Modulation Rate-Receiver Sensitivity Typical dBm | Sagem 1500WG

Appendix D – Technical specifications

Modulation Rate-Receiver Sensitivity Typical (dBm)

802.11g - 6Mbps - (88 dBm),

802.11g - 9Mbps - (87 dBm),

802.11g - 12Mbps - (84 dBm),

802.11g - 18Mbps - (82 dBm),

802.11g - 24Mbps - (79 dBm),

802.11g - 36Mbps - (75 dBm),

802.11g - 48Mbps - (68 dBm),

802.11g - 54Mbps - (68 dBm).

SAGEM F@st™ 1500 Reference Manual - 288053220-04

Page D-6 Reproduction and communication prohibited without the written permission of E

Image 130

Sagem 1500WG manual Modulation Rate-Receiver Sensitivity Typical dBm

Contents

Reference Manual 288 053Page Contents Configuring the Sagem F@st 1500 Adsl router Appendix E Default configuration Appendix a Troubleshooting Appendix B Safety warningsAppendix D Technical specifications Appendix C Cables List of figures Front Panel Introduction Internet Access Features and BenefitsWireless and Wired LAN About the Sagem F@stTM 1500WG Adsl Router DMZ Host Support Shared IP AddressVirtual Server Security Composition of the supply Prerequisites Introduction Description and Physical installation Description and physical installation Hardware Description Front panel Status Description Rear panel ResetPower Ports / Button Description Maintenance Physical Installation Installation instructionsPower supply source Environment Desktop Installation Install the Sagem F@stTM 1500 Adsl Router Settings and Connecting ISP settingsConnect the Adsl Line Phone Line Configuration Installing a Full-Rate Connection Installing a Splitterless Connection Installing without a splitter Attach to Your Network Using Ethernet Cabling Connect the Power Adapter Powering up the Sagem F@st 1500 Adsl router Description and physical installation Configuring Client Computer Mac TCP/IP ConfigurationIP Address 192.168.2.1 Subnet Mask 255.255.255.0 Configuring your Windows computer On Windows 98 / Me Millennium Edition is similar, but not identical, to Windows TCP/IP Configuration Setting Disable Http Proxy Internet Explorer Configuring Client Computer Obtain IP Settings from Sagem F@stTM 1500 Adsl Router On the Windows desktop, click Start/Settings/Control Panel On Windows NT Configuring Client Computer TCP/IP Configuration Setting Configuring Client Computer On Windows Disable Http Proxy Obtain IP Settings from Sagem F@stTM 1500 Adsl Router Configuring Client Computer On Windows XP Disable Http Proxy Obtain IP Settings from Sagem F@st1500 Adsl Router Configuring Client Computer Configuring your Mac computer Disable Http Proxy Configuring Client Computer Configuring the Sagem F@st 1500 Adsl router Configuring the Sagem F@st 1500 Adsl router Sagem F@st Sagem F@st 1500WG Setup Wizard Advanced Setup Navigating the Management Interface Making Configuration Changes Status Additional LAN / WirelessDescription Information Setup Wizard menu PPP Setting Parameter Description Wireless ModeChannel and Ssid Essid Broadcast 3 WEP Parameter Description Access Control Time Settings System Password Settings Choose a function and click Next Configuration toolsYou will be asked to confirm your decision Firmware Upgrade Reset WAN menu ATM PVC Bridging CBR Clone MAC LAN End IP VlanParameter Description IP Address Pool Start IP Domain Name Edit Add Vlan 2 DNS Enter those addresses on this page, and click Apply Wireless Ssid Broadcast Wireless ModeChannel Access Control Security 4 WEP 5 WPA Configuring the Sagem F@st 1500 Adsl router Re-Type Password Authentication Session Idle timeoutRe-Authentication Parameter Description 802.1X NAT Address Mapping Virtual Server Special Application NAT Mapping Table Firewall Access Control Configuring the Sagem F@st 1500 Adsl router MAC Filter URL Blocking Schedule Rule Click Add Schedule Rule Intrusion Detection Intrusion Detection FeatureStateful Packet Inspection Configuring the Sagem F@st 1500 Adsl router Connection Policy DoS Criteria and Port Scan Criteria 6 DMZ Route Static Route 2 RIP Table of current Interface RIP parameter Operation ModeParameter Description General RIP Parameters Version Netmask Routing TableParameter Description Flags Interface Diffserv Forwarding Groups Parameter Description Enable or disable QoS module function10 QoS Please complete the Minimum Bandwith Allocation Traffic Mapping Parameter Description Traffic statistics Advanced Adsl Monitoring Index Interleaved Path CRC Error Parameter Operation Mode DescriptionFast Path CRC Error Loss of Signal Defect Remote Management Snmp Setting Snmp UPnP Snmp Trap Ddns Windows NT4/2000/XP Finding the MAC address of a Network CardWindows 98/ME Macintosh Configuring the Sagem F@st 1500 Adsl router Appendix a Troubleshooting Network Connection Problems Troubleshooting ChartSymptom Action LED Indicators Management Problems Symptom Action LED Indicators Wireless Problems Appendix a Troubleshooting Appendix B Safety warnings Safety levels on the Sagem F@st 1500 unit Safety warningsSafety levels on the mains adapter unit LAN Ports CE declaration of conformity SafetyRadio specific to Sagem F@st 1500WG Appendix B Safety warnings Appendix C Cables Ethernet cable SpecificationsWiring Conventions 3 RJ-45 Port Connection Pin Assignments Straight-Through WiringCrossover Wiring General Adsl Cable Cable Types and SpecificationsCable Type Connector Line Standard Telephone cable RJ11 Figure C.2 RJ-11 Connector Pin Numbers Pin Signal Name Wire Color Appendix C Cables Appendix D Technical specifications Adsl Features Mechanical Characteristics DisplaysElectrical Characteristics Input Power Management Features Soft Component FeaturesATM Features Security Features Radio Features Operating Channels Ieee 802.11b compliant RF Output Power Modulation Rate-Output Power dBmModulation Rate-Output Power dBm Operating Channels Ieee 802.11g compliant Modulation Rate-Receiver Sensitivity Typical dBm Environmental characteristics Internet Standards Appendix E Default configuration Default configuration on the local area network side Default user name and password for Http accessDefault language for Http User Interface LAN characteristics Function Mode State/Value WAN characteristics Function Mode State/Value Default configuration on the wide area network sideDefault configuration for advanced functions Advanced functions Function Mode State/Value Appendix E Default configuration Page ENetworks Division