Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual Replacing the Fusing Unit, Replace Fusing Unit Type C, Reference

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 26

Replacing the Fusing Unit

Replacing Consumables and Maintenance Kit

Replacing the Fusing Unit

1

RCAUTION:

•The Fusing Unit becomes very hot. When installing the new Fusing Unit, turn off the printer and wait about an hour. After that, install the new Fusing Unit. Not waiting for the unit to cool down can result in a burn.

If "Replace Fusing Unit (Type C)" ap- pears on the panel display, replace the Fusing Unit.

Replace Fusing

Unit (Type C)

A Turn off the power switch and unplug the power cable.

Important

❒Be sure to wait about an hour to prevent a burn.

B If the 2 Tray Finisher is installed, detach it from the printer.

Reference

See P.1 “Detaching the SR770 (2 Tray Finisher)”

C If the Duplex Unit is installed, open the Duplex Reversal Unit.

Reference

See P.2 “Opening and Closing the Duplex Reversal Unit”

D If the External Tray is attached to the printer, raise it in the direc- tion of the arrow (A), and remove

it (B).

ZDJP038J

E Pull out the left cover of the print- er.

ZDJH047J

F Open the upper left cover.

ZDJH048J

Important

❒Do not touch any areas other than the handle.

18

Image 26

Savin SLP38C manual Replacing the Fusing Unit, Replace Fusing Unit Type C, Reference

Contents

Operating Instructions Maintenance GuideFor safety, please follow the instructions in this manual Introduction Trademarks R WARNING Safety InformationSafety During Operation R CAUTION Specifications ENERGY STAR ProgramLow-power Mode Energy Saver mode Preparation How to Read This ManualSymbols Limitation2.Clearing and Adjusting the Printer TABLE OF CONTENTS1.Replacing Consumables and Maintenance Kit 3.Appendix1. Replacing Consumables and Maintenance Kit Detaching the SR770 2 Tray FinisherB Lower the Duplex Reversal Unit slowly until it stops Opening and Closing the Duplex Reversal UnitA Push up the lock release button and keep it in place Add Toner XXX/XXX Replacing the Toner CartridgeAdd Toner XXX B Remove the toner cartridge for the color you want to replace Loading Toner G Close the upper right coverReference Replacing the Fuser Oil UnitReplace Fuser Oil Unit TypeG See P.1 “Detaching the SR770 2 Tray Finisher”H Put the removed Fusing Unit in a stable and level place See P.2 “Opening and Closing the Duplex Reversal Unit” P If the Duplex Unit is installed, close the Duplex Reversal UnitReference Referencecartridges by yourself, dispose R Plug in the power cable and turn on the power switchIf you dispose of the used toner of them according to local regu- lationsReplace Color PCU Type A Replacing the Photoconductor UnitReplace Black PCU Type F F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replace Color Dev. UnitTypeB Replacing the Development UnitReplace Black Dev. UnitTypeD Page Page Please Wait Reference Replacing the Fusing UnitReplace Fusing Unit Type C See P.1 “Detaching the SR770 2 Tray Finisher”I Remove the Fuser Oil Unit in the direction of the arrow Please Wait Press # for Fuser AdjustInitializing Please Wait CalibratingSet Sheet in Bypass, then # Invalid Value Press # A B C D E F G H 0 0 0 0 0 0 0Ready ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust”Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replacing the Waste Toner Bottle Replace Waste Toner Type EH Push it in until it stops J Plug in the power cable and turn on the power switchReplacing Consumables and Maintenance Kit ZDJH230JTwo Stoppers Replacing the Paper Feed RollersPaper Feed Roller A Paper Feed Roller B Paper Feed Roller C ZERH060E ZERH040EZERH050E ZERH070EZERH090E K Slide all trays back into the print- er slowly until it stopsReplacing the Paper Feed Rollers Replacing Consumables and Maintenance Kit When removing misfed paper, do not touch the fusing section be 2. Clearing and Adjusting the PrinterCautions to Take When Cleaning cause it could be very hotThe registration roller is set shown in the illustration Cleaning the Registration RollerClean the roller when replacing the black Development Unit Cleaning the DustProof Glass Menu Maintenance Adjusting the Color RegistrationAuto Adjust Maintenance Color RegistMenu Maintenance Fuser AdjustCompleted Color Regist Auto Adjust Maintenance Color RegistFuser Adjust At Unit Replace Color Regist Fuser AdjustCannot Adjust See User’s Guide Invalid Value Cannot AdjustMenu Maintenance Fuser Adjust Custom AdjustCustom Adjust Plain 600dpi Maintenance Color RegistSelect Action +1 Re-adjust Manual AdjustSelect Action 0 Exit Select Action 1 Re-adjust Press # for Test Print BypassAdjustment A -7.0 +7.0 +0 Color Regist Manual AdjustManual Adjust Print Result Adjustment A -7.0 +7.0 +2Clearing and Adjusting the Printer Test Sheet SamplesFuser Adjust Sheet ColorRegistSheetFuser Adjust Sheet Adjusting the Color RegistrationImage Density Black Adjusting the Image DensityMaintenance Image Density BlackRegistration Adjustment Adjusting the Registration of the TraysMaintenance Registration Registration Prt. Test SheetC Press U or T to display the tray to adjust, and then press Adjustment Vert. TrayVert. Tray 3 -4.0 +4.0 Ready3. Appendix Removing Misfed Paper in the Duplex Feed UnitH Close the Duplex Feed Unit ZDJH041J L Plug in the power cable and turn on the power switchRemoving Misfed Paper in the Duplex Feed Unit When the Front Cover Does Not Close Close Front CoverZDJH041J F Plug in the power cable and turn on the power switchWhen the Front Cover Does Not Close Staple Cartridge ConsumablesToner cartridge Consumables Other consumablesName Average printable number ofStoring Paper Paper RecommendationsLoading Paper Types of Paper and Other MediaPaper Recommendations Thick PaperOHP transparencies Envelopes Paper not supported by this printerPrintable Area INDEX Copyright UE USA G060-6920