Procedure
|
|
|
|
|
|
|
|
| 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| USER PGM | SNAP SHOT |
|
| 1 TITLE 2 | DSK | EDGE |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| STATUS EDIT |
|
|
EDITOR | LUM | LUM | LUM | TRAIL |
|
|
|
|
|
|
|
|
|
|
|
|
| SHADOW |
|
|
|
|
|
|
|
|
|
GPI | CRK | CRK | BORDER | BEVELD |
|
|
|
|
|
|
|
|
|
|
|
|
| EDGE | INITIAL |
|
|
|
|
| EDIT | LEARN |
|
SET UP | MASK | MASK | MASK | SOFT |
|
|
|
|
|
|
| RECALL |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
SHIFT | CCR | LIGHTING MATTES | BORDER | PATTERN PAGE | F1 | F2 | F3 | F4 | F5 |
| HOLD | LOCATION | |
|
|
|
|
| ADJ |
|
|
|
|
|
| INPUT |
|
|
|
|
|
|
|
|
| EFFECT |
|
|
|
| |
|
|
|
|
|
| TRANS RATE |
| DSK |
|
| PATTERN NUMBER |
| |
|
|
|
|
|
|
|
| FTB | SET |
|
|
| SET |
2
3
|
| CCR | TITLE 1 | TITLE 2 | DSK | SUPER BG FRGD 2 | MEMORY | FRAME | FREEZ | |
AUXILIARY |
|
| SOURCE | SOURCE | FILL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT |
BACKGROUND |
|
|
|
|
|
|
|
| VIDEO | |
|
|
|
|
|
|
|
|
| ||
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT |
VIDEO | ||||||||||
FOREGROUND |
|
|
|
|
|
|
|
|
| |
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT |
VIDEO |
MIX EFFECT
TITLE
CUT
AUTO
TRANS
N/R | REV | DIRECT | DIRECT | DSK PVW | |
|
| RECALL PATTERN |
| ||
|
|
| LAST X | FADE | |
7 | 8 | 9 |
| TO | |
INS | BLACK | ||||
4 | 5 | 6 | DEL |
| |
|
|
| P IN P | DSK | |
1 | 2 | 3 | RST | ||
|
DOWN UP ENTER
0
PATTERN/KEY PAD
4
5,78
<Preparation>
<Image selection>
<Effect selection>
10 9 1
1 Pull the fader lever toward you as far as it will go. 2 Press BACKGROUND Bus button 1.
The pressed button lights red, and the video signal connected to the VIDEO INPUT 1 connector is selected as the background image. The selected background image appears on the program monitor.
3 Press FOREGROUND Bus button 2.
The pressed button lights amber, and the video signal connected to the VIDEO INPUT 2 connector is selected as the foreground image.
To check the selected image on the program monitor, move the fader lever to the opposite end. After checking, return the lever to the position closest to you.
If a preview monitor is connected, the selected foreground image appears in the preview monitor.
4 Press the DIRECT PATTERN button, turning it on. (If it is already lit, omit this step.)
The unit is now in direct pattern selection mode. In this mode, you can select the eleven patterns assigned to buttons in the pattern/numeric keypad using the corresponding button.
(Continued)
Operation Basic 3 Chapter
Chapter 3 Basic Operation