Parameter Description General RIP Parameters, Code | Sagem 1500WG

4 - Configuring the SAGEM F@st™ 1500 ADSL router

Parameter Description

General RIP Parameters

RIP mode Globally enables or disables RIP.

Auto summary If Auto summary is disabled, then RIP packets will include sub- network information from all subnetworks connected to the router. If enabled, this sub-network information will be summarized to one piece of information covering all subnetworks.

Table of current Interface RIP parameter

Interface The WAN interface to be configured.

Operation Mode	• Disable: RIP disabled on this interface.
	• Enable: RIP enabled on this interface.
	• Silent: Listens for route broadcasts and updates its route table.
	It does not participate in sending route broadcasts.
Version	Sets the RIP (Routing Information Protocol) version to use on
	this interface.
Poison Reverse	A method for preventing loops that would cause endless
	retransmission of data traffic.

Authentication	• None: No authentication.
Required	• Password: A password authentication key is included in the
	packet. If this does not match what is expected, the packet will
	be discarded. This method provides very little security as it is
	possible to learn the authentication key by watching RIP
	packets.
	• MD5: An algorithm that is used to verify data integrity through
	the creation of a 128-bit message digest from data input (which
	may
	be a message of any length) that is claimed to be as unique to
	that specific data as a fingerprint is to a specific individual.

Authentication	Password or MD5 Authentication key.
Code

RIP sends routing-update messages at regular intervals and when the network topology changes. When a router receives a routing update that includes changes to an entry, it updates its routing table to reflect the new route. RIP routers maintain only the best route to a destination. After updating its routing table, the router immediately begins transmitting routing updates to inform other network routers of the change.

SAGEM F@st™ 1500 Reference Manual - 288053220-04

Page 4-50 Reproduction and communication prohibited without the written permission of E

Image 96

Sagem 1500WG Parameter Description General RIP Parameters, Table of current Interface RIP parameter, Operation Mode, Code

Contents

Reference Manual 288 053Page Contents Configuring the Sagem F@st 1500 Adsl router Appendix a Troubleshooting Appendix B Safety warnings Appendix D Technical specificationsAppendix E Default configuration Appendix C Cables List of figures Front Panel Introduction Features and Benefits Wireless and Wired LANInternet Access About the Sagem F@stTM 1500WG Adsl Router Shared IP Address Virtual ServerDMZ Host Support Security Composition of the supply Prerequisites Introduction Description and Physical installation Description and physical installation Hardware Description Front panel Status Description Reset PowerRear panel Ports / Button Description Physical Installation Installation instructions Power supply sourceMaintenance Environment Desktop Installation Settings and Connecting ISP settings Install the Sagem F@stTM 1500 Adsl RouterConnect the Adsl Line Phone Line Configuration Installing a Full-Rate Connection Installing a Splitterless Connection Installing without a splitter Attach to Your Network Using Ethernet Cabling Connect the Power Adapter Powering up the Sagem F@st 1500 Adsl router Description and physical installation Configuring Client Computer TCP/IP Configuration MacIP Address 192.168.2.1 Subnet Mask 255.255.255.0 Configuring your Windows computer On Windows 98 / Me Millennium Edition is similar, but not identical, to Windows TCP/IP Configuration Setting Disable Http Proxy Internet Explorer Configuring Client Computer Obtain IP Settings from Sagem F@stTM 1500 Adsl Router On the Windows desktop, click Start/Settings/Control Panel On Windows NT Configuring Client Computer TCP/IP Configuration Setting Configuring Client Computer On Windows Disable Http Proxy Obtain IP Settings from Sagem F@stTM 1500 Adsl Router Configuring Client Computer On Windows XP Disable Http Proxy Obtain IP Settings from Sagem F@st1500 Adsl Router Configuring Client Computer Configuring your Mac computer Disable Http Proxy Configuring Client Computer Configuring the Sagem F@st 1500 Adsl router Configuring the Sagem F@st 1500 Adsl router Sagem F@st Sagem F@st 1500WG Setup Wizard Advanced Setup Navigating the Management Interface Making Configuration Changes Status LAN / Wireless DescriptionAdditional Information Setup Wizard menu PPP Setting Wireless Mode Channel and SsidParameter Description Essid Broadcast 3 WEP Parameter Description Access Control Time Settings System Password Settings Configuration tools Choose a function and click NextYou will be asked to confirm your decision Firmware Upgrade Reset WAN menu ATM PVC Bridging CBR Clone MAC LAN Vlan Parameter Description IP Address Pool Start IPEnd IP Domain Name Edit Add Vlan 2 DNS Enter those addresses on this page, and click Apply Wireless Wireless Mode Ssid BroadcastChannel Access Control Security 4 WEP 5 WPA Configuring the Sagem F@st 1500 Adsl router Authentication Session Idle timeout Re-AuthenticationRe-Type Password Parameter Description 802.1X NAT Address Mapping Virtual Server Special Application NAT Mapping Table Firewall Access Control Configuring the Sagem F@st 1500 Adsl router MAC Filter URL Blocking Schedule Rule Click Add Schedule Rule Intrusion Detection Feature Intrusion DetectionStateful Packet Inspection Configuring the Sagem F@st 1500 Adsl router Connection Policy DoS Criteria and Port Scan Criteria 6 DMZ Route Static Route 2 RIP Operation Mode Parameter Description General RIP ParametersTable of current Interface RIP parameter Version Routing Table Parameter Description FlagsNetmask Interface Parameter Description Enable or disable QoS module function 10 QoSDiffserv Forwarding Groups Please complete the Minimum Bandwith Allocation Traffic Mapping Parameter Description Traffic statistics Advanced Adsl Monitoring Index Parameter Operation Mode Description Fast Path CRC ErrorInterleaved Path CRC Error Loss of Signal Defect Remote Management Snmp Setting Snmp UPnP Snmp Trap Ddns Finding the MAC address of a Network Card Windows 98/MEWindows NT4/2000/XP Macintosh Configuring the Sagem F@st 1500 Adsl router Appendix a Troubleshooting Troubleshooting Chart Symptom Action LED IndicatorsNetwork Connection Problems Management Problems Symptom Action LED Indicators Wireless Problems Appendix a Troubleshooting Appendix B Safety warnings Safety warnings Safety levels on the mains adapter unitSafety levels on the Sagem F@st 1500 unit LAN Ports Safety CE declaration of conformityRadio specific to Sagem F@st 1500WG Appendix B Safety warnings Appendix C Cables Specifications Wiring ConventionsEthernet cable 3 RJ-45 Port Connection Straight-Through Wiring Crossover WiringPin Assignments General Cable Types and Specifications Cable Type ConnectorAdsl Cable Line Standard Telephone cable RJ11 Figure C.2 RJ-11 Connector Pin Numbers Pin Signal Name Wire Color Appendix C Cables Appendix D Technical specifications Mechanical Characteristics Displays Electrical CharacteristicsAdsl Features Input Power Soft Component Features ATM FeaturesManagement Features Security Features Radio Features RF Output Power Modulation Rate-Output Power dBm Modulation Rate-Output Power dBmOperating Channels Ieee 802.11b compliant Operating Channels Ieee 802.11g compliant Modulation Rate-Receiver Sensitivity Typical dBm Environmental characteristics Internet Standards Appendix E Default configuration Default user name and password for Http access Default language for Http User InterfaceDefault configuration on the local area network side LAN characteristics Function Mode State/Value Default configuration on the wide area network side Default configuration for advanced functionsWAN characteristics Function Mode State/Value Advanced functions Function Mode State/Value Appendix E Default configuration Page ENetworks Division