Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual H Close the Duplex Feed Unit

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 54

Image 54

Appendix

E Pinch the upper left area of the Duplex Feed Unit, and pull it out slowly halfway.

ZDJP213J

F Holding the Duplex Feed Unit firmly with both hands, pull it straight out.

ZDJP214J

G Place the Duplex Feed Unit on the floor slowly. Open it slowly, and remove the misfed paper.

ZDJP215J

Important

❒Do not open the Duplex Feed Unit by force. It might damage the unit.

H Close the Duplex Feed Unit.

I Holding the Duplex Feed Unit with both hands, insert it along the rails slowly until it stops.

ZDJP056J

The top and bottom rails are locat- ed in the position shown in the il- lustration.

ZDJP133J

There are two arrows located on the left and right sides of the Du- plex Feed Unit.

J Refasten the Duplex Feed Unit using provided screwdriver. Use the screw that was removed in step D.

ZDJP057J

Page 54

Image 54

Savin SLP38C manual H Close the Duplex Feed Unit

Contents

Maintenance Guide For safety, please follow the instructions in this manualOperating Instructions Introduction Trademarks Safety Information Safety During OperationR WARNING R CAUTION ENERGY STAR Program Low-power Mode Energy Saver modeSpecifications Preparation How to Read This ManualSymbols Limitation2.Clearing and Adjusting the Printer TABLE OF CONTENTS1.Replacing Consumables and Maintenance Kit 3.Appendix1. Replacing Consumables and Maintenance Kit Detaching the SR770 2 Tray FinisherOpening and Closing the Duplex Reversal Unit A Push up the lock release button and keep it in placeB Lower the Duplex Reversal Unit slowly until it stops Replacing the Toner Cartridge Add Toner XXXAdd Toner XXX/XXX B Remove the toner cartridge for the color you want to replace Loading Toner G Close the upper right coverReference Replacing the Fuser Oil UnitReplace Fuser Oil Unit TypeG See P.1 “Detaching the SR770 2 Tray Finisher”H Put the removed Fusing Unit in a stable and level place See P.2 “Opening and Closing the Duplex Reversal Unit” P If the Duplex Unit is installed, close the Duplex Reversal UnitReference Referencecartridges by yourself, dispose R Plug in the power cable and turn on the power switchIf you dispose of the used toner of them according to local regu- lationsReplacing the Photoconductor Unit Replace Black PCU Type FReplace Color PCU Type A F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replacing the Development Unit Replace Black Dev. UnitTypeDReplace Color Dev. UnitTypeB Page Page Please Wait Reference Replacing the Fusing UnitReplace Fusing Unit Type C See P.1 “Detaching the SR770 2 Tray Finisher”I Remove the Fuser Oil Unit in the direction of the arrow Please Wait Press # for Fuser AdjustInitializing Please Wait CalibratingSet Sheet in Bypass, then # Invalid Value Press # A B C D E F G H 0 0 0 0 0 0 0Ready ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust”Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replacing the Waste Toner Bottle Replace Waste Toner Type EH Push it in until it stops J Plug in the power cable and turn on the power switchReplacing Consumables and Maintenance Kit ZDJH230JReplacing the Paper Feed Rollers Paper Feed Roller A Paper Feed Roller B Paper Feed Roller CTwo Stoppers ZERH060E ZERH040EZERH050E ZERH070EK Slide all trays back into the print- er slowly until it stops Replacing the Paper Feed RollersZERH090E Replacing Consumables and Maintenance Kit When removing misfed paper, do not touch the fusing section be 2. Clearing and Adjusting the PrinterCautions to Take When Cleaning cause it could be very hotCleaning the Registration Roller Clean the roller when replacing the black Development UnitThe registration roller is set shown in the illustration Cleaning the DustProof Glass Menu Maintenance Adjusting the Color RegistrationAuto Adjust Maintenance Color RegistMenu Maintenance Fuser AdjustCompleted Color Regist Auto Adjust Maintenance Color RegistFuser Adjust At Unit Replace Color Regist Fuser AdjustCannot Adjust See User’s Guide Invalid Value Cannot AdjustMenu Maintenance Fuser Adjust Custom AdjustCustom Adjust Plain 600dpi Maintenance Color RegistSelect Action +1 Re-adjust Manual AdjustSelect Action 0 Exit Select Action 1 Re-adjust Press # for Test Print BypassAdjustment A -7.0 +7.0 +0 Color Regist Manual AdjustManual Adjust Print Result Adjustment A -7.0 +7.0 +2Clearing and Adjusting the Printer Test Sheet SamplesFuser Adjust Sheet ColorRegistSheetFuser Adjust Sheet Adjusting the Color RegistrationImage Density Black Adjusting the Image DensityMaintenance Image Density BlackRegistration Adjustment Adjusting the Registration of the TraysMaintenance Registration Registration Prt. Test SheetC Press U or T to display the tray to adjust, and then press Adjustment Vert. TrayVert. Tray 3 -4.0 +4.0 Ready3. Appendix Removing Misfed Paper in the Duplex Feed UnitH Close the Duplex Feed Unit L Plug in the power cable and turn on the power switch Removing Misfed Paper in the Duplex Feed UnitZDJH041J When the Front Cover Does Not Close Close Front CoverF Plug in the power cable and turn on the power switch When the Front Cover Does Not CloseZDJH041J Consumables Toner cartridgeStaple Cartridge Consumables Other consumablesName Average printable number ofStoring Paper Paper RecommendationsLoading Paper Types of Paper and Other MediaThick Paper OHP transparenciesPaper Recommendations Envelopes Paper not supported by this printerPrintable Area INDEX Copyright UE USA G060-6920