Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual Replacing the Paper Feed Rollers, Two Stoppers

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 35

Replacing the Paper Feed Rollers

Replacing the Paper Feed Rollers

Replacing the Paper Feed Rollers

RCAUTION:

•The inside of the machine be- comes very hot. Do not touch the parts with a label indicating a "hot surface". Touching a "hot surface" could result in a burn.

Note

❒The following illustrations are the an examples of replacing the paper feed rollers of Tray 1. The same procedure is followed with the other trays.

A Check the contents of the box.

❖Paper Feed Roller A

❖Paper Feed Roller B

❖Paper Feed Roller C

❖Two Stoppers

B Turn off the power switch and unplug the power cable and inter- face cable.

Important

❒If you replace the paper feed rollers of the optional 2000- sheet Large Capacity Tray, re- move all paper from the tray.

C Pull out all trays slowly while lift-	1
ing it up a little.

ZERH010E

Note

❒If you replace the paper feed rollers of the optional Paper Feed Unit, or 2000-sheet Large Capacity Tray, pull out all the paper trays from each unit.

D Confirm the position of the paper feed rollers.

ZERH020E

Confirm the positions and names of each roller.

ZERH030E	27

Image 35

Savin SLP38C Replacing the Paper Feed Rollers, Paper Feed Roller A Paper Feed Roller B Paper Feed Roller C, Two Stoppers

Contents

Operating Instructions Maintenance GuideFor safety, please follow the instructions in this manual Introduction Trademarks R WARNING Safety InformationSafety During Operation R CAUTION Specifications ENERGY STAR ProgramLow-power Mode Energy Saver mode Limitation How to Read This ManualSymbols Preparation3.Appendix TABLE OF CONTENTS1.Replacing Consumables and Maintenance Kit 2.Clearing and Adjusting the PrinterDetaching the SR770 2 Tray Finisher 1. Replacing Consumables and Maintenance KitB Lower the Duplex Reversal Unit slowly until it stops Opening and Closing the Duplex Reversal UnitA Push up the lock release button and keep it in place Add Toner XXX/XXX Replacing the Toner CartridgeAdd Toner XXX B Remove the toner cartridge for the color you want to replace G Close the upper right cover Loading TonerSee P.1 “Detaching the SR770 2 Tray Finisher” Replacing the Fuser Oil UnitReplace Fuser Oil Unit TypeG ReferenceH Put the removed Fusing Unit in a stable and level place Reference P If the Duplex Unit is installed, close the Duplex Reversal UnitReference See P.2 “Opening and Closing the Duplex Reversal Unit”of them according to local regu- lations R Plug in the power cable and turn on the power switchIf you dispose of the used toner cartridges by yourself, disposeReplace Color PCU Type A Replacing the Photoconductor UnitReplace Black PCU Type F F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replace Color Dev. UnitTypeB Replacing the Development UnitReplace Black Dev. UnitTypeD Page Page Please Wait See P.1 “Detaching the SR770 2 Tray Finisher” Replacing the Fusing UnitReplace Fusing Unit Type C ReferenceI Remove the Fuser Oil Unit in the direction of the arrow Calibrating Press # for Fuser AdjustInitializing Please Wait Please WaitSet Sheet in Bypass, then # ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust” A B C D E F G H 0 0 0 0 0 0 0Ready Invalid Value Press #Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replace Waste Toner Type E Replacing the Waste Toner BottleZDJH230J J Plug in the power cable and turn on the power switchReplacing Consumables and Maintenance Kit H Push it in until it stopsTwo Stoppers Replacing the Paper Feed RollersPaper Feed Roller A Paper Feed Roller B Paper Feed Roller C ZERH070E ZERH040EZERH050E ZERH060EZERH090E K Slide all trays back into the print- er slowly until it stopsReplacing the Paper Feed Rollers Replacing Consumables and Maintenance Kit cause it could be very hot 2. Clearing and Adjusting the PrinterCautions to Take When Cleaning When removing misfed paper, do not touch the fusing section beThe registration roller is set shown in the illustration Cleaning the Registration RollerClean the roller when replacing the black Development Unit Cleaning the DustProof Glass Maintenance Color Regist Adjusting the Color RegistrationAuto Adjust Menu MaintenanceMaintenance Color Regist Fuser AdjustCompleted Color Regist Auto Adjust Menu MaintenanceInvalid Value Cannot Adjust Color Regist Fuser AdjustCannot Adjust See User’s Guide Fuser Adjust At Unit ReplaceMaintenance Color Regist Fuser Adjust Custom AdjustCustom Adjust Plain 600dpi Menu MaintenancePress # for Test Print Bypass Manual AdjustSelect Action 0 Exit Select Action 1 Re-adjust Select Action +1 Re-adjustAdjustment A -7.0 +7.0 +2 Color Regist Manual AdjustManual Adjust Print Result Adjustment A -7.0 +7.0 +0ColorRegistSheet Test Sheet SamplesFuser Adjust Sheet Clearing and Adjusting the PrinterAdjusting the Color Registration Fuser Adjust SheetBlack Adjusting the Image DensityMaintenance Image Density Image Density BlackRegistration Prt. Test Sheet Adjusting the Registration of the TraysMaintenance Registration Registration AdjustmentReady Adjustment Vert. TrayVert. Tray 3 -4.0 +4.0 C Press U or T to display the tray to adjust, and then pressRemoving Misfed Paper in the Duplex Feed Unit 3. AppendixH Close the Duplex Feed Unit ZDJH041J L Plug in the power cable and turn on the power switchRemoving Misfed Paper in the Duplex Feed Unit Close Front Cover When the Front Cover Does Not CloseZDJH041J F Plug in the power cable and turn on the power switchWhen the Front Cover Does Not Close Staple Cartridge ConsumablesToner cartridge Average printable number of Other consumablesName ConsumablesTypes of Paper and Other Media Paper RecommendationsLoading Paper Storing PaperPaper Recommendations Thick PaperOHP transparencies Paper not supported by this printer EnvelopesPrintable Area INDEX Copyright UE USA G060-6920