Manuals / Savin / Computer Equipment / Printer

Savin SLP38C manual Replacing the Development Unit, Replace Black Dev. UnitTypeD

Models: SLP38C

1 66

Download 66 pages 29.39 Kb

Page 22

Replacing the Development Unit

Replacing Consumables and Maintenance Kit

Replacing the Development Unit

If "Replace Black Dev. Unit(TypeD)"

1 appears on the panel display, replace the black Development Unit.

C Take out the green screwdriver.

Use this screwdriver for all attach- ment and detachment of screws.

Replace Black

Dev. Unit(TypeD)

If "Replace Color Dev. Unit(TypeB)" appears on the panel display, replace the three color (CMY) Development Units.

Replace Color

Dev. Unit(TypeB)

Note

❒A dustproof filter is attached to the black Development Unit. When replacing the black Development Unit, also replace the dustproof fil- ter. See P.23 “Replacing the Dust- proof Filter”.

❒When replacing the black Devel- opment Unit, clean the registration roller. See P.32 “Cleaning the Regis- tration Roller”.

A Turn off the power switch and unplug the power cable.

B Open the front cover slowly by pulling down from the two areas on the left and right.

ZDJH007J

ZDJH013J

D Turn the light brown lever coun- terclockwise.

ZDJH014E

E Loosen two screws that are fasten- ing the inner cover using provid- ed screwdriver.

ZDJH015J

You cannot remove these two screws.

14

Image 22

Savin SLP38C manual Replacing the Development Unit, Replace Black Dev. UnitTypeD, Replace Color Dev. UnitTypeB

Contents

For safety, please follow the instructions in this manual Maintenance GuideOperating Instructions Introduction Trademarks Safety During Operation Safety InformationR WARNING R CAUTION Low-power Mode Energy Saver mode ENERGY STAR ProgramSpecifications Preparation How to Read This ManualSymbols Limitation2.Clearing and Adjusting the Printer TABLE OF CONTENTS1.Replacing Consumables and Maintenance Kit 3.Appendix1. Replacing Consumables and Maintenance Kit Detaching the SR770 2 Tray FinisherA Push up the lock release button and keep it in place Opening and Closing the Duplex Reversal UnitB Lower the Duplex Reversal Unit slowly until it stops Add Toner XXX Replacing the Toner CartridgeAdd Toner XXX/XXX B Remove the toner cartridge for the color you want to replace Loading Toner G Close the upper right coverReference Replacing the Fuser Oil UnitReplace Fuser Oil Unit TypeG See P.1 “Detaching the SR770 2 Tray Finisher”H Put the removed Fusing Unit in a stable and level place See P.2 “Opening and Closing the Duplex Reversal Unit” P If the Duplex Unit is installed, close the Duplex Reversal UnitReference Referencecartridges by yourself, dispose R Plug in the power cable and turn on the power switchIf you dispose of the used toner of them according to local regu- lationsReplace Black PCU Type F Replacing the Photoconductor UnitReplace Color PCU Type A F Lift the inner cover until it clicks into place and holds H Install a new Photoconductor Unit Calibrating Replace Black Dev. UnitTypeD Replacing the Development UnitReplace Color Dev. UnitTypeB Page Page Please Wait Reference Replacing the Fusing UnitReplace Fusing Unit Type C See P.1 “Detaching the SR770 2 Tray Finisher”I Remove the Fuser Oil Unit in the direction of the arrow Please Wait Press # for Fuser AdjustInitializing Please Wait CalibratingSet Sheet in Bypass, then # Invalid Value Press # A B C D E F G H 0 0 0 0 0 0 0Ready ⇒ P.3 “Replacing the Toner Car- tridge” ⇒ P.34 “Auto Adjust”Replacing the Dustproof Filter Replacing the Dustproof Filter1 them into the box which con- tained the black Development Unit Replacing the Waste Toner Bottle Replace Waste Toner Type EH Push it in until it stops J Plug in the power cable and turn on the power switchReplacing Consumables and Maintenance Kit ZDJH230JPaper Feed Roller A Paper Feed Roller B Paper Feed Roller C Replacing the Paper Feed RollersTwo Stoppers ZERH060E ZERH040EZERH050E ZERH070EReplacing the Paper Feed Rollers K Slide all trays back into the print- er slowly until it stopsZERH090E Replacing Consumables and Maintenance Kit When removing misfed paper, do not touch the fusing section be 2. Clearing and Adjusting the PrinterCautions to Take When Cleaning cause it could be very hotClean the roller when replacing the black Development Unit Cleaning the Registration RollerThe registration roller is set shown in the illustration Cleaning the DustProof Glass Menu Maintenance Adjusting the Color RegistrationAuto Adjust Maintenance Color RegistMenu Maintenance Fuser AdjustCompleted Color Regist Auto Adjust Maintenance Color RegistFuser Adjust At Unit Replace Color Regist Fuser AdjustCannot Adjust See User’s Guide Invalid Value Cannot AdjustMenu Maintenance Fuser Adjust Custom AdjustCustom Adjust Plain 600dpi Maintenance Color RegistSelect Action +1 Re-adjust Manual AdjustSelect Action 0 Exit Select Action 1 Re-adjust Press # for Test Print BypassAdjustment A -7.0 +7.0 +0 Color Regist Manual AdjustManual Adjust Print Result Adjustment A -7.0 +7.0 +2Clearing and Adjusting the Printer Test Sheet SamplesFuser Adjust Sheet ColorRegistSheetFuser Adjust Sheet Adjusting the Color RegistrationImage Density Black Adjusting the Image DensityMaintenance Image Density BlackRegistration Adjustment Adjusting the Registration of the TraysMaintenance Registration Registration Prt. Test SheetC Press U or T to display the tray to adjust, and then press Adjustment Vert. TrayVert. Tray 3 -4.0 +4.0 Ready3. Appendix Removing Misfed Paper in the Duplex Feed UnitH Close the Duplex Feed Unit Removing Misfed Paper in the Duplex Feed Unit L Plug in the power cable and turn on the power switchZDJH041J When the Front Cover Does Not Close Close Front CoverWhen the Front Cover Does Not Close F Plug in the power cable and turn on the power switchZDJH041J Toner cartridge ConsumablesStaple Cartridge Consumables Other consumablesName Average printable number ofStoring Paper Paper RecommendationsLoading Paper Types of Paper and Other MediaOHP transparencies Thick PaperPaper Recommendations Envelopes Paper not supported by this printerPrintable Area INDEX Copyright UE USA G060-6920