Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual B Remove the toner cartridge for the color you want to replace

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 12

Image 12

Replacing Consumables and Maintenance Kit

B Remove the toner cartridge for the color you want to replace.

Note

❒ The black toner cartridge con-

A Unhook the green hook on the toner cartridge with one hand.

tains more than the other toner

cartridges.

D Shake the toner cartridge back and forth 5-6 times.

ZDJT999J

B Holding the toner cartridge with the other hand, pull out the cartridge up slowly.

ZDJT201J

Important

❒Do not shake the removed toner cartridge. The remain- ing toner might scatter.

C Take out a new toner cartridge from the box.

ZDJT202J

ZDJT203J

E Holding the toner cartridge with the metal contact area in front, at- tach in the direction of the arrow.

ZDJT004J

Important

❒Do not touch the metal contact point with your fingers.

Page 12

Image 12

Savin SLP38C manual B Remove the toner cartridge for the color you want to replace

Contents

Maintenance Guide For safety, please follow the instructions in this manualOperating Instructions Introduction Trademarks Safety Information Safety During OperationR WARNING R CAUTION ENERGY STAR Program Low-power Mode Energy Saver modeSpecifications How to Read This Manual SymbolsPreparation LimitationTABLE OF CONTENTS 1.Replacing Consumables and Maintenance Kit2.Clearing and Adjusting the Printer 3.Appendix1. Replacing Consumables and Maintenance Kit Detaching the SR770 2 Tray FinisherOpening and Closing the Duplex Reversal Unit A Push up the lock release button and keep it in placeB Lower the Duplex Reversal Unit slowly until it stops Replacing the Toner Cartridge Add Toner XXXAdd Toner XXX/XXX B Remove the toner cartridge for the color you want to replace Loading Toner G Close the upper right coverReplacing the Fuser Oil Unit Replace Fuser Oil Unit TypeGReference See P.1 “Detaching the SR770 2 Tray Finisher”H Put the removed Fusing Unit in a stable and level place P If the Duplex Unit is installed, close the Duplex Reversal Unit ReferenceSee P.2 “Opening and Closing the Duplex Reversal Unit” ReferenceR Plug in the power cable and turn on the power switch If you dispose of the used tonercartridges by yourself, dispose of them according to local regu- lationsReplacing the Photoconductor Unit Replace Black PCU Type FReplace Color PCU Type A F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replacing the Development Unit Replace Black Dev. UnitTypeDReplace Color Dev. UnitTypeB Page Page Please Wait Replacing the Fusing Unit Replace Fusing Unit Type CReference See P.1 “Detaching the SR770 2 Tray Finisher”I Remove the Fuser Oil Unit in the direction of the arrow Press # for Fuser Adjust Initializing Please WaitPlease Wait CalibratingSet Sheet in Bypass, then # A B C D E F G H 0 0 0 0 0 0 0 ReadyInvalid Value Press # ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust”Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replacing the Waste Toner Bottle Replace Waste Toner Type EJ Plug in the power cable and turn on the power switch Replacing Consumables and Maintenance KitH Push it in until it stops ZDJH230JReplacing the Paper Feed Rollers Paper Feed Roller A Paper Feed Roller B Paper Feed Roller CTwo Stoppers ZERH040E ZERH050EZERH060E ZERH070EK Slide all trays back into the print- er slowly until it stops Replacing the Paper Feed RollersZERH090E Replacing Consumables and Maintenance Kit 2. Clearing and Adjusting the Printer Cautions to Take When CleaningWhen removing misfed paper, do not touch the fusing section be cause it could be very hotCleaning the Registration Roller Clean the roller when replacing the black Development UnitThe registration roller is set shown in the illustration Cleaning the DustProof Glass Adjusting the Color Registration Auto AdjustMenu Maintenance Maintenance Color RegistFuser Adjust Completed Color Regist Auto AdjustMenu Maintenance Maintenance Color RegistColor Regist Fuser Adjust Cannot Adjust See User’s GuideFuser Adjust At Unit Replace Invalid Value Cannot AdjustFuser Adjust Custom Adjust Custom Adjust Plain 600dpiMenu Maintenance Maintenance Color RegistManual Adjust Select Action 0 Exit Select Action 1 Re-adjustSelect Action +1 Re-adjust Press # for Test Print BypassColor Regist Manual Adjust Manual Adjust Print ResultAdjustment A -7.0 +7.0 +0 Adjustment A -7.0 +7.0 +2Test Sheet Samples Fuser Adjust SheetClearing and Adjusting the Printer ColorRegistSheetFuser Adjust Sheet Adjusting the Color RegistrationAdjusting the Image Density Maintenance Image DensityImage Density Black BlackAdjusting the Registration of the Trays Maintenance RegistrationRegistration Adjustment Registration Prt. Test SheetAdjustment Vert. Tray Vert. Tray 3 -4.0 +4.0C Press U or T to display the tray to adjust, and then press Ready3. Appendix Removing Misfed Paper in the Duplex Feed UnitH Close the Duplex Feed Unit L Plug in the power cable and turn on the power switch Removing Misfed Paper in the Duplex Feed UnitZDJH041J When the Front Cover Does Not Close Close Front CoverF Plug in the power cable and turn on the power switch When the Front Cover Does Not CloseZDJH041J Consumables Toner cartridgeStaple Cartridge Other consumables NameConsumables Average printable number ofPaper Recommendations Loading PaperStoring Paper Types of Paper and Other MediaThick Paper OHP transparenciesPaper Recommendations Envelopes Paper not supported by this printerPrintable Area INDEX Copyright UE USA G060-6920