Rear Panel

POWER

AC IN

DC IN 12V=

1Power supply section (see

REMOTE

4 DC IN 12V connector

page 22)

 

 

 

 

5 REMOTE connector

2Analog audio signal input/ output section (see page 22)

3Digital audio signal input/ output section (see page 23)

 

ANALOG AUDIO INPUT

 

ANALOG AUDIO OUTPUT

AUDIO MONITOR

 

 

 

 

 

 

 

 

1

2

1

2

R

L

DIGITAL AUDIO (AES/EBU)

 

HDSDI INPUT

HDSDI OUTPUT

 

 

IN

1/2

3/4

 

1

 

2

 

 

 

 

 

 

 

(SUPER)

 

COMPOSITE OUTPUT

REF.VIDEO INPUT

1

2(SUPER)

IN

OUT

SDSDI OUTPUT

12

(SUPER)

1/23/4

4HDSDI signal input/output section (see page 23)

6COMPOSITE OUTPUT1, 2 (SUPER) connectors

7REF.VIDEO INPUT connectors

Names 2 Chapter

 

VIDEO CONTROL

REMOTE(9P)

MAINTENANCE

TIME CODE

 

S400

IN OUT

5Timecode input/output

 

1 (i.LINK) S400 connector

 

 

 

 

 

 

 

 

section (see page 23)

 

 

 

 

 

8 (network) connector

2 VIDEO CONTROL connector

 

 

 

 

9 MAINTENANCE connectors

3 REMOTE(9P) connector

 

 

 

 

0 SDSDI OUTPUT1, 2

 

 

 

 

 

(SUPER) connectors

Parts of Functions and

a(i.LINK) S400 connector (6-pin, IEEE1394

compliant)

Connect a computer, or similar, using an i.LINK cable.

Notes

•When this unit is connected to a device with a 6-pin i.LINK connector by an i.LINK cable, before unplugging the i.LINK cable, first power off the device and disconnect the power plug from the outlet. If the i.LINK cable is unplugged with the device power plug still connected, a current from an excessive voltage (8 to 40 V) output from the i.LINK connector of the device flows into this unit. This may cause a failure of the unit.

•When connecting this unit to a device with a 6-pin i.LINK connector, connect to the 6-pin i.LINK connector of the other device first.

bVIDEO CONTROL connector (D-sub-9-pin)Connect an HKDV-900 video control unit.

cREMOTE(9P) (remote control 9-pin) connector

(D-sub 9-pin)

To control this unit from a controller or VTR supporting the RS-422A Sony 9-pin VTR protocol, connect the device to this connector.

dDC IN 12V connector (XLR 4-pin, male) Connect to a DC power source of 12 V.

When using the BKP-L551 Battery Adaptor to mount a battery pack, connect the power cable of the BKP-L551.

For details, see “Supplying power” on page 24.

eREMOTE connector (4-pin)

Supplies power to the RM-280 Editing Controller.

fCOMPOSITE OUTPUT 1, 2 (SUPER) (analog

composite video output 1, 2 (superimpose)) connectors (BNC type)

Output analog composite video signals. You can superimpose timecodes, menu settings, or error messages on the output of the 2 (SUPER) connector when CHAR SEL on the HOME page of the function menu is set to ON.

See “Basic Operations of the Function Menu” on page 39 for more information about the CHAR SEL setting.

gREF.VIDEO INPUT (reference video signal input) connectors (BNC type)

The two connectors form a loop-through connection; when a reference video signal is input to the left connector, the

same signal is input from the right connector ( ) to a connected device. When no connection is made to the right connector, the left connector is automatically terminated with an impedance of 75 ohms.

h (network) connector (RJ-45 type)

This is a 10BASE-T/100BASE-TX/1000BASE-T connector for network connection.

CAUTION

For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.

Rear Panel 21