Sony MAV-555SS P3 port Warning, RAID Sbxu Warning, RAID Sbxd Warning, RAID Battery Warning

P3 port Warning

Meaning: Detected a malfunction in the P3 port control area.

The DM-127 Board and DPR-189 (B) Board may be defective.

RAID SBX(U) Warning

Meaning: Detected a malfunction in communications between the FM-81 Board and RAID.

The FM-81 Board and PU-121 Board may be defective.

RAID SBX(D) Warning

Meaning: Detected a malfunction in communications with the FM-81 Board in the PU-121 Board.

The FM-81 Board and PU-121 Board may be defective.

RAID Battery Warning

Meaning: Detected a malfunction in the battery that maintains PU-121 Board settings.

The battery may be discharged.

RAID Flash Warning

Meaning: A Flash ROM malfunction detected in the PU- 121 Board.

The PU-121 Board may be defective.

HDD xx Warning

Meaning: Errors occur frequently while reading/writing HDD number xx.

HDD xx Fail

Meaning: HDD number xx cannot be used due to malfunction.

HDD xx Unknown HDD

Meaning: HDD number xx has not been recognized yet. This message appears when a new replacement HDD is inserted.

Remedy: Run -NEW HDD (menu 098) from the base menu and restore AV data to the new HDD. During restoration, “Rebuilding” is displayed on the front panel. Do not turn off the power until restoration is complete.

HDD xx SPC Error

Meaning: SPC connected to HDD number xx is not usable due to malfunction.

The IF-837 Board may be defective.

HDD xx No HDD

Meaning: No HDD is inserted in HDD slot number xx. EM Router Init. Fail

EM Router Init. Fail

Meaning: The video router on the EM-3 board cannot be initialized. The EM-3 board may be defective.

TM Warning LTC

Meaning: Either the correct time code signal is not being input to the TIMECODE IN (SYSTEM) jack on the rear panel, or there may be a hardware problem with the LTC Reader IC on the FM-81 board.

*Only a 1× time code signal can be input to the TIMECODE IN (SYSTEM) jack.

Remedy: Check the signal that is being input to the TIMECODE IN (SYSTEM) jack. If the correct signal is being input, there may be a hardware problem with the LTC Reader IC (IC1101) on the FM-81 board.

EM Recorder Init. Fail

Meaning: Was unable to initialize the RP port on the EM- 3 board in the BVE mode.

EM Mixer Config Fail

Meaning: Detected a malfunction in communications between the EM-3 Board and the DSP. The EM-3 Board may be defective.

Temperature Rise

Meaning: The internal temperature of the unit is too high. If the unit is being used in a normal temperature environment, this error may indicate that the fan is not functioning properly.

Remedy: Confirm that no fan warning has been output.

LoopRec Will Stop

Meaning: The remaining available recording space is exceeded and partial save performed during loop recording. If recording continues, the available recording space becomes insufficient and recording is stopped.

Remedy: To continue recording, delete the partially saved file or the unnecessary unedited file to create space. Once the file is deleted and the warning display disappears, it is possible to continue loop recording.

Material Entry Full

Nearly Rec Stop

Rec Stopped

Not enough Space To Rec

Too Much Fragmentation

Temp. File Protected

These are all special errors that may occur while editing in BVE mode. For details on these errors, refer to Section 5- 5-9,“Editing-Related Error Messages” (page 5-9).

EF-30 Boot Fail

EF-30 ConfgFail

EF-31 ConfigFail

These errors can occur only with the BKMA-560 or BKMA-561 installed, and indicates that the EF-30 board or EF-31 board has malfunctioned.

Appendixes

Error Messages A-3 (E)