Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual Replacing the Waste Toner Bottle, Replace Waste Toner Type E

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 33

Image 33

Replacing the Waste Toner Bottle

If "Replace Waste Toner (Type E)" ap- pears on the panel display, replace the waste toner bottle.

Replace Waste

Toner (Type E)

A Turn off the power switch and unplug the power cable.

B Open the front cover slowly by pulling down from the two areas on the left and right.

ZDJH007J

C Take out a new waste toner bottle from the bag.

D Remove the used waste toner bot-	1
tle slowly from inside the printer.

ZDJH802J

Important

❒Be sure to remove the waste toner bottle in a level manner.

E Remove the lid (A), and then put it on the position shown in the il- lustration (B).

ZDJH229J

F Put the used waste toner bottle into the bag that contained the new waste toner bottle, and then seal the bag.

ZDJH228J

Important

❒Be sure to handle the bottle carefully so the waste toner does not spill.

Page 33

Image 33

Savin SLP38C manual Replacing the Waste Toner Bottle, Replace Waste Toner Type E

Contents

Maintenance Guide For safety, please follow the instructions in this manualOperating Instructions Introduction Trademarks Safety Information Safety During OperationR WARNING R CAUTION ENERGY STAR Program Low-power Mode Energy Saver modeSpecifications Symbols How to Read This ManualPreparation Limitation1.Replacing Consumables and Maintenance Kit TABLE OF CONTENTS2.Clearing and Adjusting the Printer 3.AppendixDetaching the SR770 2 Tray Finisher 1. Replacing Consumables and Maintenance KitOpening and Closing the Duplex Reversal Unit A Push up the lock release button and keep it in placeB Lower the Duplex Reversal Unit slowly until it stops Replacing the Toner Cartridge Add Toner XXXAdd Toner XXX/XXX B Remove the toner cartridge for the color you want to replace G Close the upper right cover Loading TonerReplace Fuser Oil Unit TypeG Replacing the Fuser Oil UnitReference See P.1 “Detaching the SR770 2 Tray Finisher”H Put the removed Fusing Unit in a stable and level place Reference P If the Duplex Unit is installed, close the Duplex Reversal UnitSee P.2 “Opening and Closing the Duplex Reversal Unit” ReferenceIf you dispose of the used toner R Plug in the power cable and turn on the power switchcartridges by yourself, dispose of them according to local regu- lationsReplacing the Photoconductor Unit Replace Black PCU Type FReplace Color PCU Type A F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replacing the Development Unit Replace Black Dev. UnitTypeDReplace Color Dev. UnitTypeB Page Page Please Wait Replace Fusing Unit Type C Replacing the Fusing UnitReference See P.1 “Detaching the SR770 2 Tray Finisher”I Remove the Fuser Oil Unit in the direction of the arrow Initializing Please Wait Press # for Fuser AdjustPlease Wait CalibratingSet Sheet in Bypass, then # Ready A B C D E F G H 0 0 0 0 0 0 0Invalid Value Press # ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust”Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replace Waste Toner Type E Replacing the Waste Toner BottleReplacing Consumables and Maintenance Kit J Plug in the power cable and turn on the power switchH Push it in until it stops ZDJH230JReplacing the Paper Feed Rollers Paper Feed Roller A Paper Feed Roller B Paper Feed Roller CTwo Stoppers ZERH050E ZERH040EZERH060E ZERH070EK Slide all trays back into the print- er slowly until it stops Replacing the Paper Feed RollersZERH090E Replacing Consumables and Maintenance Kit Cautions to Take When Cleaning 2. Clearing and Adjusting the PrinterWhen removing misfed paper, do not touch the fusing section be cause it could be very hotCleaning the Registration Roller Clean the roller when replacing the black Development UnitThe registration roller is set shown in the illustration Cleaning the DustProof Glass Auto Adjust Adjusting the Color RegistrationMenu Maintenance Maintenance Color RegistCompleted Color Regist Auto Adjust Fuser AdjustMenu Maintenance Maintenance Color RegistCannot Adjust See User’s Guide Color Regist Fuser AdjustFuser Adjust At Unit Replace Invalid Value Cannot AdjustCustom Adjust Plain 600dpi Fuser Adjust Custom AdjustMenu Maintenance Maintenance Color RegistSelect Action 0 Exit Select Action 1 Re-adjust Manual AdjustSelect Action +1 Re-adjust Press # for Test Print BypassManual Adjust Print Result Color Regist Manual AdjustAdjustment A -7.0 +7.0 +0 Adjustment A -7.0 +7.0 +2Fuser Adjust Sheet Test Sheet SamplesClearing and Adjusting the Printer ColorRegistSheetAdjusting the Color Registration Fuser Adjust SheetMaintenance Image Density Adjusting the Image DensityImage Density Black BlackMaintenance Registration Adjusting the Registration of the TraysRegistration Adjustment Registration Prt. Test SheetVert. Tray 3 -4.0 +4.0 Adjustment Vert. TrayC Press U or T to display the tray to adjust, and then press ReadyRemoving Misfed Paper in the Duplex Feed Unit 3. AppendixH Close the Duplex Feed Unit L Plug in the power cable and turn on the power switch Removing Misfed Paper in the Duplex Feed UnitZDJH041J Close Front Cover When the Front Cover Does Not CloseF Plug in the power cable and turn on the power switch When the Front Cover Does Not CloseZDJH041J Consumables Toner cartridgeStaple Cartridge Name Other consumablesConsumables Average printable number ofLoading Paper Paper RecommendationsStoring Paper Types of Paper and Other MediaThick Paper OHP transparenciesPaper Recommendations Paper not supported by this printer EnvelopesPrintable Area INDEX Copyright UE USA G060-6920