Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual Printable Area

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 63

Image 63

Paper Recommendations

Printable Area

The following shows the printable area for this printer. Be sure to set the print margins correctly by the application.

4.2mm (0.166 inch)	Feed Direction
4.2mm (0.166 inch)	4.2mm (0.166 inch)
4.2mm (0.166 inch)

4.2mm (0.166 inch)

A: printable area

Note

❒The printable area may vary depending on the paper size, printer language and printer driver settings.

Page 63

Image 63

Contents

Maintenance Guide For safety, please follow the instructions in this manualOperating Instructions Introduction Trademarks Safety Information Safety During OperationR WARNING R CAUTION ENERGY STAR Program Low-power Mode Energy Saver modeSpecifications Limitation How to Read This ManualSymbols Preparation3.Appendix TABLE OF CONTENTS1.Replacing Consumables and Maintenance Kit 2.Clearing and Adjusting the PrinterDetaching the SR770 2 Tray Finisher 1. Replacing Consumables and Maintenance KitOpening and Closing the Duplex Reversal Unit A Push up the lock release button and keep it in placeB Lower the Duplex Reversal Unit slowly until it stops Replacing the Toner Cartridge Add Toner XXXAdd Toner XXX/XXX B Remove the toner cartridge for the color you want to replace G Close the upper right cover Loading TonerSee P.1 “Detaching the SR770 2 Tray Finisher” Replacing the Fuser Oil UnitReplace Fuser Oil Unit TypeG ReferenceH Put the removed Fusing Unit in a stable and level place Reference P If the Duplex Unit is installed, close the Duplex Reversal UnitReference See P.2 “Opening and Closing the Duplex Reversal Unit”of them according to local regu- lations R Plug in the power cable and turn on the power switchIf you dispose of the used toner cartridges by yourself, disposeReplacing the Photoconductor Unit Replace Black PCU Type FReplace Color PCU Type A F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replacing the Development Unit Replace Black Dev. UnitTypeDReplace Color Dev. UnitTypeB Page Page Please Wait See P.1 “Detaching the SR770 2 Tray Finisher” Replacing the Fusing UnitReplace Fusing Unit Type C ReferenceI Remove the Fuser Oil Unit in the direction of the arrow Calibrating Press # for Fuser AdjustInitializing Please Wait Please WaitSet Sheet in Bypass, then # ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust” A B C D E F G H 0 0 0 0 0 0 0Ready Invalid Value Press #Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replace Waste Toner Type E Replacing the Waste Toner BottleZDJH230J J Plug in the power cable and turn on the power switchReplacing Consumables and Maintenance Kit H Push it in until it stopsReplacing the Paper Feed Rollers Paper Feed Roller A Paper Feed Roller B Paper Feed Roller CTwo Stoppers ZERH070E ZERH040EZERH050E ZERH060EK Slide all trays back into the print- er slowly until it stops Replacing the Paper Feed RollersZERH090E Replacing Consumables and Maintenance Kit cause it could be very hot 2. Clearing and Adjusting the PrinterCautions to Take When Cleaning When removing misfed paper, do not touch the fusing section beCleaning the Registration Roller Clean the roller when replacing the black Development UnitThe registration roller is set shown in the illustration Cleaning the DustProof Glass Maintenance Color Regist Adjusting the Color RegistrationAuto Adjust Menu MaintenanceMaintenance Color Regist Fuser AdjustCompleted Color Regist Auto Adjust Menu MaintenanceInvalid Value Cannot Adjust Color Regist Fuser AdjustCannot Adjust See User’s Guide Fuser Adjust At Unit ReplaceMaintenance Color Regist Fuser Adjust Custom AdjustCustom Adjust Plain 600dpi Menu MaintenancePress # for Test Print Bypass Manual AdjustSelect Action 0 Exit Select Action 1 Re-adjust Select Action +1 Re-adjustAdjustment A -7.0 +7.0 +2 Color Regist Manual AdjustManual Adjust Print Result Adjustment A -7.0 +7.0 +0ColorRegistSheet Test Sheet SamplesFuser Adjust Sheet Clearing and Adjusting the PrinterAdjusting the Color Registration Fuser Adjust SheetBlack Adjusting the Image DensityMaintenance Image Density Image Density BlackRegistration Prt. Test Sheet Adjusting the Registration of the TraysMaintenance Registration Registration AdjustmentReady Adjustment Vert. TrayVert. Tray 3 -4.0 +4.0 C Press U or T to display the tray to adjust, and then pressRemoving Misfed Paper in the Duplex Feed Unit 3. AppendixH Close the Duplex Feed Unit L Plug in the power cable and turn on the power switch Removing Misfed Paper in the Duplex Feed UnitZDJH041J Close Front Cover When the Front Cover Does Not CloseF Plug in the power cable and turn on the power switch When the Front Cover Does Not CloseZDJH041J Consumables Toner cartridgeStaple Cartridge Average printable number of Other consumablesName ConsumablesTypes of Paper and Other Media Paper RecommendationsLoading Paper Storing PaperThick Paper OHP transparenciesPaper Recommendations Paper not supported by this printer EnvelopesPrintable Area INDEX Copyright UE USA G060-6920