Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual Cleaning the DustProof Glass

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 41

Image 41

Cleaning the DustProof Glass

The dustproof glass may require cleaning if white lines appear on the print side of the document.

A Turn off the power switch and unplug the power cable.

B Open the front cover and remove the cleaning brush.

ZDJP705J

There are four holes for cleaning the dustproof glass.

ZDJP706J

C Slide the cleaning brush in and out slowly 8 to 10 times to clean all four areas.

ZDJP707J

Important

❒Do not insert the brush roughly, or the printer might be dam- aged.

D Return the cleaning brush to its original position.

E Plug in the power cable and turn on the power switch.

Page 41

Image 41

Savin SLP38C manual Cleaning the DustProof Glass

Contents

Operating Instructions Maintenance GuideFor safety, please follow the instructions in this manual Introduction Trademarks R WARNING Safety InformationSafety During Operation R CAUTION Specifications ENERGY STAR ProgramLow-power Mode Energy Saver mode Symbols How to Read This ManualPreparation Limitation1.Replacing Consumables and Maintenance Kit TABLE OF CONTENTS2.Clearing and Adjusting the Printer 3.AppendixDetaching the SR770 2 Tray Finisher 1. Replacing Consumables and Maintenance KitB Lower the Duplex Reversal Unit slowly until it stops Opening and Closing the Duplex Reversal UnitA Push up the lock release button and keep it in place Add Toner XXX/XXX Replacing the Toner CartridgeAdd Toner XXX B Remove the toner cartridge for the color you want to replace G Close the upper right cover Loading TonerReplace Fuser Oil Unit TypeG Replacing the Fuser Oil UnitReference See P.1 “Detaching the SR770 2 Tray Finisher”H Put the removed Fusing Unit in a stable and level place Reference P If the Duplex Unit is installed, close the Duplex Reversal UnitSee P.2 “Opening and Closing the Duplex Reversal Unit” ReferenceIf you dispose of the used toner R Plug in the power cable and turn on the power switchcartridges by yourself, dispose of them according to local regu- lationsReplace Color PCU Type A Replacing the Photoconductor UnitReplace Black PCU Type F F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replace Color Dev. UnitTypeB Replacing the Development UnitReplace Black Dev. UnitTypeD Page Page Please Wait Replace Fusing Unit Type C Replacing the Fusing UnitReference See P.1 “Detaching the SR770 2 Tray Finisher”I Remove the Fuser Oil Unit in the direction of the arrow Initializing Please Wait Press # for Fuser AdjustPlease Wait CalibratingSet Sheet in Bypass, then # Ready A B C D E F G H 0 0 0 0 0 0 0Invalid Value Press # ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust”Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replace Waste Toner Type E Replacing the Waste Toner BottleReplacing Consumables and Maintenance Kit J Plug in the power cable and turn on the power switchH Push it in until it stops ZDJH230JTwo Stoppers Replacing the Paper Feed RollersPaper Feed Roller A Paper Feed Roller B Paper Feed Roller C ZERH050E ZERH040EZERH060E ZERH070EZERH090E K Slide all trays back into the print- er slowly until it stopsReplacing the Paper Feed Rollers Replacing Consumables and Maintenance Kit Cautions to Take When Cleaning 2. Clearing and Adjusting the PrinterWhen removing misfed paper, do not touch the fusing section be cause it could be very hotThe registration roller is set shown in the illustration Cleaning the Registration RollerClean the roller when replacing the black Development Unit Cleaning the DustProof Glass Auto Adjust Adjusting the Color RegistrationMenu Maintenance Maintenance Color RegistCompleted Color Regist Auto Adjust Fuser AdjustMenu Maintenance Maintenance Color RegistCannot Adjust See User’s Guide Color Regist Fuser AdjustFuser Adjust At Unit Replace Invalid Value Cannot AdjustCustom Adjust Plain 600dpi Fuser Adjust Custom AdjustMenu Maintenance Maintenance Color RegistSelect Action 0 Exit Select Action 1 Re-adjust Manual AdjustSelect Action +1 Re-adjust Press # for Test Print BypassManual Adjust Print Result Color Regist Manual AdjustAdjustment A -7.0 +7.0 +0 Adjustment A -7.0 +7.0 +2Fuser Adjust Sheet Test Sheet SamplesClearing and Adjusting the Printer ColorRegistSheetAdjusting the Color Registration Fuser Adjust SheetMaintenance Image Density Adjusting the Image DensityImage Density Black BlackMaintenance Registration Adjusting the Registration of the TraysRegistration Adjustment Registration Prt. Test SheetVert. Tray 3 -4.0 +4.0 Adjustment Vert. TrayC Press U or T to display the tray to adjust, and then press ReadyRemoving Misfed Paper in the Duplex Feed Unit 3. AppendixH Close the Duplex Feed Unit ZDJH041J L Plug in the power cable and turn on the power switchRemoving Misfed Paper in the Duplex Feed Unit Close Front Cover When the Front Cover Does Not CloseZDJH041J F Plug in the power cable and turn on the power switchWhen the Front Cover Does Not Close Staple Cartridge ConsumablesToner cartridge Name Other consumablesConsumables Average printable number ofLoading Paper Paper RecommendationsStoring Paper Types of Paper and Other MediaPaper Recommendations Thick PaperOHP transparencies Paper not supported by this printer EnvelopesPrintable Area INDEX Copyright UE USA G060-6920