Sony PDW-F335KL, PDWF335L manual 167

Message	Meaning and action to take
Run Salvage	Salvage processing needs to be
	done on the disc. To record on the
	disc, eject the disc, insert it again,
	and execute salvage processing.
Salvage NG	Salvage processing failed. For
	details, see “Handling of Discs
	When Recording Does Not End
	Normally (Salvage Function)” on
	page 50.
REC INHI.!	The Write Inhibit tab of the disc is
	in the recording disabled position,
	or salvage processing needs to be
	done on the loaded disc. Set the
	tab to the recording enabled
	position. Or eject the disc, insert it
	again, and perform salvage
	processing.
HD 50I/25P	The loaded disc has a different
HD 60I/30P	recording format. Exchange the
HD 23P Disc	disc, or change the recording
525/60	format.
625/50
2CH×16 Clip
4CH×16 Clip
Index File!	There is an unsupported index file
	on the disc to which you are trying
	to record. Exchange or format the
	disc.
File System	There is an unsupported file
	system on the disc to which you
	are trying to record. Exchange or
	format the disc.
KEY INHI.! a)	Disc operations are not possible
	when the DC IN connector is not
	connected and the CA-755 is
	being used.
ILL. PLAY!	An A/V phase error occurred
	during playback. Stop the disc.
Lid Closed!	The lid of the disc compartment
	does not open. Check the lid.
Lid Open!	The lid of the disc compartment is
	not closed. Close it securely.
No Clip!	There are no clips recorded on the
	disc. Exchange for a recorded
	disc.
No Disc!	There is no disc loaded. Insert a
	disc and try the operation again.
STOP ONCE!	The operation is not possible while
REC mode!	the disc is being played or
	recorded. Stop the disc.
Disc Top!	The operation is not possible
Disc End!	because the disc is at the top or
	end.
Formatting!	The disc is being automatically
	formatted. Wait until the format
	ends.
Recording	The unit is writing to the file
	system. Wait until writing finishes.

Message	Meaning and action to take
No EM Space	Essence marks cannot be
EM Full!	inserted. For details, see
	“Recording Shot Marks” on
	page 65.
SB CLP mode	Press the SEL/SET button (four-
	way arrow key) up to clear the
	SUB CLIP indicator before
	carrying out the operation.
No SEL List	No clip list is selected. Create a
	new clip list, or load a clip list from
	the disc.
No List!	There is no clip list. Create a clip
	list.
No SUB Clip	There are no sub clips in the clip
	list. Register a sub clip, or load
	another clip list.
SUB Clip NG	The In and Out point positions are
	invalid. Set correct In and Out
	points.
MAX# SB CLP	The total number of sub clips is
	over the upper limit (300).
CL OVER DUR	The total duration of sub clips in
	the current clip list is over the
	upper limit (24 hours).
FAN Stopped	The main unit or drive fan has
DR-FAN Stop	stopped. Avoid use under high
	temperatures, turn off the power,
	and contact your Sony dealer.

a) REC INHI.! appears if you attempt to start recording.

Alarm messages during thumbnail search, scene selection, and clip list operations

Alarm messages may appear in the LCD monitor during thumbnail search, scene selection, and clip list operations. In this case, take the action indicated in the following table.

Message	Meaning and action to take
CANNOT EXPAND	The clip cannot be expanded into
		Appendix
CLIP ANY FURTHER.	button is pressed when the
	more blocks.
	This appears when the EXPAND
	number of block is maximum, or
	when the duration of an expanded
	thumbnail is 1 frame.
SELECTED ESSENCE	The selected essence mark does
MARK DOES NOT	not exist.
EXIST.	This appears in the essence mark
	selection screen when the
	specified essence mark does not
	exist on the disc.
SUB CLIP IS INVALID.	The temporal relationship between
SET APPROPRIATE	the specified In and Out points in a
IN/OUT POINTS.	TRIM operation (see page 92) is
	not correct.
	Reset so that the value of the Out
	point timecode is larger than the
	value of the In point timecode.

Operation Warnings 167