Assembly

 

 

 

 

en

 

 

Assemble the Steering Wheel

NOTES: All fasteners are in the parts bag. Do not

 

discard any parts or material until the unit

 

1.

Make sure the front wheels point forward as shown

is assembled.

 

 

Before doing any assembly or maintenance to the

 

 

in Figure 3.

 

 

2.

Slide the bellows (1) over the console.

mower, remove the wire from the spark plug.

 

Install the Front Wheels

 

3.

Slide the steering post (2) into the console.

 

4.

Attach the steering wheel (3) to the steering post

1.

Make sure the valve stem (1) is to the outside

 

 

(2) with screw (4) and washer (5). Tighten screw

 

(see Figure 1).

 

 

 

but be careful not to over-tighten.

2.

Slide the front wheel (2) onto the spindle (3).

 

 

a. Push on the steering wheel. The steering post

3.

Faster the front wheel (2) with washers (4 and 5),

 

 

will lock onto the pinion gear (6).

 

 

b. Pull on the steering wheel. Make sure that the

 

and cotter pin (6) Bend the ends of the cotter pin

 

 

 

apart to keep the front wheel on the spindle.

 

 

steering post is locked in place.

4.

If your model has hub caps (7), install the hubcaps.

5.

Install the plate (7) and cover (8) to the

 

Make sure the washers hold the hubcaps in place.

 

steering wheel.

5.

Repeat for opposite side.

 

 

Assemble the Grass Bag

Install the Seat

 

 

1.

Slide the bottom tube (1) onto the bagger frame (2)

1.

Carefully remove the plastic bag from the seat.

 

 

(see Figure 4).

 

2.

Align the h

les in b tt m tube with hole in the

2.

Raise the seat support (1) (see Figure 2).

 

 

 

bagger frame.

3.

Align the holes in the seat (2) to the slots in the

 

 

 

3.

Install he c

er pins (3) into holes and bend the

 

seat support.

 

 

 

 

 

 

ends o se ure o the frame.

4.

Install the seat (2) to the seat support (1) and

for4. Slide the frame assembly onto the grass bag (4).

 

adjustment lever (3) with washers (4) and b lts (5).

5.

Attach the bag clips to the frame assembly.

 

NOTE: Install the washers on the left side nly.

 

 

 

6.

Align the bagger cover (5) to holes in frame.

5.

Connect the wiring harness (6) to the seat switch

 

 

(7) under the seat.

 

 

7.

Use screws (6) and (7) to assemble the side and

6.

Lower the seat to the normal operatingNotposition.

 

8.

top of the cover to the bagger frame.

7.

Check the operation of the seat adjustment.

 

Assemble the bagger handle (8) thru hole in cover

 

 

and frame.

 

 

a.

If the seat needs adjustment, raise the

 

 

 

 

 

9.

Secure the bagger handle with washer (9), screw

 

 

adjustment lever (3) toward the s at and move

 

 

 

(10), and nut (11).

 

 

the seat to the desired position.

 

 

 

 

 

10. Install rear bagger handle (12) to cover using two

 

b.

Release the adjustment lever to lock the seat

 

 

 

 

screws (13).

 

 

in place.

 

 

 

 

 

Reproduction

 

 

 

14