Configuring Client Computer | Sagem 1500WG specs

3 - Configuring Client Computer

3)Type “IPCONFIG /RENEW” and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your SAGEM F@stTM 1500 ADSL Router is functioning. Type “EXIT” and press the ENTER key to close the Command Prompt window.

Your computer is now configured to connect to the SAGEM F@stTM 1500 ADSL Router.

SAGEM F@st™ 1500 Reference Manual - 288053220-04 Reproduction and communication prohibited without the written permission of E Page 3-19

Image 43

Sagem 1500WG manual Configuring Client Computer

Contents

288 053 Reference ManualPage Contents Configuring the Sagem F@st 1500 Adsl router Appendix C Cables Appendix a Troubleshooting Appendix B Safety warningsAppendix D Technical specifications Appendix E Default configuration Front Panel List of figures Introduction About the Sagem F@stTM 1500WG Adsl Router Features and BenefitsWireless and Wired LAN Internet Access Security Shared IP AddressVirtual Server DMZ Host Support Composition of the supply Prerequisites Introduction Description and Physical installation Hardware Description Description and physical installation Status Description Front panel Ports / Button Description ResetPower Rear panel Environment Physical Installation Installation instructionsPower supply source Maintenance Desktop Installation Install the Sagem F@stTM 1500 Adsl Router Settings and Connecting ISP settingsConnect the Adsl Line Installing a Full-Rate Connection Phone Line Configuration Installing without a splitter Installing a Splitterless Connection Connect the Power Adapter Attach to Your Network Using Ethernet Cabling Powering up the Sagem F@st 1500 Adsl router Description and physical installation Configuring Client Computer Mac TCP/IP ConfigurationIP Address 192.168.2.1 Subnet Mask 255.255.255.0 Millennium Edition is similar, but not identical, to Windows Configuring your Windows computer On Windows 98 / Me TCP/IP Configuration Setting Internet Explorer Disable Http Proxy Configuring Client Computer Obtain IP Settings from Sagem F@stTM 1500 Adsl Router On Windows NT On the Windows desktop, click Start/Settings/Control Panel Configuring Client Computer TCP/IP Configuration Setting Configuring Client Computer On Windows Disable Http Proxy Obtain IP Settings from Sagem F@stTM 1500 Adsl Router Configuring Client Computer On Windows XP Disable Http Proxy Obtain IP Settings from Sagem F@st1500 Adsl Router Configuring Client Computer Configuring your Mac computer Disable Http Proxy Configuring Client Computer Configuring the Sagem F@st 1500 Adsl router Sagem F@st Configuring the Sagem F@st 1500 Adsl router Sagem F@st 1500WG Navigating the Management Interface Setup Wizard Advanced Setup Making Configuration Changes Status Information LAN / WirelessDescription Additional PPP Setting Setup Wizard menu Essid Broadcast Wireless ModeChannel and Ssid Parameter Description Parameter Description 3 WEP Access Control System Time Settings Password Settings Choose a function and click Next Configuration toolsYou will be asked to confirm your decision Reset Firmware Upgrade WAN menu Bridging ATM PVC CBR Clone MAC LAN Domain Name VlanParameter Description IP Address Pool Start IP End IP Add Vlan Edit Enter those addresses on this page, and click Apply 2 DNS Wireless Ssid Broadcast Wireless ModeChannel Access Control Security 4 WEP 5 WPA Configuring the Sagem F@st 1500 Adsl router Parameter Description 802.1X Authentication Session Idle timeoutRe-Authentication Re-Type Password NAT Address Mapping Virtual Server Special Application NAT Mapping Table Firewall Access Control Configuring the Sagem F@st 1500 Adsl router MAC Filter URL Blocking Click Add Schedule Rule Schedule Rule Intrusion Detection Intrusion Detection FeatureStateful Packet Inspection Configuring the Sagem F@st 1500 Adsl router Connection Policy DoS Criteria and Port Scan Criteria 6 DMZ Static Route Route 2 RIP Version Operation ModeParameter Description General RIP Parameters Table of current Interface RIP parameter Interface Routing TableParameter Description Flags Netmask Please complete the Minimum Bandwith Allocation Parameter Description Enable or disable QoS module function10 QoS Diffserv Forwarding Groups Traffic Mapping Parameter Description Traffic statistics Adsl Advanced Monitoring Index Loss of Signal Defect Parameter Operation Mode DescriptionFast Path CRC Error Interleaved Path CRC Error Remote Management Snmp Snmp Setting Snmp Trap UPnP Ddns Macintosh Finding the MAC address of a Network CardWindows 98/ME Windows NT4/2000/XP Configuring the Sagem F@st 1500 Adsl router Appendix a Troubleshooting Management Problems Troubleshooting ChartSymptom Action LED Indicators Network Connection Problems Symptom Action LED Indicators Wireless Problems Appendix a Troubleshooting Appendix B Safety warnings LAN Ports Safety warningsSafety levels on the mains adapter unit Safety levels on the Sagem F@st 1500 unit CE declaration of conformity SafetyRadio specific to Sagem F@st 1500WG Appendix B Safety warnings Appendix C Cables 3 RJ-45 Port Connection SpecificationsWiring Conventions Ethernet cable General Straight-Through WiringCrossover Wiring Pin Assignments Line Standard Telephone cable RJ11 Cable Types and SpecificationsCable Type Connector Adsl Cable Pin Signal Name Wire Color Figure C.2 RJ-11 Connector Pin Numbers Appendix C Cables Appendix D Technical specifications Input Power Mechanical Characteristics DisplaysElectrical Characteristics Adsl Features Security Features Soft Component FeaturesATM Features Management Features Radio Features Operating Channels Ieee 802.11g compliant RF Output Power Modulation Rate-Output Power dBmModulation Rate-Output Power dBm Operating Channels Ieee 802.11b compliant Modulation Rate-Receiver Sensitivity Typical dBm Environmental characteristics Internet Standards Appendix E Default configuration LAN characteristics Function Mode State/Value Default user name and password for Http accessDefault language for Http User Interface Default configuration on the local area network side Advanced functions Function Mode State/Value Default configuration on the wide area network sideDefault configuration for advanced functions WAN characteristics Function Mode State/Value Appendix E Default configuration Page ENetworks Division