSIONS EFFECTIVE WARRANTY DATEIMPORTANT WARRANTY REGISTRATION CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICEVentilation Requirements for enclosure mounting HOW TO ATTACH OPTIONS TO THE PLASMA MONITOR6 VOLUME DOWN and UP » Front View 1 POWER2 REMOTE SENSOR WINDOW Receives the signals from the remote control 3 POWERE DVD1 / HD1 A AC INC VIDEO 1,2,3 BNC, RCA, S-Video D AUDIO1, AUDIO2, AUDIO33 CURSOR » Plasma Remote Control 1 ON/OFFVOLUME + 2 MENUDIGITAL INPUTS DVD 1 / HD1 OVERALL FUNCTIONAL DESCRIPTION» Plasma Connection Examples INSTALLATIONVCR or Laser Disc Player » Connecting Your VCR or Laser Disc Player » Connecting Your PC or Macintosh Computer» Connecting Your DVD Player Pin No » Pin Conﬁguration of the RGB3 Connector DVI Connector» Pin Assignments for 15-pin RGB analog Installation» DISPLAY To check the settings » POWER To turn the unit ON and OFF» VOLUME To adjust the sound volume » MUTE To cancel the soundLTR BOX mode When viewing videos or DVDsASPECT RATIO CONTROLS » Aspect Ratio Operations ManualANAMPHC mode » Wide Screen Operation with Computer Signals2. Within 3 seconds STD 43 mode 43 or SXGA» Menu Operations OSD ON SCREEN DISPLAY CONTROLSDefault DefaultReset ADJUSTINSTALL DefaultReset INSTALLIf “CAN NOT ADJUST” appears » PICTURE ADJUST Menu Adjusting the pictureTypes of picture modes Setting the picture mode according to the brightness of the room4. Once the adjustment is completed 3. To set to “CUSTOM1”Types of noise reduction 4. Once the setting is completedReducing noise in the picture VIDEO NRRedder Setting the KELVIN4. Once the setting is completed 5400KPerform Steps 1-3 of KELVIN, then Adjusting the Color to the Desired Level7. Once the adjustment is completed Perform the following operations4. Once the setting is completed Making the DITHER AdjustmentsChanging the GAMMA 4. Once the setting is completedSEL. ADJ. EXIT RETURN Adjusting the Colors5. Once the setting is completed Perform the following operationsRestoring the factory default settings To continue adjusting the audio ... Repeat from step» AUDIO Menu Audio setup menuOSD On Screen Display Controls Setting the allocation of the audio connectors3. To set the AUDIO INPUT1 to “VIDEO1” 4. Once the adjustment is completed» IMAGE OPTIONS Menu 2. To adjust the vertical positionTo continue making other computer image adjustments 4. Once all adjustments are completedRestoring the factory defaults settings When “COMPUTER” is offAdjusting the COMPUTER Adjusting the position of the image4. To set the DISPLAY OSD to “OFF” » INSTALL 1 Menu Setting the on-screen menu5. Once the setting is completed INSTALL Setting the BNC connectors3. To set the BNC INPUT mode to “COMP” 4. Once the setting is completed4. Once the setting is completed Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen 3. To set the RGB select mode to “AUTO”Restoring the factory default settings Setting high deﬁnition images to the suitable screen size3. To set the HD TYPE mode to “1080B” 4. Once the setting is completedINSTALL Setting the Input Skip3. To set the INPUT SKIP mode to “OFF” 4. Once the setting is completed4. Once the setting is completed Resetting to the default valuesFACTORY INSTALL » INSTALL 2 Menu Setting the Auto Off for computer images3. To turn the Auto Off function on 4. Once the setting is completedOSD On Screen Display Controls POWER / STANDBY indicatorSetting the picture to suit the movie 4. Once the setting is completedOSD On Screen Display Controls 4. Once the setting is completedLUM. SETTING Luminance Setting LUM. SETTINGORBITER FUNCTION settings Adjust the ORBITER function manuallyORBITER ORBITER settingsPerform Steps 1-2 of PDP PROTECT, then Setting the time for INVERSE6. Once the setting is completed INVERSE6. Once the setting is completed Setting the time for IMAGE SWEEP Set a time duration and the speedIMAGE SWEEP Perform Steps 1-3 of IMAGE SWEEP, then3. To adjust the “SIDEBAR ADJ” Setting the SIDEBAR ADJ. for the sides of the screenSOFTEN 4. Once the setting is completed Setting the screen size for S1/S2 video inputSetting the signal and black level for DVI signal 3.To set PLUG/PLAY mode to “STB/DVD”Perform the following operations » INSTALL 3 Menu Using the timerPerform Steps 1-2 of TIMER, then PRESENT TIMEPRESENT TIME settings PROGRAM TIMER5. Once the setting is completed Perform Steps 1-2 of TIMER, thenTo reset the program Setting the DEFAULT INPUT4. Once the setting is completed PROGRAM TIMER settingsCONTROL LOCK settings Enabling/disabling the front panel controlsTo set the CONTROL LOCK to “ON” 4. Once the setting is completedthe screen, then Enabling/disabling remote control wireless transmissionTo set the IR ENABLE to “OFF” Loop Out SettingPerform the following operations ID Number SettingTo set the ID number for the remote control 3. To set the ID NUMBER to “O2”VIDEO WALL Video Wall Setting4. Once the setting is completed Perform the following operationsDIVIDER settings DIVIDERPerform Steps 1-2 of VIDEO WALL, then POSITIONAUTO ID DISP. MODEPerform Steps 1-2 of VIDEO WALL, then P. ON DELAY settings IMAGE ADJUSTP. ON DELAY Power on delay 6. Once the setting is completedOSD On Screen Display Controls LUM SET LINKLUM SET LINK settings Perform Steps 1-2 of VIDEO WALL, thenREPEAT TIME REPEAT TIME REPEAT6. Once the setting is completed Perform Steps 1-2 of VIDEO WALL, then3. Once the setting is completed » LANGUAGE Menu Setting the language for the menus2. To select “DEUTSCH” 2. To select “3.58NTSC” » COLOR SYSTEM Menu Setting the video signal format3. Once the setting is completed SIGNAL INFO » SIGNAL INFO. MenuChecking the frequencies, polarities of input signals, and resolution 3. Once you have checked the frequencyComputer input signals supported by this system TABLE OF SIGNALS SUPPORTEDIf you are connecting a composite sync signal, use the HD terminal With digital input some signals are not accepted7 Other screen modes LTR BOX and VRTWIDE are available as well REMEDY TROUBLESHOOTINGSYMPTOM CHECKS42 diagonal DIMENSIONS3.875 41.250Power Consumption SPECIFICATIONSNative Resolution Power RequirementsPage Page Runco International 2900 Faber Street Union City, CA RUMA-010400 01-17-06Ph 510 324-7777 / Fax 510 1-800-23RUNCO